
Solved!
Go to SolutionAlienware Area 51 - Card Reader
After 2 1/2 months, my new system arrived missing a card reader. Not a big deal - I will simply install one BUT ... Does anyone have any idea where the USB cable is? I see that there are three on the main board that run up the side to the top, 2 I would assume are being used by the front USB connectors but I cannot see the third anywhere. How do I get this connected?
Responses (27)
Solutions (0)
shesagordie
12 Elder
•
46017 Posts
1901
0
Posted March 5th, 2010 17:00
m3th0d1c4l
265 Posts
1901
0
Posted March 5th, 2010 21:00
The USB header location is on the MIO board in bottom front of the case, in front of the PSU. I bought one seperately for my XPS 730x, which was swapped out for an Area 51. I figured it would go somewhere on the MIO board, since the XPS did the same.
It will be a black square header on the blue NIO board. It might be a bit hard to reach.
Hope this helps.
The USB header location is on the MIO board in bottom front of the case, in front of the PSU. I bought one seperately for my XPS 730x, which was swapped out for an Area 51. I figured it would go somewhere on the MIO board, since the XPS did the same.
It will be a black square header on the blue NIO board. It might be a bit hard to reach.
Hope this helps.
Were you successfull installing a media card reader in you Area51?
I have been looking for a internal media card reader but can not find one for my Area51. I cant find one with a compatible cable for my system. I dont have any free ports on my MB or my PCI slots to add a USB PCI card.
m3th0d1c4l
265 Posts
1901
0
Posted March 5th, 2010 23:00
My media reader is hooked up perfectly and working great.
Yes, you can use the one from an XPS 630/730/730x. It will fit just fine up top. The cable will not hook up to the motherboard, but to the Master I/O board in the bottom of the case, which also controls your lights, fans, vents, etc. You do not need to buy additional USB cards or anything of the matter. There should be 2 additional USB headers on the Master I/O board for 2 USB devices. When you open the case door, open up the Video Card bay, and look down into the front. You wil see a blue board with an orange glowing light. That is the MIO board, and the cable hooks up to it. Like I said, there are 2 free USB headers on there, you just gotta look through the mess of wires.
I had bought the 19-1 media card reader from Dell for my XPS 730x, but since I had to send it in to them with only the original parts, i took my card reader out and installed it on the Area 51. The one I have is the CA-200 reader from Dell. There is also a CAB-200, which has Bluetooth built into it, if you want that one. They use the same media card reader for the Alienware that they used for the XPS computers listed above.
This one should fit the Area 51 without any problems:
You can also just call up Dell and ask them if you can buy one from them for your PC. But in my experience, the ones from the XPS PC's mentioned above will work without a problem. The one I listed above has Bluetooth. You can find one without Bluetooth for a cheaper price. If you buy it from Dell, the actual cable itself is more expensive than the card reader. It cost me around $40 bucks for it from Dell for the Card reader + the cable. You need to buy both, as they dont come as a set. I think it was $15 bucks for the reader and $25 bucks for the cable.
My media reader is hooked up perfectly and working great.
Yes, you can use the one from an XPS 630/730/730x. It will fit just fine up top. The cable will not hook up to the motherboard, but to the Master I/O board in the bottom of the case, which also controls your lights, fans, vents, etc. You do not need to buy additional USB cards or anything of the matter. There should be 2 additional USB headers on the Master I/O board for 2 USB devices. When you open the case door, open up the Video Card bay, and look down into the front. You wil see a blue board with an orange glowing light. That is the MIO board, and the cable hooks up to it. Like I said, there are 2 free USB headers on there, you just gotta look through the mess of wires.
I had bought the 19-1 media card reader from Dell for my XPS 730x, but since I had to send it in to them with only the original parts, i took my card reader out and installed it on the Area 51. The one I have is the CA-200 reader from Dell. There is also a CAB-200, which has Bluetooth built into it, if you want that one. They use the same media card reader for the Alienware that they used for the XPS computers listed above.
This one should fit the Area 51 without any problems:
You can also just call up Dell and ask them if you can buy one from them for your PC. But in my experience, the ones from the XPS PC's mentioned above will work without a problem. The one I listed above has Bluetooth. You can find one without Bluetooth for a cheaper price. If you buy it from Dell, the actual cable itself is more expensive than the card reader. It cost me around $40 bucks for it from Dell for the Card reader + the cable. You need to buy both, as they dont come as a set. I think it was $15 bucks for the reader and $25 bucks for the cable.
My area 51 is a system replacment. I had the XPS-730x. When I got my Area 51 it didn't have the card reader so I took mine out of the XPS before I returned it. The old cable is only about 6in long since the MCR is right next to the MCB. I have the CAB-200 with BT. I called tech support and told them I took out my card reader but needed the cable and they sent it to me free of cost. When I got the cable it was for the non-BT model so it had a pin that didn't match my cab-200. So i stripped the wire and made one from it and the old cable.
When I connected it to the MCB the BT would work but not the card reader. When I connected it to the MB both the BT and MCR worked. So what I did was unhook one of the top USB from the MoBo and connected it to the MCB. I then plugged my MCR into the MoBo and it's been working like a champ every since.
My Area 51 came with BT so since I got it and the MCR BT I leave the one in the top of the case turned off.
My media reader is hooked up perfectly and working great.
Yes, you can use the one from an XPS 630/730/730x. It will fit just fine up top. The cable will not hook up to the motherboard, but to the Master I/O board in the bottom of the case, which also controls your lights, fans, vents, etc. You do not need to buy additional USB cards or anything of the matter. There should be 2 additional USB headers on the Master I/O board for 2 USB devices. When you open the case door, open up the Video Card bay, and look down into the front. You wil see a blue board with an orange glowing light. That is the MIO board, and the cable hooks up to it. Like I said, there are 2 free USB headers on there, you just gotta look through the mess of wires.
I had bought the 19-1 media card reader from Dell for my XPS 730x, but since I had to send it in to them with only the original parts, i took my card reader out and installed it on the Area 51. The one I have is the CA-200 reader from Dell. There is also a CAB-200, which has Bluetooth built into it, if you want that one. They use the same media card reader for the Alienware that they used for the XPS computers listed above.
This one should fit the Area 51 without any problems:
You can also just call up Dell and ask them if you can buy one from them for your PC. But in my experience, the ones from the XPS PC's mentioned above will work without a problem. The one I listed above has Bluetooth. You can find one without Bluetooth for a cheaper price. If you buy it from Dell, the actual cable itself is more expensive than the card reader. It cost me around $40 bucks for it from Dell for the Card reader + the cable. You need to buy both, as they dont come as a set. I think it was $15 bucks for the reader and $25 bucks for the cable.
I wish I would had done that as well. I had a 730x with reader and I did a system swap and left the media reader in my XPS 730x when I sent it back. I really miss it lol. I appreciate your responce and will check into this ASAP.
Like yours, my Area51 already has BT so I will search for a CA200. I think i might of found a good deal on this one http://cgi.ebay.com/Teac-Flash-Card-Media-Reader-Dell-GT399_W0QQitemZ220445132381QQcmdZViewItemQQptZPCC_Drives_Storage_Internal?hash=item33538dc65d
How long of a cable will I need?
m3th0d1c4l
265 Posts
1901
0
Posted March 6th, 2010 06:00
The cable only comes in one size from what I know, and it should be enough. Its a real tight fit though, I mean it just barely makes it from the bottom to the top. When plugging in the cable for the card reader, I recommend that you plug it into the bottom MIO board first, and then the card reader. You also wont be able to route it through that black "spine-like" cable holder in the Area 51 case. I will try and get some pictures up for you later today to show you exactly how I set it up.
That CA 200 should be fine. You will just need to remove the screws from the side, as the Area 51 doesnt use screws for the drive bays. And the Cables for the CA200 and CAB 200 are completely different. As long as they get you the cable with it, you are good to go.
The cable only comes in one size from what I know, and it should be enough. Its a real tight fit though, I mean it just barely makes it from the bottom to the top. When plugging in the cable for the card reader, I recommend that you plug it into the bottom MIO board first, and then the card reader. You also wont be able to route it through that black "spine-like" cable holder in the Area 51 case. I will try and get some pictures up for you later today to show you exactly how I set it up.
That CA 200 should be fine. You will just need to remove the screws from the side, as the Area 51 doesnt use screws for the drive bays. And the Cables for the CA200 and CAB 200 are completely different. As long as they get you the cable with it, you are good to go.
Cool deal man. I will look forward to your pics. thanks again for you help.
m3th0d1c4l, Thanks, great Pics. It REALLY helps! You are a real "team player" to provide the pics for the forum. Now I understand the connection, esp the MIO Board plug in. Nice work with the pics, it is much clearer than text that says "somewhere (implied) on the MIO board". Also I liked your configuration graphic at the bottom of your message, very classy! (How did you create that??)
(My configuration provided for questions/comments)
Alienware Area-51 (not ALX)
CPU-Intel Core i7 975 @ 4.00GHz
6GB Multi-Channel Corsair Dominator DDR3 at 1866MHZ (3x2GB DIMM) running at 1866MHZ 9-9-9-24-C1, (no OC)
Alienware high performance Liquid Cooling
(3) nVidia GeForce GTX 285 1024MB-triple SLI, (no OC), 3D Mark P33815
Power supply-1000 watt
(additional front mounted Visiontek 450W power supply for the third GTX 285)
(2) - Velociraptor 300MGB Raid 0,
Crystal Disk-Read-204.0, Write-235.9 (not sure why the write is faster than the read, comments?)
Dual DVD Drives: 6x Blu-Ray Burner(BD/DVD/CD) + 16x Samsung DVD-R
SoundBlaster X-FI Titanium sound card (Removed for the third GTX 285 card)
Tactx Keyboard
Kensington Trackball-K64325
MS-XBox controller for PC, Logitech Rumplepad
Creative Turtle Beach gaming headset
Logitech Z 5500 5.1 speaker setup
Dell E248WFP monitor
Dell SP2309W monitor
Samsung Syncmaster 2233RZ 120hz 3D ready 22' LCD monitor 1680X1050
Nvidia Stereoscopic 3D kit

m3th0d1c4l
265 Posts
1906
0
Posted March 6th, 2010 07:00
Here you can see the card reader installed inside and outside. Fits perfectly.
Looking here above, you can just see how I routed the cable from the top, going down to the MIO board.
Lastly, you can see where it would plug into on the MIO board. That black square header is a USB. When looking into the case, it is closest to you on the board. You will need to move some wires out of the way (I removed my 5870's at first to try and locate the header). You should be able to reach in there and connect it. I would connect this cable first, then plug the other into the card reader after.
I hope this helps.