UNSOLVED

Geedsen

updated

18 years ago

G

Geedsen

10 Posts

0

41597

October 5th, 2008 16:00

raid 1 on T7400

I just closed another topic about setting up a raid 1 system disk.

 

Currently I have in my system 2 SAS disks and 2 SATA disks, all on the LSI controller.

 

The two SAS disks are in raid 1 as system disk. The 2 SATA disks are in raid 1 and data disks.

 

The state of the SATA raid is resyncing (because one disk had a cable disconnected when I was working on the duplication of the original system disk).

 

The system boots normal, but after some time popup dialogs (several) with the following message:

 Controller ID:0 PD removed:0:3

 

At the same time I do hear some clicking sounds coming from the PC.

 

The event log shows this:

 

Controller ID: 0 Link lost on SAS wide port: 2 = 3 .

Controller ID: 0 State change on VD: 2Previous = Degraded Current Offline .

Controller ID: 0 PD removed:0:3 .

Controller ID: 0 Link restored on SAS wide port: 2 = 3 .

Controller ID: 0 State change: PD= 0:3 Previous = FailedCurrent = Offline .

Controller ID: 0 State change on VD: 2Previous = Offline Current Degraded .

Controller ID: 0 SAS/SATA mixing not supported in enclosure; disabled PD:0 .

Controller ID: 0 PD inserted:0:3 .

Controller ID: 0 Link lost on SAS wide port: 2 = 3 .

Controller ID: 0 Link restored on SAS wide port: 2 = 3 .

Controller ID: 0 State change on VD: 2Previous = Degraded Current Offline .

Controller ID: 0 PD removed:0:3 .

Controller ID: 0 State change: PD= 0:3 Previous = FailedCurrent = Offline .

Controller ID: 0 State change on VD: 2Previous = Offline Current Degraded .

Controller ID: 0 SAS/SATA mixing not supported in enclosure; disabled PD:0 .

Controller ID: 0 PD inserted:0:3 .

All these events with a timeframe of 1 minute after the eventlog started.

 

What is happening?

 

'SAS/SATA mixing not supported in enclosure'

 

According to the manual it is supported,as long as you don't mix within the raid itself.

 

 

 

  • Geedsen

    10 Posts

    513

    0

    Posted October 5th, 2008 21:00

    Hoping that it would solve my problem, I tried to update the firmware for the controller.

    Unfortunately I have been unable to create a bootable cd to get a dos prompt. Can anyone tell me how to do it. I tried using nero and partpe. Both cd's boot but hang after a few lines of execution. Anyone managed to do this (either creating a bootable cd or flash the controller)?

     

    Thanks

     

  • drno007

    11 Posts

    513

    0

    Posted October 6th, 2008 13:00


    @Geedsen wrote:
    At the same time I do hear some clicking sounds coming from the PC.

     


    This sounds to me like one of your drives has gone bad. Kaputt.

    Download ultimatebootcd and boot the computer off of that or use Dell System diagnostics to check your drives.

     

    download dell diag or ultimatbootcd

     

    Start with Dell diag.

  • Geedsen

    10 Posts

    513

    0

    Posted October 6th, 2008 17:00

    I don't think so. It's a controller problem. When I left the SATA in raid 1 and removed the SAS raid , everything is fine. It looks like mixing an SAS raid1 and a SATA raid 1 does not work.

     

     

    I just tried to google a topic I found in a forum, that was related to the 5/i controller. That the controller can not handle the mix , that it looks like it is working, but the controller get's flaky. Unfortunately I cannot find it anymore. Seems that that is true for trhe 6/i as well.

     

     

  • Geedsen

    10 Posts

    513

    0

    Posted October 15th, 2008 08:00

    Dell support tells me that Dell has no computer with controllers that support 2 raid arrays on one controller.

    I think that is bogus, but cannot find hard evidence that it is. Any link to the contrary would be appreciated.

    The BIOS of the controller let you create and manage multiple arrays.

     

    Ben