
Solved!
Go to SolutionAlienware X51 R3 no boot when connected to 4k TV via HDMI
I have an issue with booting my X51 R3 when connected to my new 4k TV via HDMI. The System does not boot up, no matter if TV ist turned on or off. I have to disconnect the HDMI cable (tried DVI to HDMI as well - same issue) - wait until the System booted to Windows 10 , then connect it and after this Point all works as usual.
Given this fact, i can't get into BIOS - except connecting another TV - i found some Post here concerning the same Problem, but not found a common solution.
I have actual Bios 1.2.8 as well as actual Nvidia Drivers (genuine GTX 970).
Very rarely the System managed to boot into Windows - but no TV Signal present, but it was able to connect to my PC via TeamViewer - and could see inside the Device Manager that the Geforce has been turned off due to "the device reported Problems and was disabled" - after rebooting without hdmi cable - worked again normally.
I connected a Dell Vostro 460 to the 4kTV via HDMI - boots fine - no issues.
So i can only guess it's a BIOS related Problem - but no Change since 1.2.4 what i could read here :/
will be grateful for any advice!!
Responses (13)
Solutions (0)
Research EDID problems over HDMI. Could also be HDCP over HDMI problem, but I don't really think so since you are not even getting to playing any HDCP Protected Content.
Not being able to see BIOS over HDMI is a common problem with any video card.
Do you have a proper .INF file installed for that HDTV display?
Dell Rockstar
Microsoft Windows and Apple iOS Developer (Retired)
- Like many of you, I can appreciate a good game-engine.
- I answer questions here, but I'm not a Dell employee.
- Consider giving posts you like a "thumbs-up"
- Posting models-numbers and software versions speeds trouble-shooting.
- Click "Mark as Accepted Answer" on any post that answers your question best.Thank you for your Reply! I still have the generic Plug & Play Monitor .inf installed... TV is LG OLED55B6V - actual FW, no further Drivers availabe from LG. Never had an issue like this before on predecessor TV and PC, always using HDMI Connection.
i came accross some Posts from People blaming UEFI secure boot - what do you think?
1. Thank you for your Reply! I still have the generic Plug & Play Monitor .inf installed... TV is LG OLED55B6V - actual FW, no further Drivers availabe from LG.
2. Never had an issue like this before on predecessor TV and PC, always using HDMI Connection.
3. i came accross some Posts from People blaming UEFI secure boot - what do you think?
0. EDID is a different thing. Google it.
1. Unfortunate. If Windows-10 can't Plug-and-Play the LG OLED55B6V ... and download a INF (sort of like a driver) from Windows Update, then LG is your only hope.
2. That's nice. Yes, I use HDMI with various computers with no problems also, but usually only "Home Theater" related. For desktops I would rather use DVI or DisplayPort.
3. Doubtful, but possible. I don't own your LG-HDTV or a x51-R3 to test it. I can tell you I have a Lenovo X1-Carbon here with UEFI and SecureBoot active. It's HDMI output works fine with my Onkyo-607 AVR/Amp (which has both a HDMI 1080p plasma and projector connected). Also, works connected directly to Epson projector via HDMI.
I'm just offering ideas. Have you tried connecting it to thru your Home Theater AVR/Amp instead of directly connected?
Dell Rockstar
Microsoft Windows and Apple iOS Developer (Retired)
- Like many of you, I can appreciate a good game-engine.
- I answer questions here, but I'm not a Dell employee.
- Consider giving posts you like a "thumbs-up"
- Posting models-numbers and software versions speeds trouble-shooting.
- Click "Mark as Accepted Answer" on any post that answers your question best.Here is a guide I Googled.
Actual menus might be a bit different on your model TV, but basically the same steps.
Dell Rockstar
Microsoft Windows and Apple iOS Developer (Retired)
- Like many of you, I can appreciate a good game-engine.
- I answer questions here, but I'm not a Dell employee.
- Consider giving posts you like a "thumbs-up"
- Posting models-numbers and software versions speeds trouble-shooting.
- Click "Mark as Accepted Answer" on any post that answers your question best.89fordprobee
1 Rookie
•
1233 Posts
2978
0
Posted February 26th, 2017 15:00
well sitting here on a X51 R3 .. on a Samsung UN55HU8550 4k of course and have no issues but I have a high priced hdmi cable , but even sending via wireless connection to the tv I have no issues with the 4k (after booted of course) and I run my Ark Survival on it.. my daughter loves watching the dino's lol
so as said its possible tv is issue as I have heard of it before ..
89fordprobee
1 Rookie
•
1233 Posts
2978
0
Posted February 26th, 2017 16:00
even sending via wireless connection to the tv I have no issues with the 4k (after booted of course)
when using the wireless intel ...
with hdmi I boot no issues never have but it is an older tv like the OP's original tv but windows does see it as a proper Samsung tv with model # ..
on a Samsung UN55HU8550 4k of course and have no issues but I have a high priced hdmi cable ,
People think that all HDMI cables are the same, but it's simply not the case. I like heavy gauge ones, short as possible, and non-Redmere or anything tricky. They should be spec-ed to handle highest version HDMI port on component in system (v1.4, v2.0, etc.) as well as associated higher bandwidths.Dell Rockstar
Microsoft Windows and Apple iOS Developer (Retired)
- Like many of you, I can appreciate a good game-engine.
- I answer questions here, but I'm not a Dell employee.
- Consider giving posts you like a "thumbs-up"
- Posting models-numbers and software versions speeds trouble-shooting.
- Click "Mark as Accepted Answer" on any post that answers your question best.1. The System does not boot up, no matter if TV ist turned on or off.
2. I have to disconnect the HDMI cable (tried DVI to HDMI as well - same issue) - wait until the System booted to Windows 10 , then connect it and after this Point all works as usual.
1. OK
2. While not a true solution, sounds like a simple HDMI Switch might be an acceptable work-around. It might needed to be spec-ed to handle HDMI v2.0.Dell Rockstar
Microsoft Windows and Apple iOS Developer (Retired)
- Like many of you, I can appreciate a good game-engine.
- I answer questions here, but I'm not a Dell employee.
- Consider giving posts you like a "thumbs-up"
- Posting models-numbers and software versions speeds trouble-shooting.
- Click "Mark as Accepted Answer" on any post that answers your question best.I have no issues with the 4k (after booted of course) Can you elaborate? Sounds like it works for OP also "after booted".
Dell Rockstar
Microsoft Windows and Apple iOS Developer (Retired)
- Like many of you, I can appreciate a good game-engine.
- I answer questions here, but I'm not a Dell employee.
- Consider giving posts you like a "thumbs-up"
- Posting models-numbers and software versions speeds trouble-shooting.
- Click "Mark as Accepted Answer" on any post that answers your question best.

gertsch
6 Posts
3374
0
Posted February 28th, 2017 12:00
Seems like i was lucky, and stumbled over a solution on another Forum.
Long Story short, switching the "Output Color Format" inside the Nvidia Control Panel from RGB to YCbCR444 did the trick. After the next complete shutdown i could see my whole boot process again and entered Windows with HDMI connected all the time :) (did 2-3 cold and warm boots to be completely sure)
it was mentioned in the guide Tesla posted, that RGB did not work properly on Samsung TVs earlier, only after a Firmware upgrade... so maybe LG are on their way there too :/
thank you all!