I just noticed one of the picture you have screenshot has your server service tag. It is considered your private info on a public space. I would suggest removing it to safe keep your informations.
DELL-Joey C
Social Media and Communities Professional
Dell Technologies | Enterprise Support Services
#IWork4Dell
Did I answer your query? Please click on ‘Mark as Accepted Answer’ if I did.
Hi, if other DIMMs that you are sure are working do not work in A1 and B1 slots. Then the slot is suspected first. The possibility of it being from the processor channels is considered later. When compatible parts are used, the probability of a processor-related problem is less likely. The DIMM itself or the slot on the motherboard is more likely to be suspected. Also, as far as I understand, you have installed parts on the server a few times. There may have been static electricity on the server, so I recommend draining the flea power.
1. Power the server down. 2. Disconnect server from all power cables, Network cables. 3. Hold down the power button continuously for at least 10 seconds. 4. Insert power cabless and network cables back to the system. 5. Wait about 2 minutes before powering on the server for iDRAC to be refreshed. 6. Power the system on.
DELL-Erman O
Social Media and Communities Professional
Dell Technologies | Enterprise Support Services
#IWork4Dell
Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!
I have the same problem with my Dell G3 3500; the second dimm slot is not visible. I tested both of the 4GB RAM modules in the first slot and they worked fine. I remember it crashed with a blue screen on Windows 10 earlier, but I'm not sure how many times. I've been having issues with my Dell G3 laptop since the bios was updated automatically to the current version. Dell better fix or replace my laptop for free. When I first received this laptop, the package arrived damaged, and I spoke with the higher-up, who said that if I ever had a problem with it, I should contact him. I wished I still had his email and an extension to his department.
I have much more interesting case. Sam error (regarding A1 and A2) is on 5!!! units of T440 and recently we got same on 1x R440. We tried everything - change CPU, change RAM, update, repurpose, reset and hard reset iDrac, power drain... And still have no soluton for it.
You may first try a flea power drain and Clear NVRAM:
drain flea power (shut down, disconnect power cables and Network cables, hold in power button 20 seconds with cords removed).
After flea power drain, system has to set for 3 minutes for DRAC to reset without any power plugged in.
Then plug in NIC and power but wait 2 minutes before power on to give DRAC time to initialize.
Check result
.
Clear NVRAM - there is a map under the lid to show the jumper location. Shut down, Set jumper to the Clear position, power on and Post up to the jumper error, shut down and return jumper to original location.
Check result
Next I would recommend bring them down to minimum to post configuration.
Check for any bent pins in CPU and DIMM sockets.
Test each DIMM one at a time with CPU1 and A1 socket then build out the memory incrementally.
T440 minimum to post:
The components mentioned below are the minimum configuration to POST. Remove anything that is not on the list.
Minimum to post leads to critical error, because no RAM found on system, if we use slots A1 or A2. And normal boot, if we use another slots.
Actually I haven't seen them working all normally. Would agree, that 1-2 units could be failed as they are not new. But from one batch all 5 units of T440?
BTW we got 2nd unit of R440 with exactly same problem.
DELL-Chris H
7 Practitioner
•
9682 Posts
•
48046 Points
0
0
Posted July 24th, 2024 14:41
DELL-Chris H
Social Media and Communities Professional
Dell Technologies | Enterprise Support Services
#IWork4Dell
Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!