I just received my XPS 13 9310 and connected it with the WD19 station. The screen is a Dell S2721QS 4K.
It is impossible for me to have a display in 4K at 60Hz, I only have 30Hz with this station. I tried to connect the screen with an HDMI or DisplayPort cable, same result.
When I use the DA300 station, I have an image in 4K at 60Hz.
All drivers are up to date.
Do you have a solution to have 4K at 60Hz with the WD19?
@Rino07 The XPS 13 supports DisplayPort 1.4/HBR3 over USB-C. The Display Resolution Table for HBR3 systems found in the WD19 User Guide on support.dell.com specifically says that 4K 60 Hz is possible -- but only with HBR3 systems. But that display would have to be the only one connected. If you have another display as well, then there won't be enough bandwidth to run 4K 60 Hz plus something else. If that's the only display and you're still having trouble, make sure you've updated the firmware of the WD19 and the BIOS of your system. If you've already done that, then unfortunately this may be a firmware glitch on one side or the other. I remember when the XPS 13 9300 was released, there were firmware glitches that caused it not to be able to run dual 4K 60 Hz displays through a WD19TB (which should have been possible) and for a while there was a BIOS bug that caused it not to work at all with a wide range of simple USB-C to DP/HDMI adapters. So this might be something that will require an update that might not exist yet, unfortunately.
Hi, Thanks for your answer. Yes I have only one display connected (I had also a XPS 13 9370 and it was working properly). The WD19 and my new XPS are up to date. The strange point is that it works in 60 Hz with a D300 station but not with the WD19. I hope DELL will fix this issue soon.
@Rino07 When you mentioned the D300 station, did you mean D3000? If so, that is a completely different type of dock. It does not tap into actual GPU outputs and instead uses “indirect display” technology called DisplayLink — not to be confused with DisplayPort. And DisplayLink can have quite a few drawbacks in certain use cases compared to the “normal” method of using actual GPU outputs like the WD19 does. That doesn’t explain why the WD19 doesn’t work properly in this case of course, but the D3000 is a completely different type of setup.
Any idea when this will be resolved? I'm having the same problem with the HP G5 dock (which is equivalent to the WD19 but from HP). Is that a problem with the XPS firmware or with the Intel drivers?
jphughan
11 Legend
•
13985 Posts
•
79931 Points
1461
0
Posted December 16th, 2020 06:00
@Rino07 The XPS 13 supports DisplayPort 1.4/HBR3 over USB-C. The Display Resolution Table for HBR3 systems found in the WD19 User Guide on support.dell.com specifically says that 4K 60 Hz is possible -- but only with HBR3 systems. But that display would have to be the only one connected. If you have another display as well, then there won't be enough bandwidth to run 4K 60 Hz plus something else. If that's the only display and you're still having trouble, make sure you've updated the firmware of the WD19 and the BIOS of your system. If you've already done that, then unfortunately this may be a firmware glitch on one side or the other. I remember when the XPS 13 9300 was released, there were firmware glitches that caused it not to be able to run dual 4K 60 Hz displays through a WD19TB (which should have been possible) and for a while there was a BIOS bug that caused it not to work at all with a wide range of simple USB-C to DP/HDMI adapters. So this might be something that will require an update that might not exist yet, unfortunately.