Yet another 'hard drive not found' - but with a twist?
Most of the message I sent to Dell -
Problem Description: 'Invalid configuration information, please run setup program 'Primary Hard drive not found 'Fixed optical disk not found 'No bootable devices detected'
After battling phone-based tech support and seeking other help on the forums, I've already been through several changes in status. First, I turned on my computer and recieved only a primary and optical drives not found message. After a computer tech looked at my hdd and motherboard for signs of shorting (found none) and replaced all removable parts, loud clicking noises emitted from the hdd. Immediately after, the screen size diminished. We phoned tech support and determined the problem to be along the lines of a faulty ide controller. Later, as I was reading the forums on this particular issue, I read that the problem was due to the optical disk. Since we hadn't removed that component since the hdd began taxing again, I shut off the power and removed the optical disk. This was when I recieved the invalid configuration message. I'm once again at my wit's end and I refuse to pay the $1100 that dell is asking to repair my motherboard. I'm starting college in less than a month and I simply do not have the money to spend the cost of ANOTHER full computer for one component. Please, please help me! I've noticed this to be a common problem on the forums - especially with people out of warranty, like myself. The computer tech I'm working with is theorizing that the motherboard battery might be dead, and asks where the power source for the CMOS is located (on the battery or an internal lithium cell?).
There's -yet another- change in my status. After running the BIOS-based hard drive diagnostic, the optical drive was found, but the hard drive continues to not work. The hard drive still taxes and now beeps loudly. It is also warm when removed.
When we attempted to boot from a Windows XP CD, the optical drive magically dissappeared and will not return, even when diagnostic was run again. It would've been nice for phone support to have told me about the diagnostic, but I guess that's too much to ask.
[Isn't it great how things break when out of warranty? Was everyone else informed when their warranty expired, because I can't remember it happening. I feel like I've been scammed.]
When you pull the fixed disk and get the config error, hit F2 (I believe) and get into the BIOS, then exit and boot normally and see if the hdd works better.
Ok, after rereading your first post, leave the hdd out, have the fixed optical drive in, and try to boot to the Windows cd Dell sent, it is bootable. Or a bootable floppy. It sounds like the hdd died, but not the controller on the motherboard.
I think there is a BIG problem with the Dell 8100 and 8200 laptops and I'd bet with their later series. I've owned about 3 of each model number. I have an 8500 now and see the same things happening. Here's what I see,
After about 9 months of use there are black marks where different parts of metal touch each other. For example, if you pop off the memory covers on the bottom and inspect the fingers and where they touch, you will start seeing black marks. I just received an 8200 to repair with the same problem that you have and popped off the keyboard and sure enough where the keyboard touches the chassis and the hard drive cage there was a ton of black where the parts touch each other. I suspected that this was from electricity or static charge arcing across the contacts. I then cleaned the parts with an oxide remover (that's what arcing causes) and found SEVERE pitting that reinforced my convictions that there is electricity passing through the chassis somehow.
This has happened on 4 laptops out of 6 that I've had on the 8x00 series. I borrowed my friends HD and sure enough, it booted right up after replacing the HD.
I find this to be a HUGE design flaw and I've started seeing evidence of this on my 8500 now after about 10 months. I'm not sure if this is a material or surface treatment issue but it's shocking to see material being removed where the parts touch.
I suspect there is a floating grounding problem which is somehow passing voltages to other components and eventually causes the HD to fail but I'm not really sure. All I know is that there IS some problem.
just examine your chassis and report with what you see in the sense of black marks. Let's get some data to examine!!! Take out the KB and see if there are any black marks underneath or near the HD frame
johnallg
2 Intern
•
7280 Posts
455
0
Posted July 13th, 2004 00:00