saisri1

updated

19 years ago

S

saisri1

2 Posts

0

773

June 10th, 2007 20:00

New comer from Sun storages to EMC symmetrix

Hi All

I am new comer to EMC storage boxes, and i need to start configuring and administering EMC DMX series boxes , but i am having good expertise with Sun storages.

I gone through the documentation , where it mostly points on architecture
and little info about hyper volumes and meta volumes etc.,,

I need to know more emphasis on, how physical disks are converted to LUNS and present to host, which software we normally use.

Is there any command line interface ?

I am sure there are lot of documentation in power link site which will have this information, But I need pointers from which doc's to start with . So that i can configure especially DMX 3000 box properly.

Thanks in Advance
Sri
  • 400

    0

    Posted June 12th, 2007 06:00

    The following manual is a good starting point:
    EMC Solutions Enabler Symmetrix Array Management CLI Product Guide, P/N 300-002-939.

    From the Home page on Powerlink (Powerlink.emc.com), click Support > Documentation/White Paper Library > Software S > Solutions Enabler > General Reference
  • bruce9991

    4 Posts

    400

    0

    Posted June 13th, 2007 01:00

    Hi All

    I am new comer to EMC storage boxes, and i need to
    start configuring and administering EMC DMX series
    boxes , but i am having good expertise with Sun
    storages.

    I gone through the documentation , where it mostly
    points on architecture
    and little info about hyper volumes and meta volumes
    etc.,,

    I need to know more emphasis on, how physical disks
    are converted to LUNS and present to host, which
    software we normally use.

    The DMX is configured with hypers and metas based on the archiecture design you have with EMC CE.

    The results would be delievered as a BIN file. You can call this BIN file a layout file that determines the configuration of how many hypers, the size of the hypers, metas.

    Hypers can be presented to the host as is (small luns) or group as metas using command line interface. Hypers are usually presented to the hosts and then you will use volume manager (VXVM) or disksuite (not recommended but works fine if you have very very simple configuration).

    Unfortunately, you may need to forget some of the stuff you learn from other storage vendors in order to get a good feel of how the DMX works.

    Is there any command line interface ?

    The command line interface package is called solutions enabler or SYMCLI

    I am sure there are lot of documentation in power
    link site which will have this information, But I
    need pointers from which doc's to start with . So
    that i can configure especially DMX 3000 box
    properly.

    Thanks in Advance
    Sri
  • bruce9991

    4 Posts

    400

    1

    Posted June 13th, 2007 01:00

    Hi All

    I am new comer to EMC storage boxes, and i need to
    start configuring and administering EMC DMX series
    boxes , but i am having good expertise with Sun
    storages.

    I gone through the documentation , where it mostly
    points on architecture
    and little info about hyper volumes and meta volumes
    etc.,,

    I need to know more emphasis on, how physical disks
    are converted to LUNS and present to host, which
    software we normally use.

    The DMX is configured with hypers and metas based on the archiecture design you have with EMC CE.

    The results would be delievered as a BIN file. You can call this BIN file a layout file that determines the configuration of how many hypers, the size of the hypers, metas.

    Hypers can be presented to the host as is (small luns) or group as metas using command line interface. Hypers are usually presented to the hosts and then you will use volume manager (VXVM) or disksuite (not recommended but works fine if you have very very simple configuration).

    Unfortunately, you may need to forget some of the stuff you learn from other storage vendors in order to get a good feel of how the DMX works.

    Is there any command line interface ?

    The command line interface package is called solutions enabler or SYMCLI

    I am sure there are lot of documentation in power
    link site which will have this information, But I
    need pointers from which doc's to start with . So
    that i can configure especially DMX 3000 box
    properly.

    Thanks in Advance
    Sri