I could do with some help which must be in the simplest of laymans terms as I don't know my aspi from my ide. I have downloaded and installed the new firmware upgrade for my dvd rewiter in the belief that it would give me a dual format writer, i.e. both +r & -r. So question one is am I mistaken in this belief. question two, if I'm not mistaken in my belief, is can some one please give me a blow by blow account of how to get the new driver to be recognised by the device manager as the new driver, at the moment when I request it to install the new driver it says the best driver is already installed, but the date on it is 1/7/2001.
if you can help it would be much appreciated, but remember to explain it as if you were talking to a child as I am not to knowledgeable on the inner workings. I've read the instructions by Stephen (moderator) but to a newbie they are too technical, for instance is an ATA storage controller the same as an ATA storage driver, where do I look to find out whats a slave and whats a master.
When I first bought my dimension 4550, I didn't know there was two formats and bought a lot of dvd-r discs and, you guessed it, my uses dvd+r, therefore if I can convert to dual format I will not have wasted my money.
#1) did you try to run the filename R59801.exe? if so, what it just did was to update the driver of your DVDRW drive. (a driver is the software needed to run a hardware device, in this case the DVDRW drive) and add the features indicated in the "Fixes and Enhancements" sections.
#2) i apologize but i'm not sure if i understand your second question correctly. can you please as to when you get the error? also, do you mean that the DVDRW drive is not being detected properly asfter trying to install the firmware?
#3) On Master and Slave: the motherboard has two main controllers: the Primary Controller and the Secondary Controller.
On each each controller, we can attach two IDE devices (like HardDrive, CDROM, CDRW, DVDRW, zip drives, etc). And since there are two devices, one would be called the "Master" and the other is the "Slave".
For instance, you system has only one HardDrive. Dell, by default attaches it to the Primary Controller. Hence, it is the Primary Master Device. If you attach a second HardDrive to the Primary Controller, it would be the Primary Slave Device.
CDROM, CDRW or DVDRW drives are usually attached to the Secondary Controller. If there are two drives, the first one (Usually located as the top tray) is the Secondary Master Drive. The second drive (usually the bottom or lower tray) is the Secondary Slave Drive.
The 1100A is a +R/+RW writer only. There would be almost no reason for NEC to release a firmware that would upgrade the 1100A to be able to write the "-" format because they already sell such a writer in the 1300A. There has been alot of work from people trying to hack to the 1300A firmware to run on the 1100A and get the 1100A to be able to write in both formats. However, nothing has worked yet so there's likely enough differences on the 1100A that prevents it from being able to write in the "-" format.
Hi Chris, I’m going to do a couple of things that are out of character / style for me normally, quote your post and cover / clear up a few issues. Not my intention to come across as a smarta__ I respect both accords & kinny`s posts in this matter…In my post you will find a CD/RW gif that links to a Help page which has articles from Dell, Microsoft, Roxio, Dell-Moderators and mostly from our Regular members here, their tips, suggestions, expertise, when I reference a Section and article this is the site I am referring to OK.
I could do with some help which must be in the simplest of laymans terms as I don't know my aspi from my ide.
If you are truly interested knowing information on this, click on the link and scroll to Sections 7-0 and 7-5
I have downloaded and installed the new firmware upgrade for my dvd rewiter in the belief that it would give me a dual format writer, i.e. both +r & -r. So question one is am I mistaken in this belief.
Unfortunately you are mistaken, even though accord done what we call “cut” a post by stepping over kinny`s, he covered this well.
question two, if I'm not mistaken in my belief, is can some one please give me a blow by blow account of how to get the new driver to be recognised by the device manager as the new driver, at the moment when I request it to install the new driver it says the best driver is already installed, but the date on it is 1/7/2001.
Part of this question is basically answered above, “Firmware” and “Driver” are not the same in this matter. The Firmware is like a BIOS, for more information on this, go to Section 7-0, article 8, this will explain it better. The “Driver” you are referencing above is generic to your Operating System, Windows 98, 2000, XP, etc and the date relates to that fact, if Microsoft issues any driver updates, you`ll need to find these through Windows Updates.
if you can help it would be much appreciated, but remember to explain it as if you were talking to a child as I am not to knowledgeable on the inner workings. I've read the instructions by Stephen (moderator) but to a newbie they are too technical, for instance is an ATA storage controller the same as an ATA storage driver,
I have actually heard people use the terms loosely but normally one considers the “controller” a device and the “driver” the software. Although this is most likely irrelevant considering you have already flashed the drive with the new firmware, here is post from Dell-Cody in regards to the instruction:
All Operating Systems; • Run Start/Settings/ControlPanel • Double-click Add/Remove Programs • Highlight the 'Intel Ultra ATA Storage Driver' entry • Select the Add/Remove button • You will be prompted to reboot once the uninstall script has completed • You may also click on the Uninstall icon located in the programs->Intel® Ultra ATA Storage Driver Menu
where do I look to find out whats a slave and whats a master.
Click on the CD/RW link and scroll to Section 4, article 3, this will explain the Master / Slave issue The motherboard has a Primary and Secondary Channel / Port, these are not referred to as Master / Slave. The ATA/ standard allows each channel to support two devices, this is where Master / Slave comes into play. Dell ships their systems using the Cable Select Feature, the jumper, shunt (Strap for my buddy Jack) for both drives will be set on CS and location on the IDE cable determines Master / Slave with the “End” connection as Master. The Master / Slave jumper settings, usually MS | SL, is designed to be able to over-ride the Cable Select Feature, thus location on the IDE does not matter.
When I first bought my dimension 4550, I didn't know there was two formats and bought a lot of dvd-r discs and, you guessed it, my uses dvd+r, therefore if I can convert to dual format I will not have wasted my money.
thank you
I am fairly sure you `re not the only person to purchase the wrong media, hopefully you were able to exchange it. As for a dual format drive, before looking at the NEC 1300, browse a little, the Sony DRU 510 is getting very good reviews. Best Regards
God, grant me the senility to forget the people I never liked anyway, the good fortune to run into the ones I do and the eyesight to tell the difference.
Thanks to you Kinny 168 and you Accord 1999 for your replies the former helped in understanding about master and slave, the latter has answered my question. So the real answer is to by a 1300a.
thanks for the interesting links, I haven't had time to absorb all the information but have put the page on my favourites so I can refer to it.
With regard to the -R disc's I couldn't exchange them because when I went back to the website I bought them from it clearly stated to make sure you were ordering the correct disc's so that goes down to experience.
However thanks again for your help because even at my age I am facinated by all aspects of computing and since I have signed up to several forums its like the stone in the pond syndrome, the technology just becomes more & more amazing.
Okay... I have upgraded the firmware but now my NEC 1100A does not work and I can't get anyone to help. The problem is that the ONLY part that does not work is getting sound. I can burn video and audio and I can read data and even view video - but I can not get any sound from DVDs or CDs in the drive.
I have checked the "use digital sound" box in the device properties box and everything should be working - but isn't.
All digital "files" on the hard disk or streaming via the Internet produce nice clear sound proving that the sound card and related software is working.
The Dimension 4550's only function is to act as a multimedia workstation/server and without sound is pretty useless.
Right first off I am not one of you computer genius's, I'm known as what's called a computer bluffer, that is everything is by trial and error with no technical knowledge, so treat this post with caution. Having said that when I downloaded the firmware upgrade for my nec 1100a to the 10GE, I had all sorts of problems, i.e. nero wouldn't recognize my recorder and loss of audio on DVD's, wouldn't erase re-recordable disc's, and on. Now I know this is an absolute begins fix but if you have Windows XP you have a system restore facility in system tools. I restored my system to a point prior to the download of 10GE and re-downloaded the software.
Apart from the fact that it still didn't make my 1100a a dual format recorder, which I now know why thanks to forum members, everything now works. The only explanation I can offer is that some of the files being transferred were somehow corrupted. I hope it works good luck.
my question may be simple, however I'm a newbie. I have a NEC ND 1100 A on my Dell 4550. I have burned RW's with success and am now starting to burn R's. I just purchased Memorex DVD+R's 4X. The information with the DVD says that I need a firmware upgrade. I've checked dell with out success and checked the website that Memorex gave me with the DVD's, however Dell nor NEC is listed as a choice. Any ideas on where I can get this upgrade or do I need it?
The firmware upgrade for your drive is on top of this board (cd/dvd devices)
Dim 4550 2.4G 533 512Mb DDR@333Mhz Maxtor 30GB 7200rpm Maxtor 120GB 7200rpm NVIDIA TI 4200 64MB SB Live with 5.1 16X DVD-Rom Drive 40X/10X/40X CD-RW Drive XP Home
kinny168
11 Posts
439
0
Posted August 8th, 2003 22:00
#1) did you try to run the filename R59801.exe? if so, what it just did was to update the driver of your DVDRW drive. (a driver is the software needed to run a hardware device, in this case the DVDRW drive) and add the features indicated in the "Fixes and Enhancements" sections.
#2) i apologize but i'm not sure if i understand your second question correctly. can you please as to when you get the error? also, do you mean that the DVDRW drive is not being detected properly asfter trying to install the firmware?
#3) On Master and Slave: the motherboard has two main controllers: the Primary Controller and the Secondary Controller.
On each each controller, we can attach two IDE devices (like HardDrive, CDROM, CDRW, DVDRW, zip drives, etc). And since there are two devices, one would be called the "Master" and the other is the "Slave".
For instance, you system has only one HardDrive. Dell, by default attaches it to the Primary Controller. Hence, it is the Primary Master Device. If you attach a second HardDrive to the Primary Controller, it would be the Primary Slave Device.
CDROM, CDRW or DVDRW drives are usually attached to the Secondary Controller. If there are two drives, the first one (Usually located as the top tray) is the Secondary Master Drive. The second drive (usually the bottom or lower tray) is the Secondary Slave Drive.
Hope that helps.