I purchased the QCT1250 without the dust filter and now find DELL won't supply it as an add-on.
First question: is there a reason for this, perhaps special modification of chassis to accept the filter?
Second question: can anyone with this filter tell me what is the type of filter (hole size in mesh or whatever may be appropriate) so I can make my own?
A practical substitute can be made from thin, open-cell synthetic filter foam or washable polyester filter mesh, held in a removable frame. Avoid dense vacuum-cleaner or HEPA material because the QCT1250’s front filter is intended to protect the chassis while maintaining airflow.
Recommended material
Use one of these:
3–5 mm reticulated polyurethane filter foam.
Thin washable polyester air-filter sheet.
Automotive/cabin-filter media only if it is cut thin and does not noticeably restrict airflow.
A coarse pre-filter material, approximately ISO coarse/G2–G3 class if available.
Do not use:
Cotton wool, felt, carpet, or ordinary household dusters.
Very dense HEPA media.
Unsecured loose fibres.
Flammable foam or material that sheds particles.
Simple removable insert
Remove the genuine filter, if fitted, and measure:
Overall width and height.
Thickness.
Position of any locating tabs, holes, or corner features.
Cut the replacement media approximately 1–2 mm larger than the clear opening, but not so large that it bulges.
Make a thin retaining frame from:
1–2 mm ABS sheet,
laser-cut acrylic,
3D-printed PETG/ABS,
or a thin plastic document cover.
Sandwich the filter media between the frame and the front grille.
Secure it mechanically with small clips, hook-and-loop dots, or a removable retaining strip.
Keep the filter removable for cleaning; do not glue media directly over the intake if the adhesive can creep into the fan airflow.
The frame should not obstruct the grille or project far enough inward to contact the front fan, drive bay, or cabling.
Check airflow after fitting
After installation:
Check that the filter is not being sucked inward.
Listen for increased fan speed or tonal noise.
Run a CPU/GPU load test for 10–15 minutes.
Compare temperatures with and without the filter, if practical.
Recheck the filter after the first few days for dust loading.
If temperatures rise by more than a few degrees or the fans run noticeably faster, use a coarser/thinner medium. A filter that leaks slightly around its edges is preferable to one that severely restricts intake airflow, although sealing the perimeter is best once the correct airflow resistance has been confirmed.
BIOS reminder
Some Dell systems provide a BIOS dust-filter maintenance reminder. After fitting an aftermarket filter, check BIOS Setup for an option under a name such as Dust Filter Maintenance, Dust Filter Timer, or Dust Filter Reminder. If the QCT1250 BIOS does not expose this option, use a calendar reminder instead.
For the genuine part, search Dell UK using the QCT1250 service tag or 325-BGKZ, rather than relying only on XYF4J; Dell’s parts system can vary the sellable part number by region and system configuration.
This part number has nothing to do with the warranty. It just snaps on the face of the QCT1250. I have the same computer and want to buy this part, but cannot find it.
Dell after sale service is the worst I have seen. Once they sell something, they don't want to know you. Dell support in Greece gave me the part number XYF4J and a price of 49.99 EUR, asking my delivery details in order to issue an invoice. As soon as I gave them, another Dell department emailed me that this is not available in Greece. Telephone support just did not know and did not care.
A few weeks ago I found this on many Dell sites, but each site sells only within their own country.
This dust filter is a Customer Replaceable Unit and its installation and removal is very simple and described on page 42 of the Owners Manual.
If you ever manage to find it, please post a link to the source here for any of us (including me) who would like to buy it.
anne_droid
6 Operator
•
2631 Posts
•
9681 Points
0
0
Posted September 26th, 2026 14:40
Hi
This will probably invalidate your warranty...
Making an equivalent
A practical substitute can be made from thin, open-cell synthetic filter foam or washable polyester filter mesh, held in a removable frame. Avoid dense vacuum-cleaner or HEPA material because the QCT1250’s front filter is intended to protect the chassis while maintaining airflow.
Recommended material
Use one of these:
3–5 mm reticulated polyurethane filter foam.
Thin washable polyester air-filter sheet.
Automotive/cabin-filter media only if it is cut thin and does not noticeably restrict airflow.
A coarse pre-filter material, approximately ISO coarse/G2–G3 class if available.
Do not use:
Cotton wool, felt, carpet, or ordinary household dusters.
Very dense HEPA media.
Unsecured loose fibres.
Flammable foam or material that sheds particles.
Simple removable insert
Remove the genuine filter, if fitted, and measure:
Overall width and height.
Thickness.
Position of any locating tabs, holes, or corner features.
Cut the replacement media approximately 1–2 mm larger than the clear opening, but not so large that it bulges.
Make a thin retaining frame from:
1–2 mm ABS sheet,
laser-cut acrylic,
3D-printed PETG/ABS,
or a thin plastic document cover.
Sandwich the filter media between the frame and the front grille.
Secure it mechanically with small clips, hook-and-loop dots, or a removable retaining strip.
Keep the filter removable for cleaning; do not glue media directly over the intake if the adhesive can creep into the fan airflow.
The frame should not obstruct the grille or project far enough inward to contact the front fan, drive bay, or cabling.
Check airflow after fitting
After installation:
Check that the filter is not being sucked inward.
Listen for increased fan speed or tonal noise.
Run a CPU/GPU load test for 10–15 minutes.
Compare temperatures with and without the filter, if practical.
Recheck the filter after the first few days for dust loading.
If temperatures rise by more than a few degrees or the fans run noticeably faster, use a coarser/thinner medium. A filter that leaks slightly around its edges is preferable to one that severely restricts intake airflow, although sealing the perimeter is best once the correct airflow resistance has been confirmed.
BIOS reminder
Some Dell systems provide a BIOS dust-filter maintenance reminder. After fitting an aftermarket filter, check BIOS Setup for an option under a name such as Dust Filter Maintenance, Dust Filter Timer, or Dust Filter Reminder. If the QCT1250 BIOS does not expose this option, use a calendar reminder instead.
For the genuine part, search Dell UK using the QCT1250 service tag or 325-BGKZ, rather than relying only on XYF4J; Dell’s parts system can vary the sellable part number by region and system configuration.
Kind Regards
anne_droid