UNSOLVED

PGPhantom

updated

23 years ago

P

PGPhantom

76 Posts

0

21952

January 12th, 2004 14:00

PowerVault 136T - LTO2, Slow Backups.

I have multiple PV136T's but only one has 6 x LTO2 Drives.  LTO2 are supposed to give 30-35,000 KB/sec.  I am only seeing around 8,000.  On an HP 4/40 attached to a Unix box I get around 15,000 KB/sec on LTO.

PV136T w/6 x IBM ULTRIUM TD2 SCSI Sequential Devices.  Firmware on all is 37RH.
Attached via SCSI to an Adaptec 39160 controller.  2 drives are attached to each of three separate servers.  The drivers version for Windows 2000 is 5.0.5.3 which is the latest posted on Dell support.

Can anyone tell me why I am not getting better backup speed?

Thank you.

  • richard_g

    25 Posts

    240

    0

    Posted January 12th, 2004 16:00

    Are all six drives (between the three servers) having the same slow performance?  

    Here ar  esoem itesm that will affect tape backup:

     

  • PGPhantom

    76 Posts

    240

    0

    Posted January 12th, 2004 17:00

    Yes, Speeds are similar for all 3 media servers,  Adaptec controllers have been set at 160 (I have tried 80 as well).  Quiet times produce the same results.  In the past, drivers have always been the root cause so I am not sure if the IBM driver from Dell is the right driver?
  • PGPhantom

    76 Posts

    240

    0

    Posted January 12th, 2004 17:00

    You assumed correctly - I am running Veritas NetBackup DataCentre 4.5 FP5.  I find that their driver install program is more of a pain than anything else and it has never worked successfully for me which is why I set everything manually - But, maybe that is the problem?

     

    Although I doubt it as I have a PV122T  running at 16,000 KB/sec.  I would expect the local backups to be in excess of 25,000 KB/sec to rule out the network but even there I am only getting around 12,000 KB/sec - Now one thing, I am using LTO tapes at present and not LTO2 - Is there a difference in the tapes that could affect speeds?

  • richard_g

    25 Posts

    240

    0

    Posted January 12th, 2004 17:00

    (continuation from previous update)

    Items that can affect tape backup:

    1.  Network based backups are at the expense of the network bandwidth

    2.  If the hard disk is very busy due to normal traffic, this will impact tape.  Are there many "open file" on the source drive?

    3.  I would make sure that the drives are negotiating at the higher speeds with the SCSI adapter (view POST on server bootup).

    One way to easily check performance is to runa single backup job during quiet times and check performance.

  • richard_g

    25 Posts

    240

    0

    Posted January 12th, 2004 17:00

    Since you mentioned "media server", I assume you may be running with NetBackup or Backup Exec?  If so, you may want to use the Vertias Tape class drivers that get installed with their tape class driver installer program.  (you may need to get the latest driver installer from their website if you have earlier versions). 

     

     

  • richard_g

    25 Posts

    240

    0

    Posted January 12th, 2004 18:00

    Yes, using LTO1 tapes in an LTO-2 drive will have impact on drive performance.  You may see at most 20 MB/SEC versus the full 30 MB/SEC, but your performance is well below where it should be.  You may want to seriously consider going back to the Veritas tape class drivers.  But be sure to get the correct driver installer, whereras the LTO-2 support may be in an updated driver installer release.  The problem may be that those non-Veritas drivers may not be optimized for NetBackup. 
  • PGPhantom

    76 Posts

    240

    0

    Posted January 12th, 2004 19:00

    I downloaded NetBackupTapeDeviceDriverInstall_263300.exe from Veritas which I assume to be the latest driver install.  On one of the media servers, I ran the install but it tried to replace the IBM LTO2 drivers with HP LTO drivers and then aborted because the devices are not HP.  I take it that the IBM LTO2 drivers are not in the pack dated Oct 13, 2003.  Do you happen to know how to update the drivers list and where?

     

    Thanks gain.

  • richard_g

    25 Posts

    240

    0

    Posted January 12th, 2004 21:00

    I am not certain what is happening in your scenario there, but the latest drivers are already in there.  I would think that there is something that is conflicting with your installer.   Also, check your NetBackup device mapping files (external_robot_mapping and external_drive_mappings TXT files ).  These are NetBackup text files that map drives to robots.  The latest mapping files can be downloaded from the Veritas web site.  In general though, the driver installer is a straight forward program and usually never has problems.  Just as a suggestion, you may want to uninstall the tape drivers from the OS, than rerun the driver installer, this way, it will be a clean driver install.   (it may require you to reboot the system). 

    FP5 along with the latest driver installer and mapping files should already have LTO2 support with the 136T.