UNSOLVED

MsRed

updated

21 years ago

Closed

M

MsRed

16 Posts

0

2481

October 3rd, 2005 15:00

5150 w/ blank screen, seems to boot up

My 5150 is about 16 mos. old and had been in standby mode yesterday when I went to work on it again.  There seemed to be a bit of light eminating from the screen, but I could not see any windows that had been open, etc.  I tried to power up again, same result.  I took the cable from this pc and hooked it to the 5150 and got nothing.  Is there anything else I need to do when trying this?  I see mentioned in a few posts about holding the Fn/F8 down together.  When would I do that and what should happen?  I only pulled the battery and reinserted it, haven't tried reseating anything else.  Could the video card have gone bad?
 
Thanks!!!
  • mchakko

    5 Posts

    340

    0

    Posted October 3rd, 2005 22:00

  • mchakko

    5 Posts

    340

    0

    Posted October 3rd, 2005 22:00

    That sounds exactly like my problem...I posted a few days ago but got no response :(
     
     
    Have you tried plugging an external monitor into your computer?   When I did this, everything worked fine.  The first time I even managed to fiddle with settings and get things working on the laptop's lcd when I rebooted, but then it stopped working again.  At first I thought maybe I had been on to something, but now I think I have a hardware problem with the LCD and that with hardware failures sometimes things work again for a minute, then fail again (like was the case when my motherboard failed.)
     
     
    I am still intrigued about why when I got the blank screen, I could hear windows boot up and come up ("pop" noise even with the screen not working)  with an X in the system tray about 'do you want windows to reconfigure your display"
  • MsRed

    16 Posts

    340

    0

    Posted October 4th, 2005 00:00

    Well, I tried plugging the monitor cable from my desktop pc (Dimension XPS T500, ancient!) and got nothing. 

    I'm so frustrated with this laptop, this is not my first problem with it.  I sent it to Joe at AQS for the pressure shut down issue just a couple months ago.  And just got this thing paid off!  If I can at all avoid it, I will not make my next pc purchase a Dell.  I haven't tried tech support to resolve this issue, since my last go with them was not successful.  I hope someone responds that has an idea of what's causing this.

    Thanks for sharing your post.

  • lisamm

    3 Posts

    340

    0

    Posted October 4th, 2005 14:00

    MS Red:
     
    I just did a long post to your original question, but  I forgot to mention that the computer guy I talked to said this is a common problem with any LCD display.  They are not made to withstand such heat.  In this case - it's not just the Inspiron, not just Dell.
     
     
  • lisamm

    3 Posts

    340

    0

    Posted October 4th, 2005 14:00

    I don't know how to copy what I wrote to MS Red, but if you are still interested in this problem please read my post of a few minutes ago.  I have come up with some info and a temporary possible work around on this issue.
  • lisamm

    3 Posts

    340

    0

    Posted October 4th, 2005 14:00

    I have a similar problem.  I don't have a perfect fix yet, but I do have some helps to get you by until a fix is found.  I have had my Inpriron 5150 for about 17 months so a similar time frame.  Of course I didn't rewnew the service contract when it expired after the 1 year.  Looking back I probably should have but oh well, life goes on.  I have read everything I can find in the last week or so, and talked to anyone I could get to listen to me.
     
    I use my computer constantly every day.  I take it every where I go for business or personal.  My children use it to watch movies when we are on the road, I use it for business on the road.  I was leaving my computer on all day and turning it off only at night.  Apparently this is not good for our laptops, particularly for LCD displays.
     
    The problem we are having appears to be heat related.  I have never had this problem before, so I assume it adds to the wear and tear over time.  I know it is a problem in the screen (LCD) and not in the computer itself as I have hooked it up to a projector I use for meetings (works like an external display) and everything works just fine.
     
    The first time it happened I left my computer unplugged and off for two days - afraid to turn it back on and find out it was dead forever.  But it wasn't.  When I did turn it back on it worked perfectly - for a while, then it blanked out again.  I have found over the last week if I turn my computer off when I am not directly using it rather than leaving it on so I can conveniently check my e-mails my screen will work for me.  I now make sure to give my computer breaks each day and find other things to do (catch up on my shredding, filing, etc.) so as not to continue the abuse I have been dishing out to this poor machine.
     
    A computer guy I talked to locally said to go into the power settings and reduce the time the screen is set to stay on without use (go to control panel, power options, power schemes, turn off monitor after:  I did 5 minutes).  This is different than screen saver.  What this does it turn your screen off after non use.  Your screen will turn back on when you touch any button.  This will not repair the damage already done, but it will help you get by for now.
     
    If I find a fix short of replacing the screen (which is not a reasonable option because you can have a newer more up to date laptop for not much more than a screen replacement will cost) I will post again.
     
    Good Luck!!
     
  • MsRed

    16 Posts

    340

    0

    Posted October 9th, 2005 20:00

    Update:

    I've now been able to attach the monitor from my desktop and work from the 5150.  I can see the desktop, work in all the programs, etc.  I also had a chat session with Dell this morning about the issue.  They suggested I do two things.  One, press the F2 key at the start of reboot.  If the BIOS screen didn't display on the LCD, then the LCD would need to be replaced.  Second, I could download and reinstall the video drivers and see what that would do.  Which is nothing.  I haven't tried the reboot/F2 process yet, but from doing my earlier research, I'm betting the LCD needs to be replaced.  Which, compared to having to replace the video card, seems not so bad.

    Thanks all for the responses.