My system is a Dimension 4550 with a Dell installed Samsung 616-T DVD ROM, running Windows XP SP 2 Home Ed.
When the DVD player failed to play some DVD's at all and others inconsistently I downloaded the A03 firmware update and attemted to install it. The update hung at the command prompt "Secondary Master:" on several attempts. At about the same time I had successfully flashed my BIOS from A02 to A08.
Since then the boot sequence stops with the message that Secondary Drive 0 and 1 were not found. Both are set to AUTO in setup and list "unknown device" to the right, even though 1 is the CD-ROM drive, which is functional. The DVD does not appear in Device Manager, but the CD-ROM does.
I have uninstalled and reinstalled the Secondary IDE controller and CD-ROM hoping the DVD would be detected on Scan, but this did not work. Both 0 and 1 are set to DMA if applicable, though the actual transfer field reads Not Applicable for 0 and PIO for 1.
I tried to revert to BIOS A02 by clearing NVRAM with no success. I checked the power cables and connections for both drives and they appear secure.
Is this a software or BIOS issue, or do I just have a dead DVD ROM?
My money would be on the dead DVD-ROM. Open the case and disconnect the good CD-ROM, I truly wish Dell would recommend disconnecting any second drive on the same IDE cable when flashing a drive, we have seen more problems associated this way. If the drive is under warranty, download the firmware once more, if DOS base, use a new or freshly formatted floppy with no bad sectors, try the flash again. If it fails, contact Dell bye, explain the Dell-Firmware failed and the drive now does not work. Dell should replace the drive.
If out of warranty, jump over to the Dangerous Brothers Web site and search for a "hacked" firmware, also the MTK Flash Utility, both have been known to revive a bad flash at times...or...spend $30 for a new drive and not go through the hassle.
Happy Holidays!
God, grant me the senility to forget the people I never liked anyway, the good fortune to run into the ones I do and the eyesight to tell the difference. CD/RW Link
Dear Demd: I would follow Predator’s advice. He has forgotten more about CD/DVD problems than most of us will ever learn. But I had a problem very similar to yours and posted “my solution” on this forum a few weeks ago. [It contained a couple of nonfatal errors (such as referring to Secondary drive 1 as a “slave” to Secondary drive 0 rather than recognizing that the Samsung drive is set to Cable Select - which shows what a neophyte I am - but at least the procedure worked for me in restoring the Samsung 616-T drive to its original functional state]. You may want to check it out at: http://forums.us.dell.com/supportforums/board/message?board.id=dim_cdrom&message.id=89452#M89452. Good luck
I appreciate the kind words. I would like to add your post to the CD/RW site for a good reference in using the MTK Flash Utility, I always list the name of the Member providing the information, let me know if this OK with you.
Happy Holidays!
God, grant me the senility to forget the people I never liked anyway, the good fortune to run into the ones I do and the eyesight to tell the difference. CD/RW Link
Thanks both to Predator and David from Texas. I opted to replace the drive and it is now fully functional. I had already spent frustratiing hours on this. I can really appreciate the hours you spent David, and taking the time to post your solution will surely benefit many who will be victims of this flawed firmware update.
Well my friend, glad you got a working drive again. If you get a rainy day and time to kill, give David`s suggestion a try, you may end up with a spare drive. If you do this, pleea...zeee disconnect both existing drives and run the flash with the Samsung as the only drive on the Secondary Channel, better safe than sorry...
Happy Holidays!
God, grant me the senility to forget the people I never liked anyway, the good fortune to run into the ones I do and the eyesight to tell the difference. CD/RW Link
Sure Predator, I'd be greatly honored if you did that. Your site is a treasure trove of information that has helped countless thousands of frustrated CD/DVD users in distress. Please clean up my posting any way you see fit (such as correcting silly errors and leaving out non-informative "fluff"). If my experience helps resuscitate one crashed DVD ROM drive, then my posting will not have been in vain. Glad to see that Demd is now back in business.
God, grant me the senility to forget the people I neverliked anyway, the good fortune to run into the ones I do and the eyesight to tell the difference. CD/RW Link
i went back and read your instructions from your prior 12/5 post... I'm wondering if you can shed some light on my similar (but possibly not the same) problem. I just installed a new dvd rw (sony) drive. I disconnected the original cable and instead, installed the new one, disconnecting and reconnecting along the way, the existing cd-rom drive.
Now...... nothing works. After I was able to navigate through the initial boot ( i get the error message that says "secondary drive 0 not found, secondary drive 1 not found press f-1 to boot or f-2 to run utility setup") the computer did give me pop ups from my tool bar telling me it located new hardware.
This process froze ....... I wasn't able to complete anything or do anything and had to reboot and go through the round about boot process again because of the error message.
Now, my CD or DVD drives are not even listed on device manager.
Is there a simple solution for this? Will returning to ensure proper connection along the cable help me to fix this? (i hope)
Dear H20Girl: This sounds like a cable connection or software problem. It is best addressed by one of the forum "masters" such as Predator (whom I have already alerted) or Skybird. I would recommend that you describe your problem again as a new posting. Often problems that are discussed as part of an old thread get lost or ignored. Don't despair, help is near.
Predator
2 Intern
•
15286 Posts
1478
0
Posted December 28th, 2004 10:00
Hi Demd,
My money would be on the dead DVD-ROM.
Open the case and disconnect the good CD-ROM, I truly wish Dell would recommend disconnecting any second drive on the same IDE cable when flashing a drive, we have seen more problems associated this way. If the drive is under warranty, download the firmware once more, if DOS base, use a new or freshly formatted floppy with no bad sectors, try the flash again. If it fails, contact Dell bye, explain the Dell-Firmware failed and the drive now does not work. Dell should replace the drive.
If out of warranty, jump over to the Dangerous Brothers Web site and search for a "hacked" firmware, also the MTK Flash Utility, both have been known to revive a bad flash at times...or...spend $30 for a new drive and not go through the hassle.
Happy Holidays!
God, grant me the senility to forget the people I never liked anyway,
the good fortune to run into the ones I do and the eyesight to tell the
difference.
CD/RW Link