Matt3014

updated

14 years ago

M

Matt3014

3 Posts

0

14449

April 11th, 2013 05:00

Problems with my new 3014 monitor

my 3014 arrived today. not having a great experience. not sure how good my now-dead 3008 was performing, but this seems a bit odd. I never noticed anything funny about the old one

couple of things:

1. black performance.

booted up a game of Chivalry, any areas that were dark at all had almost no darkness gradation (ie, anything that was quite dark, was nearly all black), but light areas were fine and looked nice.

on this test image -
http://img15.imageshack.us/img15/962/calibration.gif
no permutation of brightness, contrast, ambient light or colour profile can let me see any difference at all between A, B, C, D and E.

likewise, on this test image -
http://blog.bigsmoke.us/uploads/2009...-calibrate.png
i can not see anything other than all-black on the 1% through 11%, the whole screen is a wall of identical black except for the colour bands, regardless of brightness, contrast, ambient light or colour profile. the top colour test, it's all completely black for a solid 2cm to the right of the aqua line where the coloured bars are supposed to become visible.

presumably i'm being super-dumb about something, but is this consistent with other people's (3014 or non-3014) results?

2. ghosting

I never noticed this on my old 3008, but scrolling up and down a website (dark text on light background) leaves a definite trail following any text. it's a decent 1mm or so in length if i purposefully make my scroll speed maximise the effect. it's still readily apparent with slower scrolling, just not as long a trail, and with really fast scrolling it's disguised by the magnitude of the image shift so isn't particularly noticeable.

just scrolling up and down this preview pane to type this, it's extremely noticeable. i'm 100% sure I would have noticed this on my old monitor.

it is very distracting during normal web surfing use.

open to any thoughts regarding settings or anything I might be doing wrong.

probably coincidental, but i also have 2 stuck bright pixels - very noticeable white on colored backgrounds, but very hard to see on a black background (i think this is related to the poor black performance).

i purchased in Australia, and I have posted this same content on a local tech forum to get input from there as well. I would be very keen for a response from a Dell representative. I was very happy with my old 3008, and never had a problem with it until it died recently.

(also, I read this thread http://en.community.dell.com/support-forums/peripherals/f/3529/t/19499832.aspx which talked about built-in diagnostics in the 3014 - following those instructions, I am unable to enter the diagnostic mode, it just stays in power saving mode, counting down to 5 minutes? pressing buttons 1 and 4 while DVI is unplugged seems to have no effect)

thanks for any help.

  • Matt3014

    3 Posts

    877

    1

    Posted April 15th, 2013 05:00

    False alarm on the poor black performance - was a driver issue. Black level performance on this model is fine/good. AMD/ATI driver was defaulting to a large negative on software brightness. Still not having luck with faulty pixels, but that's not as much of a problem - a simple replacement will fix that. The ghosting is not as bad also, now that I've fixed that driver problem.

  • Matt3014

    3 Posts

    877

    0

    Posted April 11th, 2013 06:00

    ok a further test (which makes me think my unit is very badly calibrated, or faulty) -

    www.drycreekphoto.com/.../monitor_black.htm

    this test says a good monitor can start telling the difference straight away, and an average monitor will kick in at step 5 to 8.

    mine is completely black until step 18, which then is completely visible (and then gets brighter at each stage until the end at step 23).

    the result is identical if i am in a completely dark room, whether my contrast is high or low, whether my brightness is high or low.

    And this test page, the only reason i can tell there are supposed to be boxes at all is because of the red numbers:

    http://www.lagom.nl/lcd-test/black.php#blacktest.png

    if not a faulty unit, what settings other than brightness and contrast should i be changing?

  • adobepro

    29 Posts

    877

    0

    Posted April 11th, 2013 09:00

    Matt, #2 / Ghosting is a known issue and according to Chris, this will not be fixed / mediated with a firmware fix. I have it too and it's terrible. The only mediation available is to adjust the brightness/contrast, where the brightness is `10-20 units higher than the contrast [e.g., brightness 50, contrast 38]-- you'll have a darker screen, but the ghosting will be minimized. users nokey and dobr on this forum noted the same thing -- basically, by adjusting the brightness / contrast the RBG levels where the ghosting occurs will not be seen.

    en.community.dell.com/.../19499353.aspx

  • 877

    0

    Posted April 17th, 2013 16:00

    just got mine, using with my mac book pro retina and it looks horrible...there are these very noticeable fine horizontal lines,, i did turn off the sharpness completely and that seemed to help a little