UNSOLVED

Snoods

updated

18 years ago

S

Snoods

29 Posts

0

8867

July 24th, 2008 10:00

Memory Question

I have now got the correct memory chips (had incorrect ones previously) and i supposedly have 2 X 2GB PC2 6400 800Mhz chips. Windows shows the correct memory fine 4GB.

 

What is the best mode to run them in my XPS 420. They work in single configuration or in both the white sockets in dual mode.

 

The thing i don't understand is that CPUID reports them as 400Mhz no matter what config i have them in and my Vista memory score has gone down from 5.4 to 5.0.

 

Any ideas why? My previous memory was 2 X 1GB and 2 X 512MB giving 3 GB They were all PC2 5300

 

Sorry if they are silly questions but i'm not very up on Memory speeds and configurations. 

Message Edited by Snoods on 07-24-2008 06:51 AM
Message Edited by Snoods on 07-24-2008 06:52 AM
  • ejn63

    11 Legend

    •

    87469 Posts

    •

    321256 Points

    212

    0

    Posted July 24th, 2008 10:00

    They do run at 400 MHz.  DDR means double data rate - the effective throughput is twice the speed.  In other words, DDR-2 800 (PC2-6400) does run at 400 MHz.

     

  • Snoods

    29 Posts

    212

    0

    Posted July 24th, 2008 10:00

    Ah yes that does make sense ejn63, thanks for that. So single or dual mode any difference using either method ?
  • Snoods

    29 Posts

    212

    0

    Posted July 24th, 2008 11:00

    Just as a side note, my Vista memory rating returned to 5.5 in dual mode so all is well. I know it's not really important but it looks better LOL
  • Davet50

    6 Operator

    •

    14442 Posts

    212

    0

    Posted July 24th, 2008 11:00

    Yea i know what you mean. I gave up on the scores a while ago. I have the same system as another user with the same ram and he gets 5.9 for his ram and I only get 5.8..go figure. :smileyvery-happy:

     

    Message Edited by Davet50 on 07-24-2008 08:39 AM
  • Snoods

    29 Posts

    212

    0

    Posted July 24th, 2008 11:00

    Perhaps you have a couple of slightly grubby pins, you should take out your chips and give them a nice polish. :smileyvery-happy:
  • Davet50

    6 Operator

    •

    14442 Posts

    212

    0

    Posted July 24th, 2008 11:00

    You must "pair" the memory. So it should be installed into slots 1 and 2 and another pair in slots 3 & 4. this will allow the memory to be run in dual channel mode, which is the fastest way for the memory to work.

     

    CPU-z will always report 800 mhz at 400 and 1066 at 533 and so on because the memory is dual bandwith.(not ot be confused with dual channel two differnt things.) So you multiply the freq by 2 so 400 X 2 = 800.

     

    Vista scores are extremly overrated and I would not pay much attention to them by the way are you mixing the  memory or just running with the single speed. If you mix the  PC 5300 and the PC6400 then all the memory will run at the slowest speed, PC5300

  • Snoods

    29 Posts

    212

    0

    Posted July 24th, 2008 11:00

    Thanks Dave i will change the chips back to Dual mode then, and no i have the other memory chips out and just sticking to the 2 X 2GB chips.

     

    Many thanks to you both for clarifying things. I'm quite happy now.