UNSOLVED

chewondave

updated

21 years ago

0

5365

July 11th, 2005 18:00

Important Suggestion for those with the "DVI Power Saving Mode" problem w/ nvidia cards!

Before you think this is the same thing as the DVI "power saving mode" issue with Dell screens and Nvidia cards that is below:
 
keep on reading.
 
Many haven't gotten the file http://www.jeffgeiger.com/cgi-bin/ikonboard.cgi to work properly, while indeed the file does work. I hope the following tip will help you get your DVI  up and running again.
 
There is no need to disconnect power cables, turn off your screen etc. etc. This is all you have to do.
 
Download the file. Unzip it. Insert a floppy disk. Run "DVI_recover_floppy". This will create a bootable file on the floppy disk that will resolve the issue. Turn off the computer, you can leave the analog cable and dvi cable both connected. The key point is here: enter "Setup" by pressing F2 while the computer is booting up. When the BIOS is on screen, navigate to "Boot". Make the 1st item to boot your floppy drive. Now "Exit and Save" by pressing F10. Turn off your computer (power button), and turn it on again. You should hear your floppy drive being accessed. If your analog cable is in, wait, you should see that you are entering MS-DOS. then you will  see first one line of "A://somefilename...etc...." and then a short while later, a second line of "A://somefilename...etc..." Finally you should see a third line, simply " A:// " and your floppy drive should be silent. Once the floppy driver is no longer being accessed, you can now turn off your computer, and turn it back on again. Your DVI should be up and running. But wait, there's more, you need to enter "Setup" again and make your primary hard drive the 1st to boot up again. Now you should be all set!
 
I hope this helps some of you resolve this problem!
                David

Message Edited by chewondave on 07-11-2005 03:00 PM

Message Edited by chewondave on 07-11-2005 03:00 PM

  • cliff27

    21 Posts

    528

    0

    Posted July 11th, 2005 19:00

    I have never been able to get DVI fo work at all with my NVIDIA 5200 card. I only get, as I recall, Digital Input and something.... It does work in analog. It is not a matter of working and then going into powersave although the lite does turn from green to amber. Should this fix my problem? Also, I do not have a floppy drive...Finally, not sure what you mean by entering "setup" again?

    Thanks!
  • 528

    0

    Posted July 11th, 2005 20:00

    Yes, the problem you describe is the one adressed here. I even have the same video card as you do! *edit* I also see your last 1231098479371024 posts have been about it. Frustrating isn't it when DVI doesn't work like it should!?!! I know I was *end edit*
     
     If you do not have a floppy drive, you will have to still download that file from that link, but this time you need to burn the "DVI_recover_CDIMAGE.iso" onto a CD. The following describes the process:
     
    "If you do NOT have a floppy drive, you will need to burn the ISO image DVI_Recover_CDIMAGE.iso onto a CD-R or CD-RW disc. The procedure for this varies from software to software. In most cases, your software will have an option for "Burn Image" or "Write Disc from Image," which you will choose. Ensure the software is looking for .iso files, browse to the location that you extracted the files from the DVI_Recover.zip to, select the file DVI_Recover_CDIMAGE.iso, and complete the image burning process. If your installed software does not have image burning capabilities, the Demo version of Nero 6 may contain that functionality." - quoted from DELL-Cody - from: http://forums.us.dell.com/supportforums/board/message?board.id=dim_monitor&message.id=33887

     
    Now the steps are the same as I described before, only this time your cd drive must be the first to boot.
     
    To enter "Setup", press "F2" immediately after turning on your computer. This will allow you to access your boot-up settings. It is a blue backgrounded screen; use the arrow keys to navigate (this is very clearly described once you are in Setup, you should have no problems) I do not know if this is universal, but for me, you use the right arrow key to go to the menu "boot". Depending on how many drives harddrive;cd-r/rw, you have it will show you something roughly like this
     
    1st (some words....)        nameofdrive1
    2nd (some words....)       nameofdrive2
    3rd (some words...)         nameofdrive3
     
    Pretend nameofdrive3 is the cd drive you have the CD w/ file. Using the down arrow keys now, navigate until "nameofdrive1" is hilighted. press enter. A small menu should appear, now use the arrow keys to hilight drive 3. Press enter. It should now have as the first line:
     
    1st (some words....)        nameofdrive3
     
    Overall you shouldn't have any problems navigating BIOS. The instructions are very clear, located on the right side column that is always present in BIOS. If you have any other questions feel free to ask
     
     

    Message Edited by chewondave on 07-11-2005 04:15 PM

    Message Edited by chewondave on 07-11-2005 04:22 PM

  • cliff27

    21 Posts

    528

    0

    Posted July 11th, 2005 20:00

    Thanks...will give it a go
  • DJ_ShiSaS

    182 Posts

    528

    0

    Posted July 11th, 2005 22:00

    it could be also (and is really stupid) that the dvi and vga cables are connected both, you should only connect one at the time
  • 528

    0

    Posted July 12th, 2005 00:00

    Actually for me connecting both analog and DVI at the same time wasn't a problem at all, though it may be for other people. You may be right that it is indeed bad though, I have no idea!
  • glassman7

    1 Message

    528

    0

    Posted July 12th, 2005 06:00

    After two weeks of hassle with Dell tech support  ( Ireland) with this DVI power save problem this fix worked. In under five minutes I was up and running once again. Excelllent work  to all those concerned 
  • reddice

    2 Intern

    •

    197 Posts

    528

    0

    Posted July 14th, 2005 23:00

    When I got my FX550 card and I first connected DVI it was not working giving me a black screen with some message which I don't remember and then the desktop just appeared. I then installed the latest video drivers and it is working.