UNSOLVED

somwicked

updated

20 years ago

S

somwicked

8 Posts

0

36274

July 20th, 2006 13:00

GX260 Error I/O Card Parity interrupt at .. & Postcard codes for BIOS?

I've got a GX260 that's started giving me errors at boot - I/O card parity interrupt at (various addresses). My options are shut off NMI, Reboot, continue.

If I shut off NMI, I can boot Windows just fine.

There are no add-in cards in this system so I know the motherboard is flaking with onboard components. I have swapped RAM, updated the BIOS to A09 (latest), etc.

I will be testing the remaining components soon with add-in cards and disabling the onboard ones - waiting on parts.

In the meantime, I installed a PCI post card in this and a good system.

The good system reports 38 3b FF.
The failing system reports 38 3c 3d FF. Obviously different. I just have nothing to tie this information to - what do the 3c and 3d refer to?

Any ideas?
  • somwicked

    8 Posts

    500

    0

    Posted July 20th, 2006 14:00

    Thanks for the info but I'm not thinking so in this case.

    I have another optiplex gx260 here without issue. I swapped RAM between the 2 machines first. The 'bad' machine still has the same issues. The 'good' machine has no issues running with each other's RAM.

    I found and took a look at electrocution.com and for a Pheonix BIOS (Dell) it states the 3C and 3D codes are serial and parallel port tests failing. Working on that.

    If after I test onboard components by replacement and disabling, I still get the error I'll run memtest.

    I should add .. I ran Dell Diagnostics (updated) and they came back clean, express and extended.

    Puzzling? Yes.
  • speedstep

    11 Legend

    •

    46969 Posts

    500

    0

    Posted July 20th, 2006 14:00

    Parity Check means Bad Ram.

    http://www.bioscentral.com/postcodes/phoenixbios.htm

    Phoenix 4.0 Release 6.0 BIOS Post Codes:

    02 Verify real mode
    03 Disable non-maskable interrupt (NMI)
    04 Get CPU type
    06 Initialize system hardware
    07 Disable shadow and execute code from the ROM
    08 Initialize chipset with initial POST values
    09 Set IN POST flag
    0A Initialize CPU registers
    0B Enable CPU cache
    0C Initialize caches to initial POST values
    0E Initialize I/O component
    0F Initialize the local bus IDE
    10 initialize power management
    11 Load alternate registers with initial POST values
    12 Restore CPU control word during warm boot
    13 Initialize PCI bus mastering devices
    14 Initialize keyboard controller
    16 BIOS ROM checksum
    17 Initialize cache before memory autosize
    18 8254 programmable interrupt timer initialization
    1A 8237 DMA controller initialization
    1C Reset programmable interrupt controller
    20 Test DRAM refresh
    22 Test 8742 keyboard controller
    24 Set ES segment register to 4GB
    26 Enable gate A20 line
    28 Autosize DRAM
    29 Initialize POST memory manager
    2A Clear 512KB base RAM
    2C RAM failure on address line xxxx
    2E RAM failure on data bits xxxx of low byte of memory bus
    2F Enable cache before system BIOS shadow
    30 RAM failure on data bits xxxx of high byte of memory bus
    32 Test CPU bus clock frequency
    33 Initialize Phoenix Dispatch Manager
    36 Warm start shut down
    38 Shadow system BIOS ROM
    3A Autosize cache
    3C Advanced configuration of chipset registers
    3D Load alternate registers with CMOS values
    41 Initialize extended memory for RomPilot
    42 Initialize interrupt vectors
    45 POST device initialization
    46 Check ROM copyright notice
    47 Initialize I20 support
    48 Check video configuration against CMOS
    49 Initialize PCI bus and devices
    4A Initialize all video adapters in system
    4B QuietBoot start (optional)
    4C Shadow video BIOS ROM
    4E Display BIOS copyright notice
    4F Initialize MultiBoot
    50 Display CPU type and speed
    51 Initialize EISA board
    52 Test keyboard
    54 Set key click if enabled
    55 Enable USB devices
    58 Test for unexpected interrupts
    59 Initialize POST display service
    5A Display prompt "Press F2 to enter SETUP"
    5B Disable CPU cache
    5C Test RAM between 512KB and 640KB
    60 Test extended memory
    62 Test extended memory address lines
    64 Jump to UserPatch1
    66 Configure advanced cache registers
    67 Initialize Multi Processor APIC
    68 Enable external and CPU caches
    69 Setup system management mode (SMM) area
    6A Display external L2 cache size
    6B Load custom defaults (optional)
    6C Display shadow area message
    6E Display possible high address for UMB recovery
    70 Display error messages
    72 Check for configuration errors
    76 Check for keyboard errors
    7C Set up hardware interrupt vectors
    7D Initialize Intelligent System Monitoring
    7E Initialize coprocessor if present
    80 Disable onboard super I/O ports and IRQ's
    81 Late POST device initialization
    82 Detect and install external RS232 ports
    83 Configure non-MCD IDE controllers
    84 Detect and install external parallel ports
    85 Initialize PC compatible PnP ISA devices
    86 Reinitialize onboard I/O ports
    87 Configure motherboard configurable devices (optional)
    88 Initialize BIOS data area
    89 Enable non-maskable interrupts (NMI's)
    8A Initialize extended BIOS data area
    8B Test and initialize PS/2 mouse
    8C Initialize floppy controller
    8F Determine number of ATA drives (optional)
    90 Initialize hard disk controllers
    91 Initialize local bus hard disk controllers
    92 Jump to UserPatch2
    93 Build MPTABLE for multi processor boards
    95 Install CD ROM for boot
    96 Clear huge ES segment register
    97 Fixup multi processor table
    98 Search for option ROM's
    99 Check for SMART drive (optional)
    9A Shadow option ROM's
    9C Set up power management
    9D Initialize security engine (optional)
    9E Enable hardware interrupts
    9F Determine number of ATA and SCSI drives
    A0 Set time of day
    A2 Check key lock
    A4 Initialize typematic rate
    A8 Erase F2 prompt
    AA Scan for F2 key stroke
    AC Enter setup
    AE Clear boot flag
    B0 Check for errors
    B1 Inform RomPilot about the end of POST
    B2 POST done - prepare to boot operating system
    B4 One short beep
    B5 Terminate QuietBoot (optional)
    B6 Check password
    B7 Initialize ACPI BIOS
    B9 Prepare boot
    BA Initialize DMI parameters
    BB Initialize PnP option ROM's
    BC Clear parity checkers
    BD Display multiboot menu
    BE Clear screen
    BF Check virus and backup reminders
    C0 Try to boot with interrupt 19
    C1 Initialize POST Error Manager (PEM)
    C2 Initialize error logging
    C3 Initialize error display function
    C4 Initialize system error handler
    C5 PnP dual CMOS (optional)
    C6 Initialize notebook docking (optional)
    C7 Initialize notebook docking late
    C8 Force check (optional)
    C9 Extended checksum (optional)
    CA Redirect Int 15h to enable remote keyboard
    CB Redirect Int 13 to Memory Technologies Devices such as ROM, RAM, PCMCIA, and serial disk
    CC Redirect Int 10h to enable remote serial video
    CD Re-map I/O and memory for PCMCIA
    CE Initialize digitizer and dispaly message
    D2 Unknown interrupt
    The following are for boot block in Flash ROM
    E0 Initialize the chipset
    E1 Initialize the bridge
    E2 Initialize the CPU
    E3 Initialize the system timer
    E4 Initialize system I/O
    E5 Check force recovery boot
    E6 Checksum BIOS ROM
    E7 Go to BIOS
    E8 Set Huge Segment
    E9 Initialize Multi Processor
    EA Initialize OEM special code
    EB initialize PIC and DMA
    EC Initialize Memory type
    ED Initialize Memory size
    EE Shadow Boot Block
    EF System memory test
    F0 Initialize interrupt vectors
    F1 Initialize Run Time Clock
    F2 Initialize video
    F3 Initialize System Management Menager
    F4 Output one beep
    F5 Clear Huge Segement
    F6 Boot to mini DOS
    F7 Boot to Full DOS
  • 500

    0

    Posted July 20th, 2006 17:00

    Its a GX260, any capacitor irregularities?
  • somwicked

    8 Posts

    500

    0

    Posted July 20th, 2006 17:00

    Nothing visible.