UNSOLVED

guru3

updated

23 years ago

G

guru3

11 Posts

0

12615

October 21st, 2003 18:00

B800r- Died 3rd reboot after BIOS flash to A08

I just flahsed my Dimension XPS B800r with BIOS A08. It worked, I shut down, I configured the BIOS, I rebooted into Windows ME, I shut down, went to put in a book diskette. After I put in the boot diskette, I went to push the power button, and it won't turnon. It starts making all the right noises and the powerlight goes on for about 1.5 seconds, and then it turns off. Anyone have any idea about what's broken here? Or at least what's not broken? Thanks in advance.
  • NVRambo

    1864 Posts

    474

    0

    Posted October 21st, 2003 19:00

    Pull the power cord from the back of the tower while discharging the power by pushing the front power switch for 5-10 seconds.

    Plug it back and try again.....

  • guru3

    11 Posts

    474

    0

    Posted October 22nd, 2003 16:00

    Ok, as it is out of warranty, I went and took everything appart. I checked the power buttons, they're good. Then, I went to check the powersupply... The 12V output for the deviced is 10V. The 12V output for the motherboard was 22V!! YIKES!! My powersupply apears to have failed. The standby voltage of 5V is OK, so the motherbaord accepts the power on requests. It sees that it's getting a "little" too much voltage and shuts off, in less then 2 seconds. This is not terribly bad news, I'll get a new computer I guess. Is there anything for fixing the powersupply though? There was no loud pop, nothing. Does this seam weird to anyone?
  • shesagordie

    12 Elder

    •

    46017 Posts

    474

    0

    Posted October 23rd, 2003 02:00

    guru3.

    The only way to fix a fried PSU, is to replace it.  This PSU is a proprietary unit and you can buy a replacement from Dell Spare Parts Phone 800.372.3355 Ext 69937 or from the following.

     http://www.pcpowercooling.com/products/power_supplies/selector/index.htm

    Bev.

  • guru3

    11 Posts

    474

    0

    Posted October 23rd, 2003 03:00

    Well, I borrowed a working Dell PSU from a friend and tested it. Unfortunately, same result. So now what's actually wrong? Guess I'm going to be getting a new computer...

  • rickmktg

    2 Intern

    •

    11898 Posts

    474

    0

    Posted October 24th, 2003 00:00



    @guru3 wrote:

    Well, I borrowed a working Dell PSU from a friend and tested it. Unfortunately, same result. So now what's actually wrong? Guess I'm going to be getting a new computer...


    When this is the right solution, I want you to say "Oh my gosh, you're amazing"...

    I'll bet you have an IEEE card, right?  Remove it.  Reboot.  Now downgrade the BIOS to A06 (not A07, you can't use that either).  Reboot.  Now shut down, put in the IEEE card, and you'll be all set. 

    Ok, I'm listening... 

  • guru3

    11 Posts

    474

    0

    Posted October 24th, 2003 03:00

    I'm about to go on vacation but when I get back I'll try that...
  • nickil85

    31 Posts

    474

    0

    Posted October 24th, 2003 13:00

    i had this problem ...exactly the same

    after taking out the ethernet card and sound card...swithcing PCI slots and rebooting around 5 times...it worked and has worked since

  • rickmktg

    2 Intern

    •

    11898 Posts

    474

    0

    Posted October 24th, 2003 13:00

    My B600r died when I upgraded to A08.  Dead.  I then searched and found this problem in only 1 post.  I removed the IEEE board and it booted fine.  Tried A07, no go.  Tried A06, viola!

    Now if I could just find a reason to use the IEEE card

  • guru3

    11 Posts

    474

    0

    Posted November 8th, 2003 12:00

    Yup, it was the IEEE1394 card, just removed it and a general upgrade and things are better... Thanx for your help.
  • rickmktg

    2 Intern

    •

    11898 Posts

    84

    0

    Posted November 9th, 2003 01:00

    Glad to have helped.  If you want to run the card, go back to A06.