UNSOLVED

EyeHaveAQuestio

updated

21 years ago

0

7083

March 13th, 2006 15:00

XPS 400 - can I have 3 SATA's (1- normal boot, 2-RAID'd)?

Helping a friend setup an XPS 400 and was wonderring if it could be setup for booting from a single SATA drive and have another 2 drives RAID'd together?  Seems like it would be possible but wanted some info before I start ...
 
Danny
  • dougery

    2 Intern

    •

    89 Posts

    562

    0

    Posted March 13th, 2006 17:00

    I just did that with my XPS 600 and works great.  But for the 400 you'll either need to use a 5.25 bay to hold the third drive or get an external enclosure (The Athena is really nice).  I went with RAID-0.
     
    You'll need to F2 to setup and and turn on RAID for the two drives then hit controll-N to go into Nividia Media Shield to set up the drives.
     
    Then you'll need to go into Windows control panel/admininstative  tools/computer managment/disk management and format the drive(s). 
     
    The users guide has all of the instructions for this. 
     
    Hope this helps. 
     
  • suberr

    14 Posts

    562

    0

    Posted March 13th, 2006 23:00

    I have a question about this too re: my XPS 400.  I have one master SATA, and my old sata which I'd like to slave in order to retrieve the data; do I need to turn on RAID in the Bios?  Do I set it to RAID 0?
  • jimconway

    32 Posts

    562

    0

    Posted March 13th, 2006 23:00

    I want to take this one step further . . .

    I've got a small (80GB) 10,000 rpm drive as my boot drive, and I want two drives set up with RAID 0 as my main documents/video/music storage drives, and then a fourth drive to do nightly automated backups of the RAID drives.  I've already read that I'll have to find a spot for the fourth drive (I'm going to get a 5.25" inch bay adapter/cooler thing. 

    But other than that, will it work?  How do  I do it?   My brand new XPS 600 with Windows XP MCE is scheduled to be delivered tomorrow.

    Thanks for any advice.

  • dougery

    2 Intern

    •

    89 Posts

    562

    0

    Posted March 14th, 2006 00:00

    Sub,

    It sounds like you're not configuring for RAID?  You just want a master and a slave drive (one drive for extra storage)?  If this is the case, you do not want to use a RAID configuration. 

  • suberr

    14 Posts

    562

    0

    Posted March 14th, 2006 01:00

    Right, thanks dougery.  I guess I was getting confused.
     
    I want Master/slave SATA, but I'm currently running in Combi mode.  When I switch to ACHI, or any other mode in the BIOS, it locks up and goes into the endless repeat cycle on startup.  I thought it would be straightforward, plug one sata into sata 0, and another into sata 1, but I haven't been able to get it to recognize my second drive?!
     
     
  • dougery

    2 Intern

    •

    89 Posts

    563

    0

    Posted March 14th, 2006 01:00

    Jim,

    I actually did the same thing.  I used a 160gb Seagate as my boot drive, two 74gb Raptors (RAID 0) for games, and a fourth 300gb drive in an external enclosure (Athena) for backup and misc media (not USB but SATA so I can track the temp). 

    The best thing to do is read the users guide on setting up your RAID configuration.  It should work really well, it did for me.  With 4 drives though I would highly recommend increasing your ventilation in the case or set up one of the drives externally due to high temperatures (see CTskydivers thread:

     http://forums.us.dell.com/supportforums/board/message?board.id=xps_desk_hddr&message.id=887&view=by_date_ascending&page=1 )

    Even with three drives in the case I'm going to increase ventilation.  My Raptor drive temps are hitting about 44c under the shroud in a cold room.  I tried removing the shroud and my temps actually spiked even higher.  I'm planning on moving one drive to the 5.25 bay with increased ventilation leaving two drives under the shroud.  Be sure to install freeware speedfan program as well so you can monitor the temps under the hood. 

    I hope this helps, Your going to love it! 

     

     

     

     

     

  • suberr

    14 Posts

    563

    0

    Posted March 14th, 2006 03:00

    Oops, SATAs are both masters, since slave/master term is only for old PATA drives.

    I wonder why the bios isn't recognizing the other sata drive.  I leave it in combi mode in the bios right?

  • dougery

    2 Intern

    •

    89 Posts

    563

    0

    Posted March 14th, 2006 03:00

    First, check your cables and make sure everything is secure (this one got me once) :smileywink:

    Try going into Windows control panel/admininstative tools/computer managment/disk management.  Is your drive visible there?  If so, format the drive. 

    My next recommendation would be to contact support :smileysad: Hope this helps a little.  

     

    Message Edited by dougery on 03-13-2006 11:52 PM

  • jimconway

    32 Posts

    563

    0

    Posted March 14th, 2006 05:00

    Thanks, dougery, it helps a lot!  I am very excited about getting this new machine . . . .  I will read the User's Guide (I assume you mean the book that comes with the computer), although I might just look for a PDF version on Dell.com tonight . . . . 
     
    I did read another thread about heat (I think it was the same one you linked to, although I'm responding here before reading the linked thread), and I was planning to get a thing that I found on Newegg that has a heat dissipator and also helps the 3.5" drive fit in one of the 5.25" bays.  I hope that will do it.
     
    Two more questions, though:
     
    I've heard that the Raptors naturally run a little hotter than regular drives; is that your understanding? 
     
    I wasn't sure what you meant when you said that you're using SATA instead of USB to "track the temperature;" how does it track the temp?
     
    I will check out speedfan, too.
     
    Thanks,
    Jim
  • deesmygal

    274 Posts

    419

    0

    Posted March 14th, 2006 12:00

    I'm new to some of this information.

    So here I go. Why would you have a RAID 0 on anything other than your C drive?
    Don't your programs/applications need to register and install data on the C drive
    and the rest of the informatioin can be on the array but that defeats the reason
    for having the array in the first place. Which is the speed bump when playing games.

    If you are backing up data shouldn't it be a RAID 1 which makes the other back up
    disk a mute point because RAID 1 is a back up in case of a drive failure.

    I'm just asking. Can someone clear me up, please.