UNSOLVED

Christos Vlacho

updated

13 years ago

0

108521

December 22nd, 2013 19:00

T3610 - no detection of 2nd HDD after RAID 1 removal

I recently purchased the new Precision T3610 with two 500GB HDDs.
The disks were configured to operate in RAID 1 configuration.

As I do not need the RAID configuration I removed it by accessing the Intel RAID utility (Ctrl+I) and setting both disks to Non-RAID.
After that, both disks are properly identified in both BIOS and Device Manager of Windows 7.
But the 2nd HDD cannot be seen on My Computer. I need to format it in order to use it as simple storage drive.
 
Maybe should I just turn off the RAID and just use the AHCI option in the SATA Operation tab ? (windows reinstallation is mandatory after that ?)
 
I need also to replace the 1st (bootable) drive with an SSD. Will there be any problems with that ?
  • osprey4

    6 Operator

    •

    34230 Posts

    2384

    0

    Posted December 24th, 2013 02:00

    Hi Christos,

    As long as you are going to install an SSD anyway, I would set the controller mode to AHCI, perform a fresh installation of the operating system onto the SSD, then set up the HDDs the way you want to.

  • theflash1932

    11 Legend

    •

    16255 Posts

    2384

    0

    Posted December 26th, 2013 13:00

    Agreed ... you don't want to clone your installation to an SSD ... do a clean install. 

    There will be no difference between using the drives as non-RAID in RAID mode and in AHCI (non-RAID).  If you are doing a clean install anyway, switch to AHCI, if not, then you can leave it as it is. 

    Drives will not show up in My Computer until they have been initialized/formatted.  You do this in Disk Management (right-click [My] Computer, Manage).

  • 2384

    0

    Posted April 12th, 2014 11:00

    I have a similar problem with T3610.

    Rain on. Legacy boot.

    SATA0 - 256GB SSD

    SATA2 and SATA3 HDD 1TB, configured as RAID 1

    When I boot with Win7 installation DVD, it starts pre-load from DVD . Than it seems language setting step. I select language and clisk Install. Installation go stop. Windows says No CD-DVD drive. I click to Browse, I am seeing onlt removable drives. No HDD, no Optical. 

    I updated Bios. Doesn't changed. 

    If I install with AHCI mod everything OK.

    So T3610 - RAID 1 doen't work. I couldn't install windows with RAID 1

  • theflash1932

    11 Legend

    •

    16255 Posts

    2384

    0

    Posted April 12th, 2014 15:00

  • 2384

    0

    Posted April 13th, 2014 03:00

    Thank you THEFLASH1932. My problem was installation windows 7 on SSD. If I configure SATA operation as RAID, in first step of installation get error: Required CD/DVD drivers not found.

    I research on internet and I found the problem, RAID mode require some driver like you said. I downloaded the dirvers and copied a USB flash disk. Tomorrow I will install with using this USB.

    Best Regards

  • Charlenze

    1 Message

    2384

    1

    Posted April 28th, 2014 02:00

    Hi Alogonullu,

    If you couldnt solve the problem, download this file:

    http://www.dell.com/support/drivers/us/en/04/DriverDetails/Product/precision-t3610-workstation?driverId=HXT48&osCode=W764&fileId=3341038105&languageCode=en&categoryId=SG

    And if you do in on another computer it will say "computer not compatible", dont mind about that and go to C:\Dell\Drivers\HXT48\Drivers\win7\AHCI and copy the folder x32 or x64 (depending on the type of processor you have) to an USB drive. Then you can choose the folder while trying to install Win7 in order to load the drivers for the SSD.

    I would recommend that you change the SATA mode to AHCI.

  • Chemware

    13 Posts

    2384

    0

    Posted August 17th, 2014 19:00

    Same problem as Alogonullu with my T3610.


    Originally configured with a 500 GB HDD, I purchased a 240 GB Silicon Power S55 SSD to install as a boot drive.


    I disconnected the HDD, plugged in the SSD, went into the BIOS and set SATA Operation to AHCI, and booted the Windows 7 Pro installer from a known good USB installation drive. I got the:

    "Load Driver

    A required CD/DVD drive device driver is missing. If you have ..."

    I figured that it wanted some of the Dell Intel chipset drivers, and tried various ones in vain. After some help from Prof Google, I found this thread and tried the Storage-Controller_Driver_HXT48_WN_3.8.0.1111_A04, expanded onto another USB drive, from the location above. This at least led to a:

    "Select the driver to be installed"

    with an actual entry: "Intel(R) C600 series chipset SATA AHCI Controller ...".

    Selecting that and clicking on Next then led to a lot of green progress barring, but after 20 s or so:

    "No new devices could be found. Make sure the driver files are correct and located on the driver installation media."

    All I could do from here was to cancel installation.

    This made me think that the SSD was faulty, so I attached it as a secondary driver to another PC, formatted it, tossed about 1 GB of files onto it, and it worked perfectly.

    I then changed the SATA Operation to ATA in the BIOS, and tried installation again. Another "Load Driver" dialog, but this time it found nothing in the Storage-Controller_Driver_HXT48_WN_3.8.0.1111_A04 file. Instead, after some searching, it found drivers from the Chipset_Driver_RKDH5_WN_9.3.2.1010_A01 file, with driver descriptions of:

    "Intel(R) C600/X79 series chipset 2-port SATA IDE controller - 1D08"

    "Intel(R) C600/X79 series chipset 4-port SATA IDE controller - 1D00"

    but none of them worked.

    At this stage I cannot install Windows to this SSD.

    Any ideas ???


    Should I find a new SSD or a new workstation ?

  • theflash1932

    11 Legend

    •

    16255 Posts

    2384

    0

    Posted August 17th, 2014 20:00

    The CD/DVD driver message 99% of the time means that your Windows media is corrupt. 

    Try:

    • Downloading the ISO again
    • Downloading the ISO using a download manager
    • Check file hash for download
    • Try a different media version/refresh (where are you getting the ISO?)
    • Create USB again with new ISO
    • Use a different USB drive
    • Do not use the USB 3.0 ports
  • Chemware

    13 Posts

    2384

    0

    Posted August 17th, 2014 22:00

    ps: I visited the Intel and downloaded the STOR_Win7_8_12.5.0.1066_f6flpy-x64.zip AHCI drivers.


    They worked just like the Dell Storage-Controller_Driver_HXT48_WN_3.8.0.1111_A04 drivers - that is to say, they failed at the last step.

  • Chemware

    13 Posts

    376

    0

    Posted August 19th, 2014 19:00

    I tried all of the above, and it was only the combination of a new ISO on a new disk in a USB2 port that worked.

    Thank you !