Confirm that the RAID controller status is OK. Take note of the raid controller identifier, normally it’s something along the lines of “RAID.Integrated.1-1” or “NonRAID.Integrated.1-1”
Run command “get storage.enclosure 1 BackplaneCurrentMode”, the command should say current mode is splitmode.
Run command “get storage.enclosure 1 BackplaneRequestedMode”, the command should say requestedmode=none.
Run command “set storage.enclosure 1 BackplaneRequestedMode UnifiedMode”
Repeat earlier step (12) of “get storage.enclosure 1 BackplaneRequestedMode”, and make sure requestedmode is set to UnifiedMode.
Run command “jobqueue create <raidcontroller identifier earlier in Step 10 (in our case, RAID.Integrated.1-1)-s TIME_NOW--realtime.” Ensure that the command went through successfully, you should get a response saying “job successfully created”.
Run “jobqueue view” until all jobs are completed.
Run serveraction powercycle command
Run the command “get storage.enclosure 1 BackplaneCurrentMode.” This tells you that the backplane is set to UnifiedMode.
DELL-Erman O
Social Media and Communities Professional
Dell Technologies | Enterprise Support Services
#IWork4Dell
Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!
hmm... then the enclosure doesn't support changing the backplane mode. Or if the expander is capable, the system permits the setting of split mode. However, before installing the second controller, it’s crucial to enable this mode.
The iDrac verifies the expander’s capability before permitting the configuration of this mode, but it doesn’t check for the presence of the second Perc controller.
Might be needed to clear system even log
racadm getsel <options>
If no arguments are specified, the entire log is displayed.
To display the number of SEL entries, type:
racadm getsel -i
To clear the SEL entries, type:
racadm clrsel
DELL-Erman O
Social Media and Communities Professional
Dell Technologies | Enterprise Support Services
#IWork4Dell
Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!
Record: 94 Date/Time: 05/03/2023 17:14:35 Source: system Severity: Critical Description: The storage BP1 SAS B0 cable is not connected, or is improperly connected. ------------------------------------------------------------------------------- Record: 95 Date/Time: 05/15/2023 07:15:25 Source: system Severity: Critical Description: The storage BP1 SAS B0 cable is not connected, or is improperly connected. ------------------------------------------------------------------------------- Record: 96 Date/Time: 05/15/2023 07:15:29 Source: system Severity: Critical Description: The chassis is open while the power is off. ------------------------------------------------------------------------------- Record: 97 Date/Time: 05/15/2023 07:15:34 Source: system Severity: Ok Description: The chassis is closed while the power is off. ------------------------------------------------------------------------------- Record: 98 Date/Time: 08/18/2023 05:57:49 Source: system Severity: Critical Description: The storage BP1 SAS B0 cable is not connected, or is improperly connected. -------------------------------------------------------------------------------
racadm getsel -i Total Records: 98
racadm clrsel The SEL was cleared successfully
Is that all, just clear system event log entries, and problem fixed ?
Firstly, be ensure the firmwares are up to date. Please reseated backplane cables at both ends then I would expect issue will resolved. But if the issue persist, then it could be hardware failure. I recommend contact your local support.
DELL-Erman O
Social Media and Communities Professional
Dell Technologies | Enterprise Support Services
#IWork4Dell
Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!
DELL-Erman O
Moderator
•
2984 Posts
•
14874 Points
0
0
Posted December 27th, 2023 13:49
Hello, Could you try this pls?
iDRAC GUI: iDRAC > Storage > Enclosure > Setup, then edit from Split to Unified mode.
You will need to Power Off (Restart won’t be enough) the server to apply the change
DELL-Erman O
Social Media and Communities Professional
Dell Technologies | Enterprise Support Services
#IWork4Dell
Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!