UNSOLVED

garftoys

updated

3 years ago

G

garftoys

1 Rookie

•

15 Posts

0

33287

April 27th, 2020 00:00

Dell WD19DC and "Display 2 isn't active" in Windows 10

Hi 

Precision 7730 with AMD WX7100 GPU, with the WD19DC and two external BenQ PD3200U 4k monitors, both connected via DP to the WD19DC.  Desired operation: 2 x 4k 60Hz screens using 8bit colour depth.  In fact, just as it says is supported on Page 18 of the WD19DC User Guide.

Windows 10 detects the second monitor, but says "Display 2 isn't active".  Here's what Windows 10 shows:

 

Windows 10 sees it but can't identify itWindows 10 sees it but can't identify it

Have tried with "Enable Switchable Graphics" enabled and disabled in BIOS - makes no difference.

Have tried with "Discrete Graphics Controller Direct Output Mode" enabled and disabled in BIOS - makes no difference.

Have tried with "Enabled Switchable Graphics" enabled and "Discrete Graphics Controller Direct Output Mode" disabled - makes no difference.

Have tried with "Enabled Switchable Graphics" disabled and "Discrete Graphics Controller Direct Output Mode" enabled - makes no difference.

Yes, all four possible combinations of those BIOS settings, as the manual is poor in describing what they actually achieve.

Precision 7730 BIOS GPU Settings.jpg

The laptop will display 2 x 4k @ 30Hz (sometimes, intermittent and only when running the Intel GPU), but will not run two external monitors at 3840 x 2160 and 60Hz, 8bit, RGB.

FYI - same cables and same monitors work absolutely fine at 4k and 60Hz with a TB18DC docking station, so this isn't a cable or monitor problem.  I can change which monitor "works" by swapping DP posts on the WD19DC.

Latest Dell blessed AMD WX7100 GPU driver installed.  Tried the more up to date AMD one - no difference.  Back with Dell driver.

Hoping someone out there can help tickle this thing into life.  I gave up on the TB18DC due to audio problems, now I have display problems ... meh.

Thanks in advance for any help you can provide!

 

  • DELL-Cares

    Moderator

    •

    27852 Posts

    •

    772 Points

    26789

    0

    Posted April 27th, 2020 01:00

    Hi @garftoys, thank you for sharing all these details and steps tried. Please private message us the service tag of the Precision system so that we can check on the system configuration and advice further. ^AM


    #IWork4Dell

    For all non-technical issues that require your private data, we must communicate via a private Direct Message
    Dell Partner GEM Program, Out of Warranty Support options, No free goodwill repair, Get a copy of your Dell invoice

  • athomedev

    3 Posts

    26731

    0

    Posted May 2nd, 2020 18:00

    I recently solved a different but similar sounding monitor detected/isn't active/no signal problem, but with a 7530 connecting from Thunderbolt directly to a Dell USB C monitor. I don't have any of the Dell docks, so this may or may not apply to your issue. Also I guess assuming the 7730 is something like the 7530.

    What worked for me was manually updating the Thunderbolt firmware (the update was never listed through the Support Assist driver scan/auto-update) - I upgraded from version 23 to the May 2019 firmware (version 41).

    https://www.dell.com/support/home/ca/en/cadhs1/drivers/driversdetails?driverid=kfc67&oscode=wt64a&productcode=precision-17-7730-laptop 

    Note that the firmware update recommends to update the Thunderbolt driver first (a separate update from the firmware), although the driver for me was already handled by the Support Assist auto-update way back when (I think the latest is also a 2019 update). You can manually browse all of the drivers and firmwares from the 7730 driver support page.

    https://www.dell.com/support/home/ca/en/cabsdt1/product-support/product/precision-17-7730-laptop/drivers

    After update:





    tb_firmware.png

    Hope this helps. Good luck!

  • garftoys

    1 Rookie

    •

    15 Posts

    26712

    0

    Posted May 4th, 2020 13:00

    @athomedev many thanks for your suggestion.  Quite astounding that this TB update doesnt' appear for my P7730 or for the TB18DC.

     

    When installing it, it seemed to go well - however it caused a blue screen near the end of the process.  Two forced power cycles afterwards, and my P7730 booted without issue once again.  Thunderbolt Controller NVM firmware was indeed (apparently) updated to 41.00.  I now have all the same versions of Thunderbolt software as you do.  Same problem.  Second display is detected, but no resolution available and no picture/signal sent to second monitor.  First monitor is running at 4K @ 59Hz.

     

    From memory Dell actually recommend that I do NOT use SupportAssist as it struggles to handle the complex sequence of firmware, BIOS and driver updates required to get a TB18DC to operate correctly.  Been there, done that.

     

  • Slee27

    1 Message

    25928

    0

    Posted July 31st, 2020 14:00

    I have the same issue with my dell Inspiron and wonder if you have solved this issue? If so, would you share how you solved it? 

  • garftoys

    1 Rookie

    •

    15 Posts

    25911

    0

    Posted August 1st, 2020 07:00

    @Slee27 after 4 months of to-ing and fro-ing with Dell, replacing my TB18DC then returning it, purchasing a WD19DC with my own money, then chasing Dell to refund my original TB18DC money to cover the cost, they swapped my Precision 7730 motherboard. This allowed me to run both monitors at 4k@60Hz. They were not able to get a definitive root cause. I went through worlds of pain with different support individuals asking me to try different monitors, change DP cables, etc. which of course was a pointless exercise as the monitors worked fine with my TB18DC - I had audio problems with the TB18DC. Dell seems to have a quality problem with their docking stations and related drivers and firmware. I am not planning on buying any more.

  • Agha Mohsen

    1 Message

    6799

    3

    Posted September 10th, 2022 20:00

    One solution that instantly resolved the issue for me was:
    1. Opening the "Intel Graphics Command Center" program.
    2. Click on "Display" tab (on left)
    3. Recongnize the deactivated screen, and click on the 3dots on it.
    4. Enable it !

  • Bruteforcer

    1 Rookie

    •

    15 Posts

    6001

    0

    Posted November 16th, 2022 04:00

    Great Agha! This solution worked perfectly for me! Many thanks!!!

  • garftoys

    1 Rookie

    •

    15 Posts

    5935

    0

    Posted November 18th, 2022 02:00

    Just so everyone knows, this was never resolved by Dell.  It took more than 3 months for Dell to refund me for the WD19DC, from the first time they agreed to do that.  I now have a Sonnet Echo11 TB4 docking station which performs wonderfully, with an M42U 10-bit 60Hz HDR monitor and a 10-bit 60Hz PD3200U.

  • Tumnus123

    1 Message

    0

    0

    Posted September 13th, 2023 14:39

    Agha's steps also worked for me, though the steps/controls were a little different, probably due to different versions... I opened "Intel UHD Graphics Control Panel" >> Multiple Displays >> Extended Desktop, then selected my external displays from the dropdowns, and clicked Apply -- bingo!

  • michal.wozniak

    1 Rookie

    •

    4 Posts

    0

    0

    Posted January 16th, 2024 08:53

    I have a very same problem. My computer is Precision 3581 and my docking station is WD19S 130W. Screens showed as inactive, I have tried so many things : reinstalling drivers, reseting the station, playing with settings and nothing worked. I have no idea. Weird thing is that: when I choose the display only on the screen 2 it works (on 1 over 3 screens). I can choose only my computer, or screen number 2... never two or three at the same time. 

    Do you guys have any ideas? Yesterday morning it was working well.