
UNSOLVED
Port-Channel on 3548P
Hi All,
Having some issues connecting my 3548P to my Cisco 3750 via a port channel. The port channel on the dell keeps flaping.
Cisco config as below (not all config):
spanning-tree mode pvst
no spanning-tree optimize bpdu transmission
spanning-tree extend system-id
spanning-tree uplinkfast
spanning-tree backbonefast
spanning-tree vlan 101,109-110,120,130,140,150,160,170,200 priority 0
interface Port-channel3
description EtherChannel to Ground Floor 2950 48 Port Switch
switchport trunk encapsulation dot1q
switchport mode trunk
interface GigabitEthernet1/0/5
description Connection to Ground Floor 2950 48 Port Switch
switchport trunk encapsulation dot1q
switchport mode trunk
priority-queue out
channel-group 3 mode on
interface Vlan1
ip address 172.16.2.1 255.255.254.0
interface Vlan120
description Network Management
ip address 172.16.1.9 255.255.255.0
!
interface Vlan130
description Civic Tower Level G
ip address 172.16.13.1 255.255.255.0
ip helper-address 172.16.2.29
ip helper-address 172.16.2.22
ip directed-broadcast 176
Dell Config As below:
interface port-channel 3
exit
interface range ethernet 1/e(1-48)
spanning-tree portfast
exit
interface port-channel 3
speed 1000
exit
interface range ethernet 1/g(3-4)
description Link_to_TWR3750STACK
exit
interface port-channel 3
exit
interface port-channel 3
switchport mode trunk
exit
interface range ethernet 1/g(3-4)
switchport mode trunk
exit
vlan database
vlan 120,130
exit
interface port-channel 3
switchport trunk allowed vlan add 120
exit
interface range ethernet 1/e(1-48)
switchport access vlan 130
exit
interface port-channel 3
switchport trunk allowed vlan add 130
exit
interface vlan 120
name Management
exit
interface vlan 130
name "Level 1"
exit
voice vlan oui-table add 0001e3 Siemens_AG_phone________
voice vlan oui-table add 00036b Cisco_phone_____________
voice vlan oui-table add 00096e Avaya___________________
voice vlan oui-table add 000fe2 H3C_Aolynk______________
voice vlan oui-table add 0060b9 Philips_and_NEC_AG_phone
voice vlan oui-table add 00d01e Pingtel_phone___________
voice vlan oui-table add 00e075 Polycom/Veritel_phone___
voice vlan oui-table add 00e0bb 3Com_phone______________
interface range ethernet 1/g(3-4)
channel-group 3 mode on
exit
interface vlan 120
ip address 172.16.1.50 255.255.255.0
exit
interface vlan 1
ip address 172.16.3.101 255.255.254.0
exit
interface vlan 130
ip address 172.16.13.2 255.255.255.0
exit
ip default-gateway 172.16.1.9
qos trust dscp
hostname SW3548P_GF
logging 172.16.2.228 severity warnings
logging buffered warnings
logging file warnings
aaa authentication enable default line
aaa authentication login default line
power inline usage-threshold 90 unit 1
power inline traps enable unit 1
no snmp-server trap authentication
snmp-server community bcc_private rw 172.16.2.228 view DefaultSuper
snmp-server community bcc_public ro 172.16.2.5 view Default
snmp-server community bcc_public ro 172.16.2.228 view Default
ip https exec-timeout 15
clock timezone +10
ip name-server 172.16.2.29 172.16.2.22
asset-tag 5325 unit 1
Default settings:
Service tag:
SW version
Fast Ethernet Ports
==========================
no shutdown
speed 100
duplex full
negotiation
flow-control off
mdix auto
no back-pressure
Gigabit Ethernet Ports
=============================
no shutdown
speed 1000
duplex full
negotiation
flow-control off
mdix auto
no back-pressure
interface vlan 1
interface port-channel 1 - 15
spanning-tree
spanning-tree mode STP
qos basic
qos trust cos
Any ideas guys? vlan's match on both. Maybe spanning tree settings?
Thanks
John
Responses (5)
Solutions (0)
There are two ports setup on the Cisco 3750 (2 switches setup as a stack). One port on each switch.
Flapping: On the dell switch ports g3 and g4 once plugged in just go up and down etc
I can't pass any traffic from the dell to the cisco.
Thanks
Reply You have the 3548 in stacking mode. When it is in stacking mode, ports g3 and g4 are used for stacking, not for Ethernet.
If you want to use g3 and g4 for Etherent, you need to put the switch in standalone mode. This means using the "select" button during boot to set the "stack id" LEDs to all off.
Reply

bh1633
909 Posts
822
0
Posted August 26th, 2009 08:00
The port-channels look like they are set up correctly on both.
What do you mean by "flapping"? How is this observed?
How many Cisco switches are connected to the 3548P?
I only see one port on the Cisco configured in port-channel 3 but there are 2 in the Dell. Can you post the entire Cisco config?