
UNSOLVED
Closed
inspiron 9100 - radeon 9700 - my screen shuts off after winXP logo screen at boot up
my screen is turning off right after the winXP logo screen displays at startup. i rebooted, tapped F8, and selected 'enable VGA mode'. windows starts, but in 640x480. when i try changing the resolution to anything above that, i'm back to the black screen again. any ideas? thanks so much
Responses (8)
Solutions (0)
- jlackey-sorry to hear that you're in the same boat as i am. i tried reformatting and re-installing, and still had the problem. i got XP all reloaded, and i started reloading the drivers. after i installed the video drivers i rebooted, and boom.. screen was black after the XP logo. i wasn't a happy camper! i'm still looking for answers, and i'll post back if i get anywhere. good luck!
- Well, this stinks - the official reply from tech support: do a complete fresh reinstall of Windows XP, losing all data, etc. That sounds like someone without a clue reading from a chart. Ugh. So I'll do this, spend hours backing up data, etc., it won't make a difference (since this is clearly a hardware problem) and then be right where I am now.
- I've encountered a similar problem lately.When I install the video drivers after a fresh XP Pro reload, the computer freezes right at the XP Logo. That little progress bar stops dead in its tracks.But I discovered a workaround. This might work for you guys.After you Install XP Pro, and you're taken to the desktop for the first time, install the video drivers right then and there. No SP1 or SP2, no Microsoft updates, no chipset drivers, nothing. Video drivers first and foremost, and a reboot of course. Once those are installed, you should be in the clear. Hopefully. Like I said, this worked for me.
whymewhynot
2 Intern
•
174 Posts
739
0
Posted November 2nd, 2004 13:00
I think it was one of the mods that recently posted that fix, it wasn't very logical specifically for the reason you mentioned, that the screen works just fine sans drivers. I presume that the switch is actually ported through the ATI driver ?
Anyway all credit to the person who did actually resolve, for you at least, that problem
- Well, I found the solution, and it makes no logical sense whatsoever (to me) so I would have never figured it out on my own. I found it after doing a search on this forum and reading for about an hour and seeing different things people have tried.There is a small "pin" that sticks out of the right hole above the power button. The top of it was barely clearing the hole, but I didn't think that was unusual. But reading what someone had posted here, I used a knife edge to pull it up further out of the hole, and sure enough it popped out another little bit (to where it is clearly an eighth of an inch or so out, and where you can easily push it down and watch it spring back up.) This is the pin that detects if the lid is closed.That completely fixed the problem. I reinstalled the drivers, rebooted, no problem. Turned the computer off, back on, booted up fine. Upgraded to the Omega drivers, no problem. It's fixed (thanks to whoever posted that solution in an earlier thread.)Now - why in the heck would that pin being stuck down allow me to boot up in safe mode with no problem but hang up when I tried to boot up with ATI drivers installed makes no sense. It makes no sense that with no drivers installed I could change to higher resolution and boot up with no problem, but as soon as I installed either the Dell drivers or the Omega drivers it MAY boot up fine, but most of the time give me a turned off LCD as soon as it went to the Windows XP logon screen. Makes no sense why I could install the drivers and boot up in 640x480 mode but as soon as I made any resolution change the screen turned off. Makes no sense, but freeing that pin up definitely fixed the problem. And I would have NEVER figured that out on my own.And apparently neither would the robot tech support - it really, really irritates me that I describe this problem and get a blanket "format your drive and reinstall Windows XP fresh" reply, and they won't do anything further unless I do that (and waste hours, plus risk losing data.) Then they want to replace my hard drive - what in the H*** has that got to do with a video problem??? I could see "OK, let's replace your video card" or "Let's replace your LCD" but replace my hard drive??? I really feel sorry for the people who are not computer savvy that blindly take such advice.Anyway - hope this solves this odd problem for other folks. I may post a new thread with a title to make it easy for others to find it in a search.
Same problem here with an Inspiron XPS/MR9700 (flash/driver both Dell's A03). After the windows logo switches to the login screen (at the point where the display changes to 1900x1200 from a lower resolution) the screen goes black (usually- once it went orange!). It's an intermittent problem- after booting into safe mode, re-logging in at a low resolution, and then restarting, the system usually works normally.
The little stick-swtich (I assume it tells the monitor to turn off when the 'lid' is closed) above the power button seems to have no effect on this- although I suppose it _could_ be the culprit. Does anyone know exactly what that switch does and why it might cause trouble with high resolutions? I installed XP-SP2 a couple of months ago but this problem hasn't appeared until very recently.
Norton reports no viruses, and Dell Diagnostics reports no problem with any hardware. Previous posts have argued that re-installing windows doesn't work with the same problem, so I'm not doing that if I'm going to get no favorable results.My gut feeling is that this is a driver problem or a hardware problem- and since I'm out of the country for a few months and my service plan is only applicable in the US, I can only hope it's the former. Does anyone know when driver A04 might come out or a new vbios flash? Any info that might help from anyone is certainly appreciated. Thanks.
- is that stick switch completely out of the hole (as in about an 1/8th of an inch or so?) I thought mine was fine, but when I pulled it further out of the hole with the edge of my knife, it popped free. Your symptoms sound exactly like mine did (and see the other thread of mine on this topic where someone gives a logical explanation of why it does this.) I was convinced it was drivers, a corrupted OS, video hardware, BIOS, etc. but it was simply that little lid closure detection switch.

jlackey
50 Posts
739
0
Posted November 1st, 2004 15:00