cones72

updated

9 years ago

C

cones72

9 Posts

0

3613

March 11th, 2018 05:00

Insprion 7773 and Samsung 960 EVO NVME SSD

Hello,

  I have an Inspiron 7773 with a Micron 1100 SSD (512GB, SATA3, 2.5inch).  I bought a Samsung 960 EVO 1TB NVME SSD.  It installed fine and I can see it under "System Configuration" in BIOS.  Windows found it fine and I ran the Arconis disk cloning software (Samsung's never has worked for me in the past so I use Arconis).  Anyways, the disk cloned fine but upon reboot the drive doesn't show up under UEFI boot options.  Is there a BIOS "issue" with Samsung NVME SSD's or am I doing something wrong?

  • cones72

    9 Posts

    3327

    0

    Posted March 12th, 2018 20:00

    It turns out it was the cloning software (all three I tried).  None of them were setting the boot flag on the boot partition.  I did a clean install of windows 10 on the 960 EVO and it booted up fine.  I'm still in the process of porting apps and some files over (itunes songs).  A very frustrating experience.  I wish windows had a porting app similar to what the Apple Mac has (which is very painless and "just works").  Thanks for the suggestions.

  • ejn63

    12 Elder

    •

    31849 Posts

    •

    156277 Points

    3370

    0

    Posted March 11th, 2018 06:00

    Did you shut down immediately after cloning, and remove the 2.5" drive before booting for the first time?

     

  • cones72

    9 Posts

    3353

    0

    Posted March 11th, 2018 15:00

    Yes.

  • jphughan

    11 Legend

    •

    13985 Posts

    •

    79931 Points

    3344

    1

    Posted March 11th, 2018 16:00

    Can you boot from the SSD by accessing the F12 boot menu.  In UEFI mode, the BIOS interface doesn't just list every boot device it detects there.  Boot options that reside on storage devices like hard drives and flash drives (as opposed to optical media and network) actually have to be registered into the UEFI firmware to be listed there, which is something that Windows Setup does during typical installations and that some cloning applications will do as well.  However, the F12 one-time boot menu DOES list every boot option that it detects, so if you can see and boot from your SSD that way, you can try using the "bcdboot" command within Windows to perform that registration.  You should be able to find Microsoft's documentation for how to use that command if you Google that name, but you'll also need to know how to use diskpart to temporarily assign a drive letter to your EFI partition.

    Alternatively, you can try rerunning the clone with another application, like Macrium Reflect Free, which will handle this all for you.  Worst case after the clone you'd have to run its "Fix Boot Problems" function in the Rescue Media environment after the clone.  You might also have to either make sure your the SATA Operation setting in your BIOS is set to RAID rather than AHCI, or else install the Samsung NVMe driver before performing the clone.  You cannot do both.  The reason is that when moving Windows from a SATA device to NVMe, it will sometimes not boot because the Windows installation you cloned won't have ever been set up to load its NVMe class driver, which will prevent it from booting from an NVMe device.  Installing the Samsung driver beforehand definitely avoids that issue, and having the system in RAID mode also avoids it because in the latter scenario, the NVMe interface is abstracted by the Intel RST controller.  A third option specific to Macrium Reflect is to use the ReDeploy interface to tweak the Windows installation to load its NVMe class driver, but ReDeploy isn't part of the free version.

  • ejn63

    12 Elder

    •

    31849 Posts

    •

    156277 Points

    3351

    0

    Posted March 11th, 2018 16:00

    Next thing:  is the system in AHCI mode (NOT RAID)?

     

  • jphughan

    11 Legend

    •

    13985 Posts

    •

    79931 Points

    3308

    0

    Posted March 13th, 2018 07:00

    Apple benefits from controlling both the software and hardware platform, which allows it to offer solutions like Time Machine that aren't entirely feasible for Microsoft or any single PC vendor to offer.  But I gave you two solutions above for working around the issue of the NVMe driver not being loaded above: either install the Samsung NVMe driver beforehand or use the paid version of Macrium Reflect to get access to ReDeploy, which might have been worth it just for the time savings.  But ok, glad you worked something out.