
UNSOLVED
BM
Bam Margera
4 Posts
0
70719
August 16th, 2004 03:00
Chipset Heatsink detached!
Hi,
My sister has a Dimension 4600C with an Intel 865G chipset. When she was transporting her computer from college to home the chipset heatsink (the little black 2 inch by 2 inch heatsink next to the main cpu heatsink and fan) detached from the motherboard.
We called Dell tech support and they didn't even know what part I was talking about and said she has to buy a whole new motherboard (her warrantly just expired 2 weeks ago). I was wondering, is it possible to re-attach the chipset heatsink using some kind of thermal paste and have the computer function as normal?
There's a little bit of adhesive on the chipbody and on the heatsink. I tried to just stick it back on there, but the adhesive is not sticky anymore, and it's really hard to line it up properly. Can I just buy some thermal paste and reattach it?
Any advice would be greatly appreciated.
Thanks!
P.S. Here's a link to a diagram of the mobo. The part in question is labeled "chip set with heat sink" in the system board components diagram.
Responses (14)
Solutions (0)
Bam Margera
4 Posts
2198
0
Posted August 16th, 2004 15:00
Thanks for your reply. I think I'm gonna get some thermal adhesive and try to reattach it myself.
When I boot my system, I get the error "Alert! Chipset heat sink not detected!" and the system halts. How does the system know that the heat sink is not attached if the only thing that connects the sink to the chip is thermal compound?
- There should be a metal "Z" clip going across the top of that heatsink. It attaches to two metal loops on either side of the MCH (the chip the heatsink came off of). The metal clip is part of a detection circuit that the system uses to know if the heatsink is there or not. Removing that clip breaks the circuit. To prevent thermal damage to the MCH, the BIOS prevents the system from booting if it detects that that clip is not there. Simply using thermal compound to hold the heatsink on won't work - the clip must be there.
Bam Margera
4 Posts
2198
0
Posted August 17th, 2004 00:00
Ah, thanks. I was wondering what the silver clip was for. I only see 1 metal loop, though. Perhaps 1 of them came off, although I don't know how that could've happened.Bam Margera
4 Posts
2199
0
Posted September 5th, 2004 05:00
Hey, does anyone know whether you can buy and reattach those little metal loops on the motherboard that the "Z" clip attaches to? If not, is there a way to simply glue down the heatsink and have the BIOS bypass the whole heatsink detection?
This is amazing! The exact same problem happend to my machine, down to the same expiration on the warranty and assistance from Dell. One minor difference, but very telling...my system hadn't been moved in months...it just POPPED off.
There is strength in numbers and I think it is something that we should raise to Dell as faulty craftsmanship on the mainboard, since the pin (mine is in location H25) has completely dislodged from the card and sent the heat sink flying inside the case.
Where do we go from here? I contacted CompUSA and they want way too much money for the repair and I understand that the is special solder for motherboards (plastic/metal/copper???). And that the Z hook piece has to be soldered from underneath the board, which means the whole card has to be removed (unless you can remove the case ????
Any help is appreciated....
johnbmoore
1 Message
2199
0
Posted July 23rd, 2005 21:00
Hello,I just had the same problem that you listed in this email.May I ask you several questions?How did you solve the problem?I see one metal loop where the "z" wire attaches, but do not see another. Will you please tell me where the two attach pointsare?Thanks in advance,Johnshesagordie
12 Elder
•
46017 Posts
455
0
Posted July 19th, 2006 20:00
NMex RonDell will only replace the motherboard, while the system is under warranty.This is a discussion about how a member repaired the motherboard retainer clip.Bev.
Same problem, same error message. Has anyone found a solution to this systemic dell problem? How about you Dell?? I see this same problem, on Google and the Dell forum, with many computers for many years.
Alert! Chipset heatsink not detected. System Halted.
The retainer came loose from the mother board and was found loose with the heatsink and retainer inside the computer case.
Any luck gluing or soldering the retainer loop back in place?
Anyone get Dell to repair their chronic problem?
The computer has stood in the same place since I bought it - I did not move it around.
Please respond!
Thanks.

cyber_surfer
551 Posts
2198
0
Posted August 16th, 2004 12:00
Reattaching is the approach I would take. Some research should help determine the best substance to use to remove the residue. If there was no other means of attachment but the thermal paste it was an adhesive (glue) type of thermal paste. Vendor sites like Arctic Silver should provide ideas on cleanup and reinstallation.
You could also take it to a local computer shop or CompUSA and have them do the work.
Did you run the machine to discover the problem or just hear it flopping around inside and investigate before powering up?
I had two brand new Abit motherboards with somewhat the same problem. One out of the box and the second 9 days after installation. The heatsink holddown was soldered wrong and gave way to the pressure of the spring arm. Since they were brand new they went back. Frustrating for you I'm sure.
I hope your problem is resolved by the above procedure.