
UNSOLVED
S
sickertrick
6 Posts
0
13858
November 14th, 2010 08:00
Alienware Aurora locks up after using 3dVision
I have had my Aurora for a week now and when I run 3d ready games (Bad company 2) the system will either lockup during the game or when I exit out of game. Also SLI will automatically disable itself. At one point my video drivers were missing (according to Win 7 device manager). I am also seeing my alien FX being disabled. The Intel storage technology icon is also almost always disabled.
I tried to run the Alienware Diagnostics from the support DVD, but that freezes up at the Blue-ray test (85% completion).
I have tried both the latest drivers on Nvidia and on Dell.
-
Alienware Aurora Desktop
-
I ntel Core i7 930 QC (2.8GHz, 8MB Cache)
-
6GB Triple Channel 1333Mhz DDR 3
-
23.0" Alienware AW2310 OptX Fu ll HD Gaming Monitor, 3D capable (requires nVidia 3D Vision kit, qualified graphics card)
-
Nvidia GeForce GTX460 Dual 1GB
-
1TB - SATA -II, 3Gb/s, 7,200RPM , 32MB Cache HDD
-
Single Drive: Blu -ray Disc (BD ) Burner (Writes to DVD/CD/BD)
-
Genuine Windows 7 Ultimate, 64 bit, English
Responses (8)
Solutions (0)
It seems u did not install ur driver properly:
u can try follow these procedues:
1. Download DriverSweeper, unzip/install it
2. uninstall from Control Panel -> add and remove programs and reboot
3. Tap F2 repeatedly during startup and boost into safe mode4. run Driversweeper in safe mode
5. Let it scan ur system for remnant driver file
6. let dirversweeper delete them and reboot
7. boot into windows, install the gfx driver again.
sickertrick
6 Posts
700
0
Posted November 15th, 2010 14:00
I did finally get the driver installed correctly. The question I have now is, in the Alien Thermal controls all Temp sensors read 26 degrees. They never change, even during or after running a lot of apps. None of the fans seem to ramp up at anytime. The PCI fan is set to 2% and nver increases. If I set the fan to the curve then it ramps up till it get below 26 degrees. Now this you would normally not think is a problem, but adding what GPU-z reports about the one video card, I am a little worried.
Is this normal or am I right in thinking something is not right.
I am new to Alienware, wanted one for years and just finally bought one. I am just nervous I made a mistake.
things will only get really hot if u are performing stress test, the processing power of ur CPU is able to handle the usual apps like steak knife cutting butter. .never be too sure, reinstall the video driver using the suggested method and see what happens. if problem is not solved, u need to re-setup the crossfire/SLI and u can also try switching the PCI-e slots to see whether it is a Motherboard issue.
P.S. 26degree is normal.
sickertrick
6 Posts
700
0
Posted November 16th, 2010 16:00
Problem solved!
One of the Nvidia Cards fan was not rotating causing it to overheat..
The Cause of this is a cable (USB Cable 1) Alienware routed, was up against the fan, causing it not to spin. This was purposely routed this way and not caused from shipping.
repathed the cable (USB Cable 1) so it would not rest against card.
Now I can Play!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Alienware really needs to pay attention to detail.
Hello SICKERTRICK!
Glad to see you solved your problem!!
When I got my Aurora a few days ago the first thing I did was check inside to try and make certain that everything was installed as it was supposed to be and nothing had come loose during shipping. The only thing I noticed wrong was the SLI bridge for my Nvidia cards was not connected and that was all I could see.
Now since you posted this I might take a 2nd look to see if mine is like yours,because one of my cards is always about 10c higher than the other one,but I still do not see excessive heat on them when running stressful applications.
When at Idle 1 card is like around 38c and the other is like 48c to 50c. Is this normal for Nvidia 460 in SLI in the Aurora?
sickertrick
6 Posts
700
0
Posted November 16th, 2010 17:00
Hey lordfess
Yeah when I recieved mine, I found the same bridge has come off.
My temps at idle were around what you are seeing, any game woul;d raise temps all the way up to thermal shutdown (105c). then the computer would lock up.
its not to hard to see with a flashlight, just look under the bottom card, they pathed two cables right uder the fan of the card.
the only other way to prevent this was to raise PCI fan to 60%
DELL-Chris M
Community Manager
•
56891 Posts
•
232143 Points
700
0
Posted November 17th, 2010 06:00
sickertrick,
Send me your service tag number via private message so I can report this manufacturing error.
DELL-Chris M (old account)
#IWork4Dell

sickertrick
6 Posts
700
0
Posted November 14th, 2010 20:00
I also Found when running GPU-Z One video card shows temp at 40 degrees C 25% fan speed and 1110 rpms. the other card shows temp at 82 degrees C 62% fan speed and 0 rpms.