UNSOLVED

raathass

updated

20 years ago

R

raathass

3 Posts

0

19444

September 20th, 2006 05:00

2407 and both VGA and DVI in picture-by-picture mode

Hi.
 
Why can't I use vga for one of the inputs and dvi for the other?
 
 
/t
  • SR45

    2 Intern

    •

    12138 Posts

    921

    0

    Posted September 20th, 2006 09:00

    Because the User Guide says you can't.  In part it reads below
     
    • Turn off your computer and disconnect the power cable.
    • Connect either the white (digital DVI-D) or the blue (analog VGA) display connector cable to the corresponding video port on the back of your computer. Do not use both cables on the same computer. The only case in which both cables can be used is if they are connected to two different computers with appropriate video systems.
    • Connect the upstream USB port (cable supplied) to an appropriate USB port on your computer .
    • Connect USB peripherals to the downstream USB ports (rear or side) on the monitor. (See rear or bottomview for details.)
    • Plug the power cables for your computer and monitor into a nearby outlet.
    • Turn on the monitor and computer.
      If your monitor displays an image, installation is complete. If it does not display an image, see Solving Problems. 

      <ADMIN NOTE: Broken link has been removed from this post by Dell>

    • Use the cable holder on the monitor stand to neatly organize the cables.
  • raathass

    3 Posts

    921

    0

    Posted September 20th, 2006 09:00

    Thanks for the response, but the questions was why I cannot use the vga input from one computer and the dvi input from another computer simultaniously (either PIP or PBP).
     
    I can use DVI _and_ S-Video/Composite/Component (and maybe VGA _and_ S-Video/Composite/Component, haven't tested) but not DVI and VGA or any combinations of S-Video, Composite and Component.
     
    Why not enable to select input A and input B independent of each other, and then eihter PIP, PBP or off.
     
     
    /t
  • SR45

    2 Intern

    •

    12138 Posts

    921

    0

    Posted September 20th, 2006 11:00

    Apologize for not addressing the question directly, but this is unkown to me, and possibly the same reason I gave from the Dell User Guide that the Dell monitor won't allow it,.  Perhaps someone else has a work around for you, so be patient and hope someone will weigh in on this.   Good luck
  • Juho G

    3 Posts

    921

    0

    Posted September 21st, 2006 06:00

    I was wondering, why can't both the DVI and VGA cables be connected to the same computer? I generally prefer DVI due to slightly sharper image, but there are some occasions, mainly in my graphic design work, where I'd like to check out the image in VGA-mode also due to slight differences in color reproduction etc.. So I'd like to have both cables connected with my display adapter set to clone mode. Will this cause trouble, as it is prohibited in the user guide?
  • skotwo

    30 Posts

    921

    0

    Posted September 21st, 2006 19:00



    @Juho G wrote:
    I was wondering, why can't both the DVI and VGA cables be connected to the same computer? I generally prefer DVI due to slightly sharper image, but there are some occasions, mainly in my graphic design work, where I'd like to check out the image in VGA-mode also due to slight differences in color reproduction etc.. So I'd like to have both cables connected with my display adapter set to clone mode. Will this cause trouble, as it is prohibited in the user guide?




    I've hooked up my 2407 via DVI and VGA (using DVI adapter) to my video card, and it works (i.e. I can toggle between the 2 outputs (inputs) using the input button the monitor frame).

    Actually, it even works if I'm not in clone mode, but I can't think of a use for doing this.


    I guess the problem is with the picture by picture mode
  • all the facts

    2 Intern

    •

    983 Posts

    921

    0

    Posted September 22nd, 2006 04:00

    "Do not use both cables on the same computer. The only case in which both cables can be used is if they are connected to two different computers with appropriate video systems."

    That message in bold print probably actually means something.

    For PIP or PBP, DVI or VGA=(1 source) and Component or composite or s-video=The other source.

    That's the way I understand it.

    Some one hooked up both VGA and DVI from same PC and knew the warning and tested for Banding, but only a short time. I wouldn't do it, unless Dell warranties the procedure and use of the product in a specific way.

    Message Edited by all the facts on 09-22-2006 12:56 AM

  • _doug_

    8 Posts

    921

    0

    Posted September 22nd, 2006 14:00

    I have both DVI and DSUB connected to the same machine. There is no problem doing this and I have no idea why the manual states not to do so.

    I had hoped to use PIP this way but I guess the monitor just doesn't support it.

    Fortunately my video card also has HD component out. So one day I will get around to connecting all 3. Component should work with PIP.
  • all the facts

    2 Intern

    •

    983 Posts

    921

    0

    Posted September 22nd, 2006 22:00

    I have both DVI and DSUB connected to the same machine. There is no problem doing this and I have no idea why the manual states not to do so.

    I don't see why not. Anyone else have a reason why not to do this, besides the manual warning?

    Component should work with PIP form video card.

    I would think so.

    Message Edited by all the facts on 09-22-2006 06:06 PM