UNSOLVED

Dan_Honemann

updated

21 years ago

0

10987

December 26th, 2005 11:00

8250 replacement mobo causes SCSI card timeout error

I swapped motherboards in my 8250 (with an identical board) and now my Adaptec 2906 (Adaptec 7850 chipset) PCI SCSI card won't work. It takes forever for Windows XP (SP2 with all the latest patches and the latest drivers for the card) to boot and the Event Viewer System Log shows several Event ID 9 errors: timed out waiting for aic-78xx.sys to respond. Oddly, Win XP never showed the systray bubble saying it found the new hardware... but the entry is in Device Manager and the IRQ shows no conflicts. I tried hooking up my scanner to it and it doesn't work, however.

I know the card is good as I just installed it on another PC and it works fine.

I have tried re-installing windows (even on a brand new hard drive) inserting the card just after installing all drivers and I still get the same problem, which tells me the issue is either with the BIOS or some jumper/setting or flash ram on the motherboard. I've tried using each of the PCI slots--same problem with all of them.

I doubt it is the BIOS (I'm on A04 which is the latest for the 8250) but will try to reset it, although I have yet to figure out how to do that on the 8250 (it seems to involve having to set a Maintenence jumper on the mobo for some reason). I have already tried switching IRQ's in the BIOS system setup, to no avail.

I could also try resetting the NVRAM, although I'm not sure what that does.

Basically, I'm at a loss and would deeply appreciate any help you could send my way on this.

Thanks,
Dan

P.S. Does anyone know how to set the maintenance jumper on the 8250 mobo in order to access the Advanced section of the BIOS settings in order to reset to factory defaults? Are there any other switches on the mobo that would affect PCI slots and thus the card?

Message Edited by Dan_Honemann on 12-26-2005 08:33 AM

  • BigBrother

    2 Intern

    •

    4801 Posts

    156

    0

    Posted December 26th, 2005 11:00

    Dan_Honneman,

    There are settings in system setup (BIOS) which will affect the way a system boots up.  You can go into system setup (BIOS) and modify the boot order to put the floppy drive first, the hard drive second, the CD drive 3rd and (if the option exists) put the "bootable add-in cards" last.  This would put your SCSI card later in the boot order than the other devices.  Your system should boot to the hard drive before it even sees the SCSI card. 

    Resetting your BIOS to factory defaults will set the boot order to the original settings.  You can do this by entering system setup using teh key at system startup.  When in system setup, press the CapsLock, NumLock and ScrollLock keys, and to light up all three on your keyboard.  Then press CTRL-E and the system will beep at you.  This beep will indicate that the system BIOS has been restored to factory defaults.

    Resetting your BIOS to factory defaults may very well resolve your issue.  And, as suggested by Osprey4, updating your BIOS to the latest version should also prove useful.

    Steve

    Message Edited by BigBrother on 12-26-2005 08:37 AM

  • osprey4

    6 Operator

    •

    34230 Posts

    156

    0

    Posted December 26th, 2005 11:00

    The first thing I would try is to check if the BIOS is current and if not, to update it.
  • BigBrother

    2 Intern

    •

    4801 Posts

    156

    0

    Posted December 26th, 2005 12:00

    Dan_Honneman,

    The message board stripped out the keystroke references in my post.  I guess that you cannot use "<" and ">" in a post.  I have changed the post so that it is readable.  To reset BIOS defaults, enter system setup using the F2 Key press the NumLock, CapsLock and ScrollLock keys to light up those lights on your keyboard.  Then, press CTRL-E and your system will beep at you.  This beep will indicate that the system setup has been reset to factory defaults. 

    There are no jumpers on the motherboard which will affect IRQ assignments for PCI cards.  You can, however, affect the way PCI cards are queried by installing them in specific slots.  Check this link:

    http://support.dell.com/support/edocs/systems/dim8250/techov.htm#1106006

    If you choose to re-configure your PCI card placements, remove them all, reset system defaults and then reinstall them.

    Steve

  • 156

    0

    Posted December 26th, 2005 12:00

    I already am on A04 which is the latest BIOS, so unfortunately this is not the problem.

    BigBrother's message on how to reset the BIOS seems to be missing all the keys I'm supposed to press :(. Or is it that I can't view them using my Firefox browser?

    Just to be clear: the SCSI card is not attached to any drives... it isn't a boot issue. It just does not work at all on this mobo but worked fine on my prior mobo (same 8250 one, but I swapped due to other problems with the first one) and works fine in another PC.

    I notice it shares an IRQ with the network card and several USB controllers. I would like to get it to its own IRQ but of course windows APCI makes this impossible. Even when I reinstalled Windows with nothing in the PC but the video card and added the SCSI card next, it still gets assigned an IRQ that is shared with USB controllers.

    When I install it in a Compaq PC, it gets IRQ 17 all to itself.

    Finally, are there jumpers or settings on the 8250 mobo that can affect PCI cards?

    Thanks again,
    Dan
  • BigBrother

    2 Intern

    •

    4801 Posts

    156

    0

    Posted December 26th, 2005 13:00

    Dan_Honemann,

    Forge ahead.  There is no need to start over. 

    Steve

  • 156

    0

    Posted December 26th, 2005 13:00

    Resetting the BIOS did the trick!

    Thank you so much!!

    Since I am early on in my re-installation process, should I go back from square one and reformat the drive, etc., at this point--or is it safe to proceed from here (all I have done is partitioned, formatted the new drive, installed all the basic drivers (chipset, video, audio, ethernet), and now installed the SCSI card)?

    Dan