UNSOLVED

shibumi2k

updated

20 years ago

S

shibumi2k

7 Posts

0

43262

February 8th, 2007 17:00

Removing RAID on XPS 410

Hi Folks,

I'm sure it's been asked before, but in searching through the forums I didn't find the answer... I've seen several folks ask about going from RAID 1 to RAID 0 and vice-versa, but I want to remove RAID completely, and just have a C: and a D: drive (or more if I partition them up further).

I just ordered an XPS 410 off of the Outlet and it is coming w/ two 250 GB HDs in a RAID 1:

250 GB EIDE SATA II Hard Drive (7200 RPM)
250 GB EIDE SATA Hard Drive (7200 RPM)

1 UD305 Module,Hard Drive,250GB,S2, #1,ULD,WD-HAWK $0.01
1 UD306 Module,Hard Drive,250GB,S2, #2,ULD,WD-HAWK $0.01

1 F6407 Module,Information,RAID 1, Dimension

Through my searching on the forum I've learned the difference of the RAID 0 and RAID 1, and while I'd like the performance increase that a RAID 0 offers, I don't like the risk of total data loss. I also like to have one drive for my OS and the second physical drive for all of my data storage (primarily for video edits, photos, music).

Also, with the new system I was hoping to dual boot with 1 partition being XP Pro (which is coming loaded on the 410), and then a second partition being some form of Vista (either my express upgrade to Business - or if I decide to splurge - Ultimate).

I'm not really interested in RAID 1 because I already have a network drive (500 GB Buffalo Linkstation) and I don't like the thought I "losing" 250 GB of drive just to mirror the other drive.

So - the questions:

When the system shows up, can I safely / easily remove or "turn off" RAID 1 and just go the old school way of having two completely separate HDs - a C: and a D:?

If so, how?

Will I lose the data (OS) on the C: drive by removing RAID 1?

Will I just be able to reformat D: after removing RAID 1 and start clean w/ that drive?

I'm assuming I may have to reinstall the OS, but I was thinking I may (or should) have to do that if I wanted to do the whole dual boot thing anyway - create 2 partitions on C: - one for each OS. If I do, repartition and install from scratch, any special things I should be aware of when doing this on a Dell? Special drivers etc? Or will it all be on the Drivers CD (at least enough to get me up till I can update to the latest drivers off the net).

Finally - can I even setup for a dual boot w/ one of these Vista express upgrades?? I've *heard* that w/ Vista (unlike previous MS releases) that just having the XP CD won't be enough when you're doing an upgrade - that you'll have to actually have XP installed on the partition that you want to put the Vista upgrade on...

If that's true, would I have to repartition my C: - then install XP in both of the new partitions - and then install the Vista Upgrade in my second partition?

Thanks - sorry for the long post, wanted to have all of the info in here - hope I didn't leave anything out! Thanks again!
  • TomXPS

    1310 Posts

    750

    0

    Posted February 8th, 2007 17:00

    On Power up you should see a screen where it says you can press CTL I to get in to the RAID setup.   From here you can break the RAID 1 Array.
     
    Assuming it RAID 1, you get a warning about loosing the Array Data which is true but after the break up you should see two drives with identical data on both of them.   I broke the Array on My XPS Gen 2 with no problems.   
     
     
  • njr999

    83 Posts

    750

    0

    Posted February 8th, 2007 18:00

    You can break the RAID and then go into the BIOS and change the SATA operation from RAID On to RAID Autodetect/ATA. Your hard drives will then be non-RAID. When I did this I had to then do a repair install of WinXP which is quite simple as long as you have a WinXP CD.
     
     
  • shibumi2k

    7 Posts

    750

    0

    Posted February 8th, 2007 19:00

    Great news!!

    So ctrl+L to go into RAID settings and break the array, then go into the bios and set it to Autodetect. - Thanks for the help!

    H7658 Module,Software,Windows XP Pro Service Pack 2,CD,English DAO/BCC

    is listed on the order, so I'm hoping that means they're shipping an actual CD for XP - looks that way.
  • dcgtls

    2 Intern

    •

    940 Posts

    750

    0

    Posted February 9th, 2007 02:00

    Here you go, I posted this not to long ago. LINK  Once you have broken the raid array follow these directions and you will be set.
    Dave
  • shibumi2k

    7 Posts

    750

    0

    Posted February 9th, 2007 13:00

    More good info! Thanks Dave!

    BTW - do you (or anyone) have a software recommendation for repartitioning a drive these days? I'm planning on setting up a dual boot (XP and Vista) on my C: drive after I turn RAID 1 off.

    I haven't played around with partitioning for years - and back then I used Partition Magic. Is that still the way to go? Anything better out there these days?

    Message Edited by shibumi2k on 02-09-2007 09:05 AM
  • dcgtls

    2 Intern

    •

    940 Posts

    750

    0

    Posted February 9th, 2007 19:00

    I use Partition Magic 8.0. Acronis has a good program for this also.
  • JoannieMc

    2 Posts

    750

    0

    Posted February 10th, 2007 10:00

    Morning: I'm in the same boat as the original poster - XPS 410 with 2 hard drives in RAID 1 array. Don't really need RAID, just want 2 drives - 1 for OS and 1 for data. So, being naturally cautious I'd like to confirm my understanding of the process to remove RAID, please.
     
    Sounds like I can break the array and NOT have to reinstall WinXP MCE?? Do I do this by:
     
    1.copying and executing the mergeide.reg file and copy drivers (if needed),
    2. then break the array by Ctl l on power up,
    3. then go into BIOS and change the SATA operation from RAID on to RAID Autodetect/ATA?
     
    Thanks!
     
    P.S. The PC has Intel Matrix Storage Console loaded. Does that make a difference??
     
  • 750

    0

    Posted February 10th, 2007 21:00

    When I initially received my 410 I only had 1 hd and the raid setting in the bios was on.  I to have the matrix storage console.  It's my opinion that you only need to do the ctl I and break the array then go in to the disk manager and format the storage drive.
  • TomXPS

    1310 Posts

    750

    0

    Posted February 11th, 2007 22:00

    The RAID array of 2 disk would show up as one in the Disk Manager.  Once you break the Array you have 2 disk exactly the same, with RAID 1.   After the braking you can format the other drive etc.
     
    As far as the BIOS setting you can set it to Non RAID or leave it alone.   Do not think it makes much difference but on my machines I always worked as RAID 1 except for a few times I broke it to re-install the OS.   Sort of like breaking it before I install then I always have a old image to go back too until I re-establish the Array.
     
    Anyway with me the RAID 1 has saved me once from loosing everything so I am a very big fan of it.   To me the price for drives is so cheap now of days that I like the extra protection.   Been running RAID 1 on a XPS gen2 for over 3 years.    My XPS 410 is not setup yet, but will be doing it soon.
     
     
  • JoannieMc

    2 Posts

    586

    0

    Posted February 12th, 2007 11:00

    Well, I have to confess it was much easier than I thought. I agonized over the 'right' way to disable RAID 1 on my new XPS-410 with 2 SATA 250GB HDs. Since Dell included Norton Ghost, and I have an external HD, RAID 1 seemed like overkill, not to mention wasted disk space. If I have an HD failure I'll have to work a bit harder to recover, but I'm OK with that.
     
    All I did was ctl I at boot up into Intel Matrix Storage Manager, select option 3 to 'Reset Disks to Non-RAID'. Then reset each disk. The Intel Matrix Storage Manager Manual even states that resetting members of a RAID 1 array will NOT delete data. Not same story with RAID 0. I made no changes to BIOS setup...it's still set to RAID ON. Advice was given to change BIOS to Autodetect, but I'm not sure what that buys. Any thoughts from others??
     
    So now I have 2 independent drives, both have a secondary partition for Norton (I guess that makes 4 logical drives). WinXP MCE is running on the C drive primary partition. I reformatted the 2nd drive primary partition to delete all the Win files, then moved 'My Documents' over. I left the Norton partition on the 2nd drive. I reconfigured Norton to copy the recovery points of the 1st drive to the 2nd drive Norton partition and vice versa. That way if I lose a drive I can recover the image....I think. I understand there are some issues with Norton Ghost...I'll have to follow up on them. I tested with the 2nd drive and easily recovered its primary partition. Not brave enough to test with the C drive yet. 
     
    Anyway, thanks to all who provided great answers!