Migration process V3.10 to V4 Unable to perform the operation
Hello, i want to migrate Dell OME V3.10.2 to V4.0.0 and when i enter the credentials on source server V3.10 to the target server i receive this error message :
Unable to perform the operation, make sure that the provided information is valid and/or the provided host is reachable
on the target server V4.0.0, i follow the assistant to prepare the target and on the step 3 i have the message :
Source appliance not ready (not in MAINTENANCE state). 'Migrate Out' steps 2 and 3 must be completed on the source appliance.
@Dell -Charles R thank you for your return, i choice to continue with autosigned certificate on both side, i follow the manual with migration out and in steps but i have this error
I am facing the same issue. When I try to validate user from source to target appliance (step 2) it fails with above message.
I am sure about credentials, I changed password a few times and tried different users too. Validation from target to source works fine and it allows me to progress to step 3 on target. Protocol test works fine too between source and target. What else can it be?
It seems like you are encountering difficulties during the migration process from Dell OME V3.10.2 to V4.0.0. Here are some additional steps you can take to troubleshoot and resolve the issue:
Check Appliance Status: Ensure that the source appliance is in the MAINTENANCE state before proceeding with the migration. If it's not in the MAINTENANCE state, you may need to perform the 'Migrate Out' steps 2 and 3 on the source appliance, as mentioned in the error message.
Firewall and Network Settings: Verify that there are no firewall issues or network connectivity problems between the source and target appliances. Make sure that the necessary ports are open for communication between the two appliances.
Review Logs: Examine the console logs on both the source and target appliances for any error messages or issues. You can find logs under Monitor > Troubleshoot > Logs. Look for any entries related to the migration process that might provide more details about the error.
Validate SSL Certificates: Ensure that SSL certificates are valid and correctly configured on both the source and target appliances. Mismatched or expired certificates can cause authentication issues.
Debug Logging: Enable debug logging on both the source and target appliances to gather more detailed information about the migration process. This can help identify the specific point of failure.
Database Integrity: Check the integrity of the databases on both the source and target appliances. Database corruption can lead to migration failures. Dell OME might have utilities or commands to check and repair database integrity.
Consult Dell Support: If the issue persists, consider reaching out to Dell Software Support for assistance. Provide them with detailed information about the error messages, logs, and the steps you've taken so far. They may have specific troubleshooting steps or updates that address migration issues.
Remember to back up your configurations and data before making any significant changes, and proceed with caution to avoid data loss or service interruptions. If you have access to Dell support resources, utilize them for more specialized assistance tailored to your specific environment.
I hope these suggestions help you in resolving the migration issue.
2. What I am trying to do is "migrate out" step 2 that fails on user validation
3. There is no FW in between target-source, both are on the same VLAN
4. Tried logs, can't export from source, must be too many for a browser to process and allow me to download zip file. Tried on target but found nothing useful there (no errors or even attempts that connection was made from a source. Which log file should I be looking at , I might have missed something)
5. Debugging was on, yes. Which log file is the one that should have migration data?
6. DB seems to be ok, it only fails on user validation, doesn't get as far as DB check.
Is there anything on OME 4.0 that should be enabled in settings maybe to allow incoming "requests" from a source one. Please also note that when I run a connection test as advised above from source to target it works fine (REDFISH protocol)
On page 201: When the export task is complete, the source appliance is ready to stream the data to the target appliance. The banner will display that the appliance is in MAINTENANCE state.
If you still have problems with it you can contact Support directly and they can get a look with you.
The forum is not set up for that type of direct engagement.
I think you didn't understand my message. I can't get pass step 2 on source appliance to get to step 3 (export). No issue on target appliance that authenticates ok to the source and passes step 2.
The problem is to pass step 2 on source appliance, it rejects username/password for some reason.
The installed certificate must be signed by the same Certificate Authority on both the source and destination consoles. The uploaded certificate must have both client and server authentication, and key encipherment enabled for Public Key Usage (Key Usage Extensions). Otherwise, it is considered a nonvalid certificate chain and an upload error is thrown (CGEN1008).
You might take a look at this thread also. It looks similar.
No issue with a cert, step 1 is ok, as I said, issue is with step 2 on a source appliance in which username/password are not being recognized by the target appliance.
1. Click Backup / Restore > Migrate and then select Migrate Out. Migrate out option is only available in OpenManage Enterprise 3.10.x.
2. In Sign Certificate you may choose to Proceed with the self-signed certificate that was shipped with the appliance or continue with a Certificate Authority (CA) signed Upload certificate option. If the CA signed certificate does not include the certificate chain an error will be shown. Proceed with the Upload certificate to upload the certificate that includes the chain
Are you getting any leading or trailing spaces when you copy/paste? Have you tried type it in manually?
I might recommend contact Support directly and ask for Systems Management department and an engineer can get a look with you.
DELL-Young E
Moderator
•
5421 Posts
•
37 Points
1
0
Posted April 14th, 2025 06:06
Self-signed cert should typically work if both the Source OME 3.10.x and target OME 4.x appliance are using self-signed certs.
Both the appliances will also need to be able to communicate and authenticate with each other.
as an alternative, if the issue is found to be related to certificate/certificate chain issues, you can follow the steps in the link below:-
Method to Bypass the Certificate Chain Requirement for OpenManage Enterprise Migration | Dell Singapore
I would suggest you open a case with us to troubleshoot further, maybe have a remote session.
You can use a valid service tag for any of the managed servers in OME to raise a case to the in-country support teams-
Responding via the forum would not be feasible based on the current situation.
Respectfully,
Social Media and Communities Professional
Dell Technologies | Enterprise Support Services
#IWork4Dell
Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!