UNSOLVED

dbrown16

updated

22 years ago

D

dbrown16

7 Posts

0

8723

May 5th, 2005 07:00

PE 4400 running NW5.1 sp7 with critical containers

Hi All,
I have 2 critical containers - details below and have been advised by dell tech support to reseat the offending drives and set each of them as a failover drive. Can anyone advise on whether this can be done using fastcli whilst the server is on line and if so how best to do it - details of the drives below
 

AFA0> disk list                                                        

                                                                       

Executing: disk list                                                   

                                                                       

B:ID:L  Device Type     Blocks    Bytes/Block Usage            Shared  

------  --------------  --------- ----------- ---------------- ------  

0:00:0   Disk            35566478  512         Initialized     NO                            )

0:01:0   Disk            35566478  512         Initialized     NO                              )   18gb drives

0:02:0   Disk            35566499  512         Initialized     NO                            )

0:03:0   Disk            143374650 512         Initialized     NO                  )

0:04:0   Disk            143374650 512         Initialized     NO                  )   73gb drives

0:05:0   Disk            143374650 512         Initialized     NO                  )

                                                                       

 

AFA0> container list                                                

                                                                    

Executing: container list                                           

Num          Total  Oth Chunk          Scsi   Partition             

Label Type   Size   Ctr Size   Usage   B:ID:L Offset:Size           

----- ------ ------ --- ------ ------- ------ -------------         

 0    RAID-5 33.8GB       32KB Netware 0:00:0 64.0KB:16.9GB         

                                                                 0:01:0 64.0KB:16.9GB         

                                                                 0:04:0 64.0KB!16.9GB         

                                                                    

 1    RAID-5  136GB       32KB Netware 0:03:0 64.0KB:68.3GB         

                                                                  --- Missing ---             

                                                                 0:05:0 64.0KB:68.3GB         

                                                                    

 

Thanks in Advance

 

Dave

  • warwizard55

    720 Posts

    262

    0

    Posted May 17th, 2005 23:00

    Hi Dave ,

     

      It looks like you have a problem, your ID 0:2 drive is missing from your Array 0, and your ID 0:4 drive has been rebuilt into ID2's place. The problem is that ID 0:4 is a 73 GB, and ID 0:2 is 18 GB, you have to fix this before you can fix the Array 1 because ID 2 cannot be used in array 1 and ID 4 has lost 18 GB of space so it cannot rebuild into array 1 either.

      Procedure is to remove ID 4, this will cause Array 0 to become degraded.

    Next while the system is powered on, you reseat ID 0:2 and check to see if the drive is rebuilt into the array 0. Using the CLI command: set hotspare 0 (0,2,0) will assign ID 2 to be the hotspare for array 0 should it not start rebuilding on it's own. If it returns an error, or never starts the rebuild, you will need to replace ID 0:2.

    If the rebuild is successful then you reinstall ID4 and issue the command: Set hotspare 1 (0,4,0).

    Note: the delimiters inside the () are commas not colons.

    Warwizard DCSP

  • dbrown16

    7 Posts

    262

    0

    Posted May 18th, 2005 06:00

    Hi Warwizard,

    Thanks for the info - I'll try your solution this weekend and report back - hopefully with a positive result

     

    Thanks again

     

    Dave

  • dbrown16

    7 Posts

    262

    0

    Posted May 23rd, 2005 08:00

    Hi Warwizard,

    I followed the instructions running the command container set failover 0 (0,2,0) to set up the hotspare drive

    Nothing much seemed to happen after this, so I ran disk zero 2 followed by disk initialize (0,2,0)

    Now the "drive online indicators on drives 0 & 1 blink rapidly  indicating logical drive is rebuilding but on drive 2 the drive online indicator is on steady

    Do I need to replace drive 2
     
    Thanks in Advance
     
    Dave