UNSOLVED

dans221

updated

13 years ago

D

dans221

23 Posts

0

180558

March 11th, 2012 21:00

studio xps 435mt ssd installation

I'm trying to install a Samsung 830 ssd in the hdd1 bay of the studio xps 435mt but I'm having difficulty physically installing the ssd.

The ssd is 2.5" but comes with 3.5" bracket and power and esata cables.

The problem for me is how to attach the 3.5" bracket to the hdd1 bay. I just don't see where or how it's supposed to fit. I must be missing something here?

  • dans221

    23 Posts

    1306

    0

    Posted March 11th, 2012 22:00

    This is the link to the service manual describing how to replace an hdd:

    <ADMIN NOTE: Broken link has been removed from this post by Dell>

    The issue is that once I put the SSD on the 3.5" bracket there are only side screw holes available on the bracket. From what I see online, usually the hdd bays are horizontal but this seems vertical. Here's some pictures:

    I'm trying to install it in the bottom bay there which is empty
    http://i39.tinypic.com/2hpu4vq.jpg

    This is a view of the samsung830 with bracket from the top:
    http://i44.tinypic.com/16jk5m0.jpg

    And from the bottom:
    http://i44.tinypic.com/28veoms.jpg 

  • Jay6600

    126 Posts

    1306

    0

    Posted March 11th, 2012 22:00

    Have you checked your service manual? Sureley its explain replacing the hdd,,if your drivebay is already fully occupied ,those ssds are superlight and with no moving parts if theres some unobsructing room in the case just attach some hook n loop tape to either itll be fine

  • dom99

    34 Posts

    1306

    0

    Posted March 18th, 2012 04:00

    I have also just bought an ssd and am worried that when it gets here it won't work properly. There is no ahci setting in the bios only sata or raid. I will this affect how it works with trim and the intel toolbox.

  • Davet50

    6 Operator

    •

    14442 Posts

    1306

    0

    Posted March 18th, 2012 08:00

    dans221

    The advice that Jay6600 gives is about the best that you can do. Like mentioned SSDs are light cool running and since that have no moving parts they can be just left in place. There is another thread somewhere here where a user just used double sided sticky tap to stick the mounting bracket to the hard driver cage and it is running just fine.

  • Davet50

    6 Operator

    •

    14442 Posts

    1306

    0

    Posted March 18th, 2012 08:00

    The SATA mode will be Ahci by default. To verify this in your system open up Device manager and go to the listing for IDE ATA/ATAPI controllers. Expand that and it will show a listing for the SATA controller.

  • dom99

    34 Posts

    1306

    0

    Posted March 18th, 2012 09:00

    Mine says:

    ATA channel 0

    ATA channel 0

    ATA channel 1

    ATA channel 1

    Standard Dual Channel PCI IDE Controller

    Standard Duel Channel PCI IDE Controller

    Isn't it AHCI and not IDE that I need. I'm not sure what it all means

  • Kelbear1

    1524 Posts

    1306

    0

    Posted March 18th, 2012 11:00

    Here is what someone did on their 435mt:

    I set my BIOS SATA setting to RAID, even though I have 2 independent (non-RAID) SATA drives and 2 independent external SATA drives. I then installed the latest Intel Matrix Storage Manager from the Intel website, which combined with the RAID setting in the BIOS enabled AHCI on all 4 of my SATA drives. Besides noticeably higher speed, I now have hot-swapping on the eSATA port as well as the SATA port I use for the second external drive (I do use the Safely Remove Hardware icon rather than just pull the drive, of course).

  • dom99

    34 Posts

    1306

    0

    Posted March 18th, 2012 13:00

    Thanks for that!

    Once I have done that how do I confirm that it is running in AHCI? Is it in the device manager?

  • Kelbear1

    1524 Posts

    1306

    0

    Posted March 18th, 2012 20:00

    In Device Manager under under your IDE/ATA ATAPI controllers.  Should show Standard AHCI Serial ATA Controller.

  • Davet50

    6 Operator

    •

    14442 Posts

    793

    0

    Posted March 19th, 2012 05:00

    Is it possible for Dell team to create a casing for your SSD that will make it like an external drive?

    Possible? Yes.. In reality no way. It would not be cost effective for Dell to R&D and manufactor such a part for one system