UNSOLVED

BL Park

updated

17 years ago

BP

BL Park

7 Posts

0

28000

September 22nd, 2009 05:00

Dimension 5150 not reading DVD's - MORE HELP PLEASE ........!!

I've had my Dimension 5150 for over three years (just out of lease / warranty) and I have not used it to view DVD's until now.   I wanted to load new software to copy VHS tapes to DVD's which came with a DVD installation disc and when the DVD is loaded the drive looks at it but does nothing and does not recognise the disc.    I have set the DVD Region to Region 2 for United Kingdom.    I have also followed the Dell troubleshooting advice and downloaded the latest driver (which was the same version installed but I loaded it anyway in case mine had been corrupted) but to no avail.   A troubleshooting guide did mention that if a drive is not used for a certain purpose for a while it can 'forget' it exists.    Drive works okay with CD RW.   There are two drivers listed in the drive hardware properties (WDC WD2500JS-75NCB1  Disc Drives) and (HL-DT-ST DVD+-RW GWA4164B   DVD/CD-ROM drives).

I would very much appreciate any suggestions before I embark on a costly investigation and repair.

  • Skybird

    1 Rookie

    •

    10871 Posts

    757

    0

    Posted September 22nd, 2009 14:00

    Run the Dell Diagnostics on the drive if it is on your hard drive.
    Press F12 at startup while the blue Dell shows on the screen.  This
    will enter the boot menu.  Choose Utility Partition or Diagnostics.
    Run the Custom Test on the drive and have a data DVD (not movie DVD)
    ready for the test.

  • BL Park

    7 Posts

    757

    0

    Posted September 23rd, 2009 10:00

    Skybird

    Thank you for your suggestion.   I ran the test as you suggested and it worked okay with the data DVD.   However any Movie DVD and the Pinnacle Dazzle Video Creator installation DVD are not recognized.      Anything further you can suggest or does it seem that I will need some technical intervention or perhaps a new drive?

    Best regards

  • Skybird

    1 Rookie

    •

    10871 Posts

    757

    0

    Posted September 23rd, 2009 10:00

    If you ran the Diagnostics and it read a data DVD, the drive is good.
    You stated "any Movie DVD and the Pinnacle Dazzle Video Creator installation
    DVD are not recognized".  Not recognized by the Diagnostics or by your
    system?  The Diagnostics will not recognize a movie DVD. 

    On your system, do you have a DVD Decoder (WinDVD, Cineplayer, etc.) installed?

    If you insert the Dazzle DVD in the drive, then in My Computer if you right-click
    the drive and select Explore, can you see the contents of the disc?

  • BL Park

    7 Posts

    757

    0

    Posted September 23rd, 2009 14:00

    Skybird

     

    Windows Media Player and Quicktime are the only media players I have but not sure if they decode DVD's.    The system was sold pre-loaded with all the necessary software so I just presumed as it has a DVD RW capability that it also had the requisite firmware / software to run the hardware.

    The diagnostics stated the DVD was not a data DVD and asked me to load a data DVD, which I did, and it recognized and tested it successfully.    If I insert a DVD Movie or the DVD Installation disc then through my computer I cannot see a disc name or view the contents.    Ostensibly the drive whirs and looks at it then nothing.

     

    Thank you again

    B

  • Marcus316

    7 Posts

    757

    0

    Posted September 23rd, 2009 16:00

    Are you getting some kind of error (e.g."format not supported")  when trying to open the DVD using media player?

    If you do, then it's just a decoder problem.

    But if the drive cannot read any type of DVD media (movie or data) then it could still be a software or drive problem.

    Try to boot from the OS cd that came with your system. If you have Windows XP MCE installed, then its a DVD installation disc. If you can boot from the DVD, the drive is ok. If not, then the drive is failing.

    If in case you were able to boot sucessfully using the OS installation disc, visit this link http://support.microsoft.com/kb/314060

    You can either run the FIX IT to automatically change the registry or do it manually at your own risk which the steps are also given on that site. But whatever you choose to do, make sure that you create a back up of your registry or simply create a restore point.

     

     

     

     

  • Skybird

    1 Rookie

    •

    10871 Posts

    757

    0

    Posted September 23rd, 2009 16:00

    To play a DVD movie, a DVD Decoder is required.  Try
    VLC Media Player (free) here ............

    http://www.videolan.org/vlc/

    The installation disc you are problems with should be
    a data disc.  Can you see the contents of the data DVD
    you used for the Diagnostics test that test good?

  • BL Park

    7 Posts

    757

    0

    Posted September 24th, 2009 11:00

    Skybird

     

    Please excuse my ignorance - I visited the videolan site and the VCL Media Player for windows page offers three different versions, which should I use? :-

    Windows Self-Extracting Package (17.7MB)

    Windows 7zip (no installer needed) (14.9MB)

    Windows zip packages (no installer needed) (32.1MB)

    Also do I just select Random Mirror or do I select UK from the full mirror list?

     

    Regards

    B

  • Skybird

    1 Rookie

    •

    10871 Posts

    757

    0

    Posted September 24th, 2009 13:00

    They are all the same; just different packaging.  Select
    the Windows Self-Extracting Package.  It may be easier
    to handle.  You can download it from any mirror site you
    desire.

  • BL Park

    7 Posts

    757

    0

    Posted September 28th, 2009 12:00

    Skybird

    Last time I shall bother you - the VCL software cannot see anything on the D drive either.     Any last thoughts before I throw in the towel and take it to a shop?

     

    Regards

    B

    Scotland

  • Skybird

    1 Rookie

    •

    10871 Posts

    1015

    0

    Posted September 28th, 2009 14:00

    Puzzling.  I should have asked earilier.  What is the brand annd model
    of the drive?  You can find this in the Device Manager .......

    Start | Control Panel | System in classic view | Hardware tab | Device Manager

    Click on the (+) next to DVD/CD-ROM drives.  Post the brand and model of the drive.