I have been experiencing some slowness with my wifi card. For some reason the connectivity drops to 1Mbps and slows down. I understand that there are many different factors that can be involved due to this being rf technology. I have another laptop with a Dell Truemobile 1350 b/g being used in the same location and the connectivity never drops under 18Mbps. Currently I have Windows XP pro w/sp1 installed. All the drivers are current, as well as bios. Windows is currently controlling my connections. If anyone can give me some tips it would be very much appreciated.
I don't think changing the channels is going to do anything, I have another unit with a Dell Truemobile which is working fine never drops down under 18Mbps. I would think if there was a problem with the interference on the channel I'd probably would be seeing the same problem on the othe other unit. Something leads me to believe that theres a config/compabability issue somewhere with the Intel 2200. What I've done is disabled the wireless zero configuration service, then I installed the Intel Proset utility which is now managing the connections. I still see the drops in speed however it's not as frequent and not as slow. The connection shows a status of excellent to good however the bandwith still sinks down to 1Mbps. To further add this is not only happening in one location but in multiple locations. I have access to about four different AP's that I connect to daily and on each one I'm seeing a drop in performance. The only thing all locations have in common is the card. I've had a good deal of experience with 802.11 technology, however this is my first time with an Intel Centrino solution. The only other time I've seen this happen with an 802.11 solution is with a defective card. I may call Dell tomorrow to get this replaced being that this unit was just delivered this week. I just dread wasting my time with overseas support.
I am having the same problem with the Intel 2200 on my 8600. I have used it with 2 different Linkysy routers. In both G and B modes it shows excellent signal signal strength and drops down in steps to 1 MBPS and even sometimes totally drops my connection (like it did while typing this post) even though I am broadcasting my network SSID at the router. I think it has to do with the 1.5M chip setup controling the power consumption of the wireless device. I am not sure though. I have tried to get the wireless connection to work using the Intel Pro software and while I can connect to the router, I can't get on the internet no matter what I try. Any help would be greatly appreciated!
Just for clarification you can connect and surf while using just the built in Windows XP support however when you use Intel Pro set you are not? Do you have any encryption setup on this router, that's the only real thing I can think of as going wrong if you've connected to the same router before outside of using Intel's util. I also noticed the Intel Pro set util does not have any support for WPA.
No never went into network only the Intel Proset util. As far as the power consumption goes, by default the Intel Util sets the card to use maximum performance so I take it the radio is running at full strength. I have now enabled logging within the intel utility to see if I can see any patterns in the performance drop. I'll keep you both posted on my findings.
I am using WEP. When using Intel Pro to control the 2200, it shows me connected at 54 MBPS. But I do a tracert to 192.168.1.1 and it says I can't connect. It goes nowhere. I have to use System Restore to get connected back to the Internet again.
Yeah they are. Router is a DHCP server. I first tried to remedy this problem by upgrading to the newest Intel Pro 2200BG drivers and could never connect to the net after doing that. Had to go back to System Restore to get online. I dread calling India about this. When it goes down to 1 Mbps it does nothing. I would hate to have to end up buying a Wi-Fi card to get around this.
Message Edited by Slick1ru2 on 06-18-2004 07:34 PM
Message Edited by Slick1ru2 on 06-18-2004 07:34 PM
Message Edited by Slick1ru2 on 06-18-2004 07:34 PM
boppo
2 Intern
•
4376 Posts
363
0
Posted June 18th, 2004 02:00