UNSOLVED

carphost

updated

2 years ago

C

carphost

1 Rookie

•

2 Posts

0

14137

February 28th, 2005 13:00

Mysterious Rebooting Powerconnect 3348's

Im not sure if this has been covered here, I attempted to search for a previous message. In case you don't know, there is a problem with PowerConnect 3348 switches with both firmware version 1.1 and 1.2 where it will reboot if you type the command "show runn" then [TAB] and enter. I have found no work-around other than simply NOT doing a "show runn[TAB]". We have (3) of these switches currently and all three display the problem. We also have several 5324's and they do not show the problem.

Here is how it looks live:

sfw-sw2# sh ver
SW version 1.2.0.6 ( date 15-Nov-2004 time 14:22:46 )
Boot version 1.0.0.13 ( date 11-May-2003 time 14:58:20 )
HW version 00.00.02


sfw-sw2# sh running-config
port storm-control rate fastethernet 9000 port storm-control enable unknown fastethernet port storm-control enable broadcast fastethernet port storm-control enable multicast fastethernet no spanning-tree interface ethernet 1/e1 description 1/e1 exit interface range ethernet 1/e(1-4) speed 100 exit interface range ethernet 1/e(1-4) duplex full exit interface range ethernet 1/e(1-2) flowcontrol on exit interface ethernet 1/e2 description 1/e2 exit interface range ethernet 1/e(2-3) ...
More: , Quit: q, One line:

* and I press enter a few times then it dies *

after switch is back I get this error:

sfw-sw2# 01-Jan-2000 15:43:55 %SYSLOG-F-OSFATAL: IOTRMP_get_task: no char
***** FATAL ERROR *****
Reporting Task: IOTG.
Software Version: 1.2.0.6 (date 15-Nov-2004 time 14:22:46) 0x454ec 0x4551c 0x48140 0x2b6d7c
0x2753a8
0x3cb94
^^ this event was logged before the last reboot.

***** END OF FATAL ERROR *****

sfw-sw2# 01-Jan-2000 01:02:54 %BOX-I-GS_Change: Global status is nonCritical, last global status was ok, timeStamp 108784 01-Jan-2000 01:03:31 %INIT-I-Startup: Cold Startup
  • 612

    0

    Posted March 1st, 2005 23:00

    I duplicate this issue in my 3348 with both firmware version too. Is any new fix avaliable?
  • Asounds

    1 Rookie

    •

    16 Posts

    612

    0

    Posted March 10th, 2005 19:00

    I just installed my Powerconnect 3348 today, and several times it has rebooted for no reason. Once while I was attempting to configure, again while I was browsing through the web interface.

    The last time I received this error message in the log file:

    %SYSLOG-F-OSFATAL: EXCEPTION OCCURRED in task IDLE: PROGRAM exception ***** FATAL ERROR ***** This is exception number 1 in this board. SW Version : 1.2.0.6 Version Date: 15-Nov-2004 Version Time: 14:22:46 Stack information: ------------------ Stack bottom 0x00a71af8 Stack base 0x00a72af8 Stack size 0x00000ef0 Stack usage 0x000002e8 Instruction 0x000375d8 Accessed data 0x00000000 Stack pointer 0x00a729c8 Machine state register 0x0008b030 Condition register 0x22000020 PCI Status register 0x000

    There is also this error in the log file. Doesn't look good.

    %2SW-F-FATAL: DILC_fatal_error: ERROR return: -27 soc_gbp_size_probe - Memory test failed. ***** FATAL ERROR ***** Reporting Task: ROOT. Software Version: 1.2.0.6 (date 15-Nov-2004 time 14:22:46) 0x454ec 0x4551c 0x48140 0x2b6d7c 0x1c5434 0x1c58e8 0x1c946c 0x315f5c 0x333c9c 0x32ddd4 0x32724c 0x34dd48 0x34de80 0x353178 0x3170f4 0x2bb668 0x5e120 0x3cb94 ***** END OF FATAL ERROR *****
  • carphost

    1 Rookie

    •

    2 Posts

    612

    0

    Posted March 10th, 2005 19:00

    You should probably RMA that switch then :)

    I'm wondering if anyone from Dell watches over this section? or do they just ignore major problems with the powerconnect line?

    -scott
  • Asounds

    1 Rookie

    •

    16 Posts

    612

    0

    Posted March 10th, 2005 20:00

    It's been running for almost 2 hours now without rebooting. Will let it run through the weekend before I do anything else with it. I only have 2 workstations connected to it at this time.

    This is my first managed switch I have had to deal with, so I am learning as I go.
  • GregG1

    2 Intern

    •

    812 Posts

    612

    0

    Posted March 11th, 2005 13:00

    Carphost,
    As stated in the post titled "PowerConnect-Managed Switches: PLEASE READ BEFORE POSTING" at the top of this message board, this forum is not intended to be a method for directly contacting Dell technical support. It is intended for Dell customers to request assistance from other Dell customers. The moderators may answer quick questions from time to time, but this should not be expected. If you need immediate assistance, please contact technicial support by phone at (800) 822-8965 and follow the prompts for Server and PowerConnect.
     
    All issues with the 3300 series we have been able to duplicate to date have been resolved in the available firmware releases (the most recent being 1.2.0.6). If a customer is having issues with the switch, they are encouraged to contact technical support so the problem can be investigated. If the problem can be duplicated, it will be escalated to the engineers to determine the root cause and work to resolve it.
     
    Asounds,
    The error you were seeing:
    %2SW-F-FATAL: DILC_fatal_error: ERROR return: -27 soc_gbp_size_probe - Memory test failed
    appears to be a hardware error related to the memory. If you continue to see this error, I would suggest contacting tech support to have the switch replaced.
  • Asounds

    1 Rookie

    •

    16 Posts

    612

    0

    Posted March 11th, 2005 14:00

    Asounds,
    The error you were seeing:
    %2SW-F-FATAL: DILC_fatal_error: ERROR return: -27 soc_gbp_size_probe - Memory test failed
    appears to be a hardware error related to the memory. If you continue to see this error, I would suggest contacting tech support to have the switch replaced.





    I haven't had any errors since that one and it has not rebooted either.
    I am still learning how to use a managed switch, and I am happy there is this forum! I am sure I will be using it.

    Thanks
  • treySter

    4 Posts

    612

    0

    Posted May 12th, 2005 13:00

    I have 3 of these 3348 switches stacked and I seem to be having mysterious reboots as well. We have the latest version of firmware installed (1.2.0.6) on all 3 switches. It doesn't happen very often but once or more is enough to be a problem. When it happens, we look at the top switch (Stack ID 1) and the stack light is blinking amber color. It seems like it is doing this during a reboot. Does anyone else experience this?
  • topherness54

    1 Rookie

    •

    1 Message

    •

    2 Points

    0

    0

    Posted December 21st, 2024 00:52

    What a coincidence!

    BOOT Software Version 1.0.0.13 Built  11-May-2003  14:58:20
    Processor: MPC8245 Rev 0.14, 250 MHz (Bus: 100MHz), 32 MByte SDRAM.
    I-Cache 16 KB, linesize 32.D-Cache 16 KB, linesize 32.
    Cache Enabled.

    Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom.
    Preparing to decompress...

    Decompressing SW from image-1
    8ae000
    OK
    Running from RAM...

    .
    Update Host params for stand-alone

    ******************************************************************
    *** Running  SW  Ver. 1.2.1.3  Date  11-Apr-2005  Time  11:46:48 ***
    ******************************************************************

    HW version is 00.00.01
    Base Mac address is: 00:0d:56:45:1c:4b
    Dram size is  : 32M bytes
    Dram first block size is  : 20M bytes
    Dram first PTR is  : 0xB20000
    Flash size is: 8M

    STAND ALONE
    01-Jan-2000 01:01:11 %2SW-F-FATAL: DILC_fatal_error: ERROR return: -3 bcm_cm_dev
    ice_supported failed
     - Feature unimplemented or unavailable.

    ***** FATAL ERROR *****
    Reporting Task: ROOT.
    Software Version: 1.2.1.3 (date  11-Apr-2005 time  11:46:48)
    0x454ec
    0x4551c
    0x48140
    0x2b7390
    0x1c54a4
    0x1c5958
    0x1c94dc
    0x316570

  • DELL-Joey C

    Moderator

    •

    4170 Posts

    •

    20965 Points

    0

    0

    Posted December 23rd, 2024 02:07

    Hi,

     

    Are you facing the same situation where the switch still operate after a few reboots? 

     

    Based on the error, I'm not entirely sure the cause of the issue. But, if referring to a couple of error information: 01-Jan-2000 01:01:11 %2SW-F-FATAL: DILC_fatal_error: ERROR return: -3 bcm_cm_device_supported failed

     

    The time strap seems to be at year 2000, I'm unsure if there is an issue with the hardware, or it is having an issue with communicating to NTP. For this error "DILC_fatal_error", the switch is having an issue with DIL Copy. This operation typically refers to a process within embedded systems or network devices where it involves the copying and loading of firmware or software images that are independent of specific hardware configurations. The DILC error indicated "bcm_cm_device_supported failed"; this is showing that the system encounters a fatal error when checking for a supported Broadcom device. Or, entirely, the switch firmware has failed and unable to recover. 

     

    Have you tried removing all the switch cables and check the issue?

    DELL-Joey C

    Social Media and Communities Professional

    Dell Technologies | Enterprise Support Services

    #IWork4Dell

    Did I answer your query? Please click on ‘Mark as Accepted Answer’ if I did.