wfbauerle

updated

14 years ago

W

wfbauerle

8 Posts

0

113146

September 6th, 2012 12:00

Dell Precision T7400 Workstation will not power up with ATI Radeon 5970 installed

Hello,

I got my dream video card, the ATI Radeon 5970 Dual GPU monster and installed it in my T7400 however the system will not boot up, all I get is a quick spin of the fans and some sort of sound coming out of the power supply, kind of like "Brrrnt, click" which led me to believe that the PSU couldn't handle my video card.

The video card requires both an 8pin and 6pin power plug. When I plug in the 8 pin, and the 6 pin and power up the computer, it's a no-go as above. when I plugged in only the 6-pin power plug the PC sounds like it will boot, the fans power up but no display as I would expect.

I have tried this video card in both PCI-Express slots with the same failure as the result. The computer works fine with the Nvidia Quadro 3700 in it...using one 6pin power connector.

I took the ATI Radeon HD 5970 video card to a local computer store and had it tested ($15) since I didn't have a spare computer to test it in and the video card passed with flying colors...

Therefore I figured that my 1000 watt power supply had a problem, so as a gamble, I ordered a replacement off eBay and received a working pull plus the wiring harness and totally replaced both which was a job to say the least!! Have you ever tried replacing the wiring harness? lots of work...

I got it all back together, crossed my fingers and prayed and tried it again and the same thing.. NO LUCK... I put the Nvidia Quadro 3700 back in and the system powered up like a charm.

What on earth could it be causing this to happen? I REALLY want to get this video card working in this system...

I even tried a bios update and thoroughly looked at the motherboard and everything I could to see if there was any popped capacitors.. nothing...

PLEASE HELP - I want to get my gaming on...

Wesley :emotion-9:

  • wfbauerle

    8 Posts

    2320

    1

    Posted September 9th, 2012 15:00

    I think I found the solution and I'd like to mention it here to help others if they search for it..

    A: The Dell power supply for the T7400 was designed to have five 12 volt rails @ 18 AMPS each and the video card requires about 45 to 50 amps to work correctly. The video power cables (the one with an 8pin and 6pin both on the same harness) seems to only provide 18 or so amps and the computer will not power up because the power supply's protection circuit sees too many amps being drawn from one "rail" and immediately shuts off..

    I went to Fry's Electronics in San Jose and bought a couple adapters that helped me split the current draw between different sources, such as the Hard Drive cables and the video cables.

    B: I have a small battery backup power unit and my T7400 was plugged into the backed-up portion.. when I got the video card to work, it would make a loud beep and after a few minutes cut power to my T7400 due to large current draw.. I plugged the computer into a "Surge Protected" but not battery backed up slot and since then have had no problems..

    Now after multiple stress tests including FurMark, my graphics card is working great in this system.. It is due to an unfortunate design in the T7400 power supply and cabling.. Now that I have this resolved I hope someone else can benefit..

    Get an adapter like this, use it to split the power sources for the 8 pin power connector and use the original 6 pin that is connected to the Dell provided 8 pin adapter, for the 6 pin slot... hope that makes sense... through trial and error you will get it right! :emotion-5:

    I got one like this:

     

  • rayhem

    1 Message

    2320

    0

    Posted March 15th, 2013 20:00

    What kind of adapter did you get? It doesn't seem to be showing up...

    I was looking to upgrade my graphics as well and want to make sure that everything will work fine.

  • styleruk

    13 Posts

    2320

    0

    Posted May 2nd, 2013 04:00

    Hi, I'm up against this now.  I have just got two AMD geforce 6970 and tried to set up one last night.  I'm going to get a connector to take power from both my spare sata cables, my only thought is that would there be enough power in these drives to power the cards?

    each card will then have 6pin from normal harness + 8 pin coming from two sata plugs joined on same cable.

    I'll let you know.

    PS:  adaptor here or ebay...

    uk.startech.com/.../6in-SATA-Power-to-8-Pin-PCI-Express-Video-Card-Power-Cable-Adapter~SATPCIEX8ADP

  • demolishia

    1 Message

    2320

    0

    Posted March 6th, 2014 01:00

    Hi styleruk,

    Did you manage to get your graphics card to work? I've recently bought the Nvidia GTX 760 which also has an 8 pin and 6 pin connectors and I had the same issue. Did you manage to supply the card with enough power using the adapters?