bigfoot53

updated

12 years ago

B

bigfoot53

1 Rookie

•

5 Posts

0

187536

September 12th, 2014 09:00

Upgrade from PERC 6 I/R to H700

Hello Everyone,

I have a T610 with the integrated PERC 6 I/R controller and want to upgrade to a H700 so I can add a second raid 5 array.  Is it possible to migrate the existing raid 1 array to the new H700 Controller? and then configure the new raid 5 array?

Thanks

Bruce

  • DELL-Chris H

    7 Practitioner

    •

    9682 Posts

    •

    48046 Points

    11929

    0

    Posted September 12th, 2014 11:00

    Bigfoot53,

    You can migrate the array from the Perc 6/i to the H700, as seen on page 9 of this link - http://www.dell.com/downloads/global/products/pvaul/en/perc-technical-guidebook.pdf

    What you would actually need to do is first get a good backup of the data, as you should always do when working with the array. After that you will install the H700 and then boot to the controller BIOS (CTRL-R at prompt) From there you will highlight the controller and hit F2. From the F2 menu you will select Foreign Config. In the Foreign Config menu you will select IMPORT FOREIGN CONFIGURATION. What that will do is tell the controller that the raid configuration information on the Disks is what should be used. It should then import the configuration to the H700. Ensure all the drives are migrated.

    Let me know how it goes.

    DELL-Chris H

    Social Media and Communities Professional

    Dell Technologies | Enterprise Support Services

    #IWork4Dell

    Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!

  • theflash1932

    11 Legend

    •

    16255 Posts

    11913

    0

    Posted September 12th, 2014 17:00

    I have a T610 with the integrated PERC 6 I/R controller and want to upgrade to a H700 so I can add a second raid 5 array.  

    Chris gave some sound advice, but let me come back to the "reason" for the upgrade:  The PERC 6/i, like the H700, will easily support a second VD (RAID 5, whatever), so that would not be a valid reason (alone) for the upgrade. 

    Or did you mean the SAS 6/iR?  The SAS 6/iR, while it also will support 2 VD's, it does not support RAID 5, and direct migration of disks/VD's from a SAS 6 is not supported on the H700.  You would need to first install the H700 in the system to load the drivers in Windows for it, then power off and attach disks to it.  Success rate varies, so be prepared with a backup.  You could also use a backup/restore using software capable of restoring to different hardware - able to load the appropriate drivers

  • bigfoot53

    1 Rookie

    •

    5 Posts

    11913

    0

    Posted September 16th, 2014 06:00

    Thanks  all,

    The system is up and running with the new H700 card and have setup and configured the new Raid 5 array.

    I had a little issues with the Import of the foreign config but with a little tweaking it worked.

    Thanks again for all the help.

    Bruce  

  • avi123

    1 Message

    11913

    0

    Posted December 17th, 2015 08:00

    Hi,

    could you help me with the cables you have used to connect the H700.

    the cables for the 6i do not fit the H700. 

    Do you have a list of needed parts to upgrade from the 6i to the H700?

  • Molon Labe

    14 Posts

    11324

    0

    Posted June 23rd, 2018 22:00

    On an R610, when I simply swapped out the PERC/6i for the H700, the H700 picked up the VDs automatically, but it wouldn't boot.

    Apparently because the boot OS did not have H700 drivers.

    So I replaced the PERC/6i, rebooted, recovered the VDs (not easy, had to reconfigure VDs without initializing).

    Shutdown, inserted the H700 in a PCIx8 slot, rebooted.

    The OS (Windows Server 2016 Standard) recognized and installed drivers for the H700.

    Shutdown. Replace PERC/6i with H700. Reboot. CTRL-R but H700 picks up VDs automatically.

    Continue...boots fine.

    PS: H700 cables for an R710 will not work with an R610. The A controller cable is too short. But you can easily find correct cables for R610 on eBay.

  • Molon Labe

    14 Posts

    11319

    0

    Posted June 23rd, 2018 22:00

    Dell Part Number for H700 cables that work with R610 (or R710) server is 0M246M.