UNSOLVED

Willi2793

updated

6 years ago

W

Willi2793

32 Posts

0

5139

August 25th, 2017 01:00

2 FN410T in FX2 in VLT-Mode

Hello,

we have a FX2 with 2 FN410T as IOMs. I changed the mode from Standalone to VLT and I'm not sure if this works correctly. I did it strongly like advised in the Deployment-Guide found here:

http://en.community.dell.com/techcenter/networking/m/networking_files/20440794

But the Backup-Link in the 2 modules are a 169-IP-address wich is a little suspicous for me. Also I tried to reboot one of the 2 IOM. I first set the 2 external ports to down wich sets also the internal ports down. That makes me a bit wondering. But the connection was still okay and the other IOM did all the work.

Than I reloaded the first IOM wich was offline and after it was back the connection to the servers was lost for appr. a minute. And this is totaly weird in my opinion.

The Dashboard of the 2 IOMs say it is all okay and VLT is up and running with all necessary links and heartbeats and so on. But why is after a reload the connection lost for a while?

  • Willi2793

    32 Posts

    3872

    0

    Posted August 25th, 2017 07:00

    Yes, I expected the backup-link to be the Management-IP. And I configured one on each of the IOM. And they are both pingable by each other. Than I used the VLT-Mode wich is kinda autoconfiguration. The PO 127 as VLT-Peer-Link is configured and working. But this mode seems not allowing me to configure the VLT-Domain. 

    I got the address by a standard "sh run". Here's the vlt-domain part:

    vlt domain 1
     peer-link port-channel 127
     back-up destination 169.254.31.22
     system-mac mac-address 00:01:06:01:02:09
     unit-id 0

    I'll have a look at the document you mentioned. Thx. But I suppose I'm not allowed to change this parameter in this mode.

    And I thought that VLT is the possibility to have maintenance (incl. a reload) on one of the IOMs without service interruption? And now a reload without any maintenance gives me the interruption!?

  • Willi2793

    32 Posts

    3872

    0

    Posted August 25th, 2017 09:00

    No, sorry. I do not have this command. In EXEC and CONF I have the following:

    asset-tag                       Write AssetTag information
    bmp                             BMP commands
    cd                              Change current directory
    clear                           Reset functions
    clock                           Manage the system clock
    clone-config                    Configure cloning related commands
    configure                       Configuring from terminal
    copy                            Copy from one file to another
    debug                           Debug functions
    delete                          Delete a file
    diag                            Run diagnosis
    dir                             List files on a filesystem
    disable                         Turn off privileged commands
    enable                          Turn on privileged commands
    exit                            Exit from the EXEC
    format                          Format a filesystem
    monitor                         Monitoring feature
    no                              Negate a command
    offline                         Take stack-unit offline
    online                          Bring stack-unit online
    ping                            Send echo messages
    power-cycle                     Power-cycle the unit(s)
    pwd                             Display current working directory
    redundancy                      stack-unit failover
    release                         Release the ip address back to dhcp server
    reload                          Halt and perform a cold restart
    rename                          Rename a file
    renew                           Renew the lease of IP address obtained through dhcp
    reset                           Reset selected card
    restore                         Restore sub commands
    show                            Show running system information
    ssh-peer-stack-unit             Open a SSH connection to the peer stack-unit
    stack-unit                      Stack-Unit
    start                           Start shell
    stop                            Stop the BMP functionality
    tcpdump                         Capture the TCP traffic at CPU
    tdr-cable-test                  Start diagnostics (TDR test) for the cable
    telnet                          Open a telnet connection
    telnet-peer-stack-unit          Open a telnet connection to the peer stack-unit
    terminal                        Set terminal line parameters
    traceroute                      Trace route to destination
    undebug                         Disable debugging
    upgrade                         Upgrade subcommands
    upload                          Upload file
    write                           Write running configuration to memory or terminal
    S152244#conf
    S152244(conf)#?
    aaa                             Authentication, Authorization and Accounting
    banner                          Define a login banner
    boot                            Modify system boot parameters
    clock                           Configure time-of-day clock
    dcb                             Data Center Bridging
    default                         Set a command to its default
    enable                          Modify enable parameters
    end                             Exit from configuration mode
    exit                            Exit from configuration mode
    feature                         Feature enable options
    ftp-server                      FTP configuration subcommands
    hostname                        Set system's network name
    interface                       Select an interface to configure
    io-aggregator                   I/O Aggregator Blade Switch configuration
    ip                              Global IP configuration subcommands
    lacp                            Configure LACP
    line                            Configure a terminal line
    logging                         Modify message logging facilities
    management                      Create a management crypto or route, etc
    monitor                         Monitor monitored ports
    ntp                             Configure NTP
    protocol                        Select a protocol to configure
    radius-server                   Set up RADIUS server
    redundancy                      Set up stack-unit redundancy configuration
    reload-type                     Enter reload-type submode
    script                          Start or stop a script
    service                         Service selected component
    snmp-server                     Modify SNMP parameters
    stack-unit                      Configure stack-unit
    tacacs-server                   Set up TACACS+ server
    uplink-state-group              Uplink state group creation and configurations
    username                        Establish user name authentication
    S152244(conf)#

    Nothing to change to VLT or BACKUP. And as I said: the management-ip is set. Also Gaeway, routing, DNS, ...

    The logs of the IOM wich should stayed up mention the following:

    Aug 25 03:49:03: %STKUNIT0-M:CP %IFMGR-5-OSTATE_DN: Changed interface state to down: Te 0/9
    Aug 25 03:49:03: %STKUNIT0-M:CP %IFMGR-5-OSTATE_DN: Changed interface state to down: Po 127
    Aug 25 03:49:04: %STKUNIT0-M:CP %VLTMGR-6-VLT_ICL_DOWN: InterChassis Link is down (link down).
    Aug 25 03:49:06: %STKUNIT0-M:CP %VLTMGR-6-VLT_HBEAT_DOWN: Heart beat link is down (down).
    Aug 25 03:49:06: %STKUNIT0-M:CP %VLTMGR-6-VLT_ELECTION_ROLE: Chassis is transitioning to primary role.
    Aug 25 03:49:06: %STKUNIT0-M:CP %VLTMGR-6-VLT_PEER_STATUS: Peer chassis is down.
    Aug 25 03:50:49: %STKUNIT0-M:CP %LLDP-5-LLDP_PEER_AGE_OUT: DCBX operationally disabled due to LLDP peer timing out on interface Te 0/9
    Aug 25 03:51:02: %STKUNIT0-M:CP %IFMGR-5-OSTATE_UP: Changed interface state to up: Te 0/9
    Aug 25 03:51:02: %STKUNIT0-M:CP %IFMGR-5-OSTATE_UP: Changed interface state to up: Po 127
    Aug 25 03:51:19: %STKUNIT0-M:CP %IFMGR-5-OSTATE_DN: Changed interface state to down: Te 0/9
    Aug 25 03:51:20: %STKUNIT0-M:CP %IFMGR-5-OSTATE_DN: Changed interface state to down: Po 127
    Aug 25 03:51:24: %STKUNIT0-M:CP %IFMGR-5-OSTATE_UP: Changed interface state to up: Te 0/9
    Aug 25 03:51:24: %STKUNIT0-M:CP %IFMGR-5-OSTATE_UP: Changed interface state to up: Po 127
    Aug 25 03:51:31: %STKUNIT0-M:CP %VLTMGR-6-VLT_ICL_UP: InterChassis Link is up.
    Aug 25 03:51:32: %STKUNIT0-M:CP %VLTMGR-6-VLT_PEER_STATUS: Peer chassis is up.
    Aug 25 03:51:32: %STKUNIT0-M:CP %VLTMGR-6-VLT_HBEAT_UP: Heart beat link is up.

    And yes, I pinged a VM from the external side and have successful pings during the complete reload-process. when the IOM was up this ping was unseccessful for a while and came back than.

  • Willi2793

    32 Posts

    3872

    0

    Posted August 27th, 2017 06:00

    Hi,

    thx for your suggestions. But I cannot Change to the vlt-mode. I showed you all comands I can issue in EXEC and conf-mode. But no VLT.

    And RSPT is not enabled in the Moment.

    Thx and regards

  • MK.W

    27 Posts

    3872

    0

    Posted August 29th, 2017 18:00

    suggest you change to full switch mode then manual configured VLT setting as you want.

  • xprxprx

    1 Message

    3411

    0

    Posted January 8th, 2019 02:00

    Hi,

    we are faceing the same problem with the VLT configured on the management interface IP. When the pair comes up we are experiencing a 30 sec timeout.

    Did you find a solution for your case? Would you share it?

    Thanks,

    Xavi.

  • Willi2793

    32 Posts

    2959

    0

    Posted February 18th, 2019 08:00

    Hi Xavi,

     

    sorry, currently I haven't found a solution. Bute I opened a case and now I should first update my firmware. Let's see. This is planned for next friday

  • Willi2793

    32 Posts

    753

    0

    Posted February 24th, 2019 03:00

    I upgraded now from 9.10 to 9.14 and the Failover is okay.

    I still have an issue with Networking on ESXi but this is a different isue I guess.

  • SJNetGeek

    1 Message

    445

    0

    Posted July 11th, 2020 21:00

    When configuring the FN modules using the "canned" VLT mode it does not pick up the management IP addresses of the units and assigns a temporary DHCP address to the links which fails.  If your FN401T modules have statically configured IP addresses for management, you can work around this issue by copying off the running config to another host, editing the vlt configuration section of the file to include the peer address, and then copy it back to the running config and save it.

    vlt domain 1
      peer-link port-channel 127
      back-up destination x.x.x.x   <--- add this line with the IP address of the VLT peer here.