AIO 926 Inkjet driver incompatible with Windows 10. When will it be updated and
tested?
AIO 926: Even after manual install, Windows 10 says that the printer driver is unavailable [not recognized]. Can scan but not print. I have returned to Windows 7 and want to know if Dell intends to update and test the drivers for Windows 10 and when. The properties menu does not give compatibility options for printer drivers.
I have spent hours trying to fix this and even paid for an online tech service which finally found that Dell admits Windows 10 is incompatible with AIO 946, my printer. I called and they urged me not to switch back to Windows 7 because they have to find a solution soon. I think they are trying to get us to buy new printers and think they should have warned us before the upgrade.
Thank you so much PudgyOne! I followed your directions VERY CAREFULLY and finally I got our Dell AIO 926 to work with our Windows 10 laptop!
FYI, on the referred page with patch and driver files, the link for "patch" SAYS it leads to R166248 (cleanup utility) but the page that comes up doesn't have that driver anymore, so I found it by Googling.
Also on that page, I clicked the link for "64-bit drivers", and on that page selected Vista 64-bit, and downloaded that driver to my desktop (R150575). Now -- it was a compressed file that, when opened, the self-extractor is set to automatically run Setup.exe after extraction... so once it was done extracting, I had to Cancel out of the Setup.exe, then go to the location where it was extracted, and THERE I could right-click it to go to Properties and set it for Vista SP2 Compatibility, then right-click again and Run as Administrator.
Lastly, I also had to go to Control Panel > Devices & Printers > right-click the Dell 926, go to Printer Properties "Advanced" tab where the default setting for the print processor was "LEMF", and change it to "NT EMF 1.008".
FYI Administrators -- THIS should be marked as the SOLUTION!
Download the Vista 32-bit drivers for Windows 7, 8, 8.1 and 10 32-bit or the Vista 64-bit drivers for Windows 7, 8, 8.1 and 10 64-bit. Install the Vista drivers in the Vista Compatibility mode You'll get a message, the printer is not connected. Connect the printer at this time(powered on).
Download the Vista 32-bit drivers for Windows 7, 8, 8.1 and 10 32-bit or the Vista 64-bit drivers for Windows 7, 8, 8.1 and 10 64-bit. Install the Vista drivers in the Vista Compatibility mode You'll get a message, the printer is not connected. Connect the printer at this time(powered on).
After upgrading to Windows 10 from Windows 7 my 926 Photo All-in-One Printer stopped functioning properly (I would get a connection error when I tried to print a document). Following your instructions resolved the issue.
Hi Rick, have a question about those steps to allow a 926 inkjet to work with windows 10. I went through all the steps and am stuck on the "Install the Vista drivers in the Vista Compatibility mode You'll get a message, the printer is not connected." I am not sure how to enable this compatibility mode in windows 10. I tried downloading the driver first, right clicking it in the file browser, left clicking properties and going to compatibility - but compatibility was not an option.
From what I understand, I need to actually install the Vistra drivers in the vista compatibility mode to get this to work. I have no idea how to achieve this step. Could you help me out?
Right click on R150575.exe, then left click properties. You'll see the image below, then click on compatibility.
Click where I have the arrows, then click apply, then ok. Make sure the printer is not connected with the usb cable. Then right click on the file, left click run as administrator.
I am experiencing the same problem and followed all of your steps listed above. Once the file opens, I'm not sure what to do. I tried the "setup" but received the error message that my new Dell printer is not compatible with Windows 10. Any advice? I am really frustrated with Dell not having a driver for Windows 10.
Looking like it doesn't work with Windows 10 Threshold 2? Setup starts and ten seconds later closes with no notifications. .NET and Java7u80 are installed, compatibility/admin was used. I also tried to default IE, enable Java in IE and the Setup.exe files in both locations (one is in C:\dell\drivers\R153976\Fax\install\x86). Any suggestions? Thanks in advance.
Update: Had an old copy of R146832 and that one opens setup.exe. The install froze, the printer was already installed and I ended the process. It prints!
ejerry
1 Message
13378
1
Posted August 13th, 2015 20:00
I have spent hours trying to fix this and even paid for an online tech service which finally found that Dell admits Windows 10 is incompatible with AIO 946, my printer. I called and they urged me not to switch back to Windows 7 because they have to find a solution soon. I think they are trying to get us to buy new printers and think they should have warned us before the upgrade.