I have a PE 2800, which i want to install NT4 on and then upgrade to Win 03. There is no option on the Openmanage cd to install NT.
If i install my NT disc, the screen says inspecting hardware and the the server reboots.
It has a PERC 4e/DC controller
Do i need to update any of the drivers etc.
Thanks
Mohammad
You need to install the F6 drivers for the PERC 4e/Di at the black and white screen where it says detecting hardware on the first boot. You need to hit F6 and install the 3rd party drivers BEFORE it trys to boot or it will blue screen to No hard drive found.
However the Docs say there IS NO NT 4.0 Driver for that perc 4e/Di
I am in the same boat, Have an old NT4 DC that I want to retire. Would like to install NT4 Srv on PE2800 and then restore backup from original DC onto PE2800 and then upgrade to 2003 std. in a test enviornment, then move the new system back into production.
Is there any substitute drivers for the Perc 4e/Di durning the setup other than what was posted? What if I tried the Perc 3Di or something similar?
I am in the same boat, Have an old NT4 DC that I want to retire. Would like to install NT4 Srv on PE2800 and then restore backup from original DC onto PE2800 and then upgrade to 2003 std. in a test enviornment, then move the new system back into production.
Is there any substitute drivers for the Perc 4e/Di durning the setup other than what was posted? What if I tried the Perc 3Di or something similar?
any other suggestions out there?
Regards,
I hate to say this but I did this.
You get a standard IDE Drive and for some its gotta be a HUGE one like 400gig.
If your server isnt that big then you dont need such a big drive.
You then install a Promise UDMA 66/100/133 PCI IDE controller into the server with an IDE DRIVE. HOWEVER this may be a problem as there is now place for the ide drive.
So what you do is this. You make an MSDOS 2 GIG boot partition on the IDE Drive via putting the IDE Drive into a desktop and format the Drive with MSDOS 2GIG FAT PARTITION so that its bootable.
THEN you make a WIN9X Startup Floppy with CDROM SUPPORT.
BOOT FROM THE DISKETTE AND xcopy THE ENTIRE CDROM TO THE C:\ 2GIG PARTITION SO THAT
YOU HAVE AN I386 DIRECTORY ON THE C:\DRIVE
AFTER YOU xcopy D:\ C:\ /e /s /v you have the whole NT CD on the C: Drive.
Then you put the IDE DRIVE into the server attached to the PROMISE IDE PCI card and you steal the power connection from the CDROM DRIVE to POWER THE IDE DRIVE.
BOOT To an MSDOS prompt via the WIN9X starup floppy Or MAKE SURE you have
device=himem.sys and FILES=30 and Buffers=25 and smartdrive.exe running on your msdos
setup.
Then boot and goto C:\I386
Once there type this
WINNT /S:C:\I386 /T:C:\ /B
This will install NT. YOU MUST HAVE AN F6 driver diskette handy for this.
You press F6 when it says detecting hardware and put the NT 4.0 drivers for the promise controller in A: so that it finds the drive.
When it says it wants to install the network SAY NO and put the MICROSOFT loopback connector for the LAN. DO NOT PUT A PASSWORD FOR ADMINISTRATOR just leave it blank and ignore the warning. Make it a workgroup server with no domain. You can add it INTO YOUR DOMAIN as a BDC and then promote it to PDC LATER.
Once NT is installed you need to get a way to have a lan so you must use a 3COM PCI NIC OR some other nic thats compatable that has NT 4.0 drivers. I use realtek 8139 pci nic's cuz they are $9 and work fine. Many new servers nic, chipset and drives are not compatable with NT.
Once you go thru all of this you can update to 2000 or 2003 server and run in emulation mode until you have ANOTHER server as the PDC for your active directory.
All of this dung is so that you dont need to re do all of your file permissions and accounts etc etc.
None of this is supported by dell. NT Requires SP 6.0A for large NTFS partitions.
Theres lots more detail involved but if you don't get what Im saying now you wont get the rest and I dont provide free winnnt to 2000/2003 migration and installation services. If you are willing to pay there are lots of others that can do this for a fee $$$$$$$.
I am in the same boat, Have an old NT4 DC that I want to retire. Would like to install NT4 Srv on PE2800 and then restore backup from original DC onto PE2800 and then upgrade to 2003 std. in a test enviornment, then move the new system back into production.
Is there any substitute drivers for the Perc 4e/Di durning the setup other than what was posted? What if I tried the Perc 3Di or something similar?
any other suggestions out there?
Regards,
I hate to say this but I did this.
You get a standard IDE Drive and for some its gotta be a HUGE one like 400gig.
If your server isnt that big then you dont need such a big drive.
You then install a Promise UDMA 66/100/133 PCI IDE controller into the server with an IDE DRIVE. HOWEVER this may be a problem as there is now place for the ide drive.
So what you do is this. You make an MSDOS 2 GIG boot partition on the IDE Drive via putting the IDE Drive into a desktop and format the Drive with MSDOS 2GIG FAT PARTITION so that its bootable.
THEN you make a WIN9X Startup Floppy with CDROM SUPPORT.
BOOT FROM THE DISKETTE AND xcopy THE ENTIRE CDROM TO THE C:\ 2GIG PARTITION SO THAT
YOU HAVE AN I386 DIRECTORY ON THE C:\DRIVE
AFTER YOU xcopy D:\ C:\ /e /s /v you have the whole NT CD on the C: Drive.
Then you put the IDE DRIVE into the server attached to the PROMISE IDE PCI card and you steal the power connection from the CDROM DRIVE to POWER THE IDE DRIVE.
BOOT To an MSDOS prompt via the WIN9X starup floppy Or MAKE SURE you have
device=himem.sys and FILES=30 and Buffers=25 and smartdrive.exe running on your msdos
setup.
Then boot and goto C:\I386
Once there type this
WINNT /S:C:\I386 /T:C:\ /B
This will install NT. YOU MUST HAVE AN F6 driver diskette handy for this.
You press F6 when it says detecting hardware and put the NT 4.0 drivers for the promise controller in A: so that it finds the drive.
When it says it wants to install the network SAY NO and put the MICROSOFT loopback connector for the LAN. DO NOT PUT A PASSWORD FOR ADMINISTRATOR just leave it blank and ignore the warning. Make it a workgroup server with no domain. You can add it INTO YOUR DOMAIN as a BDC and then promote it to PDC LATER.
Once NT is installed you need to get a way to have a lan so you must use a 3COM PCI NIC OR some other nic thats compatable that has NT 4.0 drivers. I use realtek 8139 pci nic's cuz they are $9 and work fine. Many new servers nic, chipset and drives are not compatable with NT.
Once you go thru all of this you can update to 2000 or 2003 server and run in emulation mode until you have ANOTHER server as the PDC for your active directory.
All of this dung is so that you dont need to re do all of your file permissions and accounts etc etc.
None of this is supported by dell. NT Requires SP 6.0A for large NTFS partitions.
Theres lots more detail involved but if you don't get what Im saying now you wont get the rest and I dont provide free winnnt to 2000/2003 migration and installation services. If you are willing to pay there are lots of others that can do this for a fee $$$$$$$.
I am in the same boat, Have an old NT4 DC that I want to retire. Would like to install NT4 Srv on PE2800 and then restore backup from original DC onto PE2800 and then upgrade to 2003 std. in a test enviornment, then move the new system back into production.
Is there any substitute drivers for the Perc 4e/Di durning the setup other than what was posted? What if I tried the Perc 3Di or something similar?
any other suggestions out there?
Regards,
I hate to say this but I did this.
You get a standard IDE Drive and for some its gotta be a HUGE one like 400gig.
If your server isnt that big then you dont need such a big drive.
You then install a Promise UDMA 66/100/133 PCI IDE controller into the server with an IDE DRIVE. HOWEVER this may be a problem as there is now place for the ide drive.
So what you do is this. You make an MSDOS 2 GIG boot partition on the IDE Drive via putting the IDE Drive into a desktop and format the Drive with MSDOS 2GIG FAT PARTITION so that its bootable.
THEN you make a WIN9X Startup Floppy with CDROM SUPPORT.
BOOT FROM THE DISKETTE AND xcopy THE ENTIRE CDROM TO THE C:\ 2GIG PARTITION SO THAT
YOU HAVE AN I386 DIRECTORY ON THE C:\DRIVE
AFTER YOU xcopy D:\ C:\ /e /s /v you have the whole NT CD on the C: Drive.
Then you put the IDE DRIVE into the server attached to the PROMISE IDE PCI card and you steal the power connection from the CDROM DRIVE to POWER THE IDE DRIVE.
BOOT To an MSDOS prompt via the WIN9X starup floppy Or MAKE SURE you have
device=himem.sys and FILES=30 and Buffers=25 and smartdrive.exe running on your msdos
setup.
Then boot and goto C:\I386
Once there type this
WINNT /S:C:\I386 /T:C:\ /B
This will install NT. YOU MUST HAVE AN F6 driver diskette handy for this.
You press F6 when it says detecting hardware and put the NT 4.0 drivers for the promise controller in A: so that it finds the drive.
When it says it wants to install the network SAY NO and put the MICROSOFT loopback connector for the LAN. DO NOT PUT A PASSWORD FOR ADMINISTRATOR just leave it blank and ignore the warning. Make it a workgroup server with no domain. You can add it INTO YOUR DOMAIN as a BDC and then promote it to PDC LATER.
Once NT is installed you need to get a way to have a lan so you must use a 3COM PCI NIC OR some other nic thats compatable that has NT 4.0 drivers. I use realtek 8139 pci nic's cuz they are $9 and work fine. Many new servers nic, chipset and drives are not compatable with NT.
Once you go thru all of this you can update to 2000 or 2003 server and run in emulation mode until you have ANOTHER server as the PDC for your active directory.
All of this dung is so that you dont need to re do all of your file permissions and accounts etc etc.
None of this is supported by dell. NT Requires SP 6.0A for large NTFS partitions.
Theres lots more detail involved but if you don't get what Im saying now you wont get the rest and I dont provide free winnnt to 2000/2003 migration and installation services. If you are willing to pay there are lots of others that can do this for a fee $$$$$$$.
I am in the same boat, Have an old NT4 DC that I want to retire. Would like to install NT4 Srv on PE2800 and then restore backup from original DC onto PE2800 and then upgrade to 2003 std. in a test enviornment, then move the new system back into production.
Is there any substitute drivers for the Perc 4e/Di durning the setup other than what was posted? What if I tried the Perc 3Di or something similar?
any other suggestions out there?
Regards,
I hate to say this but I did this.
You get a standard IDE Drive and for some its gotta be a HUGE one like 400gig.
If your server isnt that big then you dont need such a big drive.
You then install a Promise UDMA 66/100/133 PCI IDE controller into the server with an IDE DRIVE. HOWEVER this may be a problem as there is now place for the ide drive.
So what you do is this. You make an MSDOS 2 GIG boot partition on the IDE Drive via putting the IDE Drive into a desktop and format the Drive with MSDOS 2GIG FAT PARTITION so that its bootable.
THEN you make a WIN9X Startup Floppy with CDROM SUPPORT.
BOOT FROM THE DISKETTE AND xcopy THE ENTIRE CDROM TO THE C:\ 2GIG PARTITION SO THAT
YOU HAVE AN I386 DIRECTORY ON THE C:\DRIVE
AFTER YOU xcopy D:\ C:\ /e /s /v you have the whole NT CD on the C: Drive.
Then you put the IDE DRIVE into the server attached to the PROMISE IDE PCI card and you steal the power connection from the CDROM DRIVE to POWER THE IDE DRIVE.
BOOT To an MSDOS prompt via the WIN9X starup floppy Or MAKE SURE you have
device=himem.sys and FILES=30 and Buffers=25 and smartdrive.exe running on your msdos
setup.
Then boot and goto C:\I386
Once there type this
WINNT /S:C:\I386 /T:C:\ /B
This will install NT. YOU MUST HAVE AN F6 driver diskette handy for this.
You press F6 when it says detecting hardware and put the NT 4.0 drivers for the promise controller in A: so that it finds the drive.
When it says it wants to install the network SAY NO and put the MICROSOFT loopback connector for the LAN. DO NOT PUT A PASSWORD FOR ADMINISTRATOR just leave it blank and ignore the warning. Make it a workgroup server with no domain. You can add it INTO YOUR DOMAIN as a BDC and then promote it to PDC LATER.
Once NT is installed you need to get a way to have a lan so you must use a 3COM PCI NIC OR some other nic thats compatable that has NT 4.0 drivers. I use realtek 8139 pci nic's cuz they are $9 and work fine. Many new servers nic, chipset and drives are not compatable with NT.
Once you go thru all of this you can update to 2000 or 2003 server and run in emulation mode until you have ANOTHER server as the PDC for your active directory.
All of this dung is so that you dont need to re do all of your file permissions and accounts etc etc.
None of this is supported by dell. NT Requires SP 6.0A for large NTFS partitions.
Theres lots more detail involved but if you don't get what Im saying now you wont get the rest and I dont provide free winnnt to 2000/2003 migration and installation services. If you are willing to pay there are lots of others that can do this for a fee $$$$$$$.
Speedstep, I get what your saying.
Questions: Running NT on the IDE drive... is this temporary while the server runs as a BDC? When you say update to 2003... do you upgrade the IDE drive or do a new install of 2003 to the SCSI drives and remover the promise controller, IDE drive and Realtek NIC?
I have decided to drop the idea of installing NT4 on the PE2800. I hate giving into these things, but the time factor, and management have changed my perspective.
I have a PE2500 that needs to come out of the server farm for additional HDD upgrades and Memory. Since this is a 2000 Server, I will Replace it with the PE2800 and use the PE2500 to install NT4 on then start my migration testing.
I am in the same boat, Have an old NT4 DC that I want to retire. Would like to install NT4 Srv on PE2800 and then restore backup from original DC onto PE2800 and then upgrade to 2003 std. in a test enviornment, then move the new system back into production.
Is there any substitute drivers for the Perc 4e/Di durning the setup other than what was posted? What if I tried the Perc 3Di or something similar?
any other suggestions out there?
Regards,
I hate to say this but I did this.
You get a standard IDE Drive and for some its gotta be a HUGE one like 400gig. If your server isnt that big then you dont need such a big drive.
You then install a Promise UDMA 66/100/133 PCI IDE controller into the server with an IDE DRIVE. HOWEVER this may be a problem as there is now place for the ide drive. So what you do is this. You make an MSDOS 2 GIG boot partition on the IDE Drive via putting the IDE Drive into a desktop and format the Drive with MSDOS 2GIG FAT PARTITION so that its bootable.
THEN you make a WIN9X Startup Floppy with CDROM SUPPORT. BOOT FROM THE DISKETTE AND xcopy THE ENTIRE CDROM TO THE C:\ 2GIG PARTITION SO THAT YOU HAVE AN I386 DIRECTORY ON THE C:\DRIVE
AFTER YOU xcopy D:\ C:\ /e /s /v you have the whole NT CD on the C: Drive.
Then you put the IDE DRIVE into the server attached to the PROMISE IDE PCI card and you steal the power connection from the CDROM DRIVE to POWER THE IDE DRIVE.
BOOT To an MSDOS prompt via the WIN9X starup floppy Or MAKE SURE you have device=himem.sys and FILES=30 and Buffers=25 and smartdrive.exe running on your msdos setup.
Then boot and goto C:\I386 Once there type this
WINNT /S:C:\I386 /T:C:\ /B
This will install NT. YOU MUST HAVE AN F6 driver diskette handy for this. You press F6 when it says detecting hardware and put the NT 4.0 drivers for the promise controller in A: so that it finds the drive.
When it says it wants to install the network SAY NO and put the MICROSOFT loopback connector for the LAN. DO NOT PUT A PASSWORD FOR ADMINISTRATOR just leave it blank and ignore the warning. Make it a workgroup server with no domain. You can add it INTO YOUR DOMAIN as a BDC and then promote it to PDC LATER.
Once NT is installed you need to get a way to have a lan so you must use a 3COM PCI NIC OR some other nic thats compatable that has NT 4.0 drivers. I use realtek 8139 pci nic's cuz they are $9 and work fine. Many new servers nic, chipset and drives are not compatable with NT.
Once you go thru all of this you can update to 2000 or 2003 server and run in emulation mode until you have ANOTHER server as the PDC for your active directory.
All of this dung is so that you dont need to re do all of your file permissions and accounts etc etc.
None of this is supported by dell. NT Requires SP 6.0A for large NTFS partitions. Theres lots more detail involved but if you don't get what Im saying now you wont get the rest and I dont provide free winnnt to 2000/2003 migration and installation services. If you are willing to pay there are lots of others that can do this for a fee $$$$$$$.
Wait a second, how are you supposed to promote a member NT4 server to a BDC/PDC? I thought that's impossible. Don't you have to install it as a BDC to begin with?
I've done NT4 to Windows 2003 upgrades before with Dell PE servers and the worst problems I had was with the built in gigabit nic's. I've never run accross this issue before but IMO since there seems to still be a lot of this going on, Dell should start creating drivers for NT4 on all of their systems for upgrading purposes only. Just create drivers with enough functionality to upgrade to 2000/2003. I do not want to risk upgrading the existing PDC and nor do I have the resources to even attempt to try what you have posted. I will search for NT4 drivers until I find one that will work with this RAID controller. If I don't find one I will have to risk trying to upgrade a 6 year old Compaq server to Windows 2003:(
Louis
Toshiba has AWESOME laptops, but I like Dell's too!
speedstep
11 Legend
•
46969 Posts
287
0
Posted May 12th, 2005 19:00
You need to install the F6 drivers for the PERC 4e/Di at the black and white screen where it says detecting hardware on the first boot. You need to hit F6 and install the 3rd party drivers BEFORE it trys to boot or it will blue screen to No hard drive found.
However the Docs say there IS NO NT 4.0 Driver for that perc 4e/Di
http://support.dell.com/support/edocs/software/svradmin/1.9/en/compgd/8prcmtrx.htm#1064008
LSI Logic MegaRaid SCSI 320-2x is sort of the same kind of controller.
http://www.lsilogic.com/support/download_center/
http://www.lsilogic.com/products/megaraid/megaraid_320_2e.html
However they do not list any such drivers for NT there either.