dczurbano

updated

1 year ago

D

dczurbano

2 Intern

•

11 Posts

0

525

August 4th, 2025 14:16

DS-6505B assign ports to an already configured Zone

Hola, tengo dos switches DS-6505B configurados iguales.
Hay dos Zonas definidas ( DB y STORNEXT ) cada una con susu puertos miembres.
También hay 4 puertos sin asignar que deben ser incluídos en la zona STORNEXT.
Gracias

Hello, I have two DS-6505B switches configured the same way. There are two Zones defined (DB and STORNEXT), each with its own member ports. There are also four unassigned ports that need to be included in the STORNEXT zone. Thank you.

  • dczurbano

    2 Intern

    •

    11 Posts

    0

    0

    Posted August 11th, 2025 14:48

    I was finally able to resolve the problem.
    A CISCO-certified colleague helped me.
    Best regards,
  • DELL-Sam L

    Community Manager

    •

    8150 Posts

    •

    34715 Points

    0

    0

    Posted August 4th, 2025 21:41

    Hello dczurbano,

    What is your current os version of your switch?

  • dczurbano

    2 Intern

    •

    11 Posts

    0

    0

    Posted August 4th, 2025 22:27

    @DELL-Sam L​ 

    DS_6505B-1:admin> version
    Kernel:     2.6.14.2
    Fabric OS:  v8.0.2d
    Made on:    Tue Dec 19 20:05:04 2017
    Flash:      Wed Oct 3 06:47:52 2018
    BootProm:   1.0.11

  • DELL-Sam L

    Community Manager

    •

    8150 Posts

    •

    34715 Points

    0

    0

    Posted August 5th, 2025 17:20

    Hello dczurbano,

    You will need to first add the ports to the zone then you will need to activate the zone configuration. Here is a link to a kb that explains How to configure zoning on Brocade SAN switches. This link is no longer available

    (edited)

  • dczurbano

    2 Intern

    •

    11 Posts

    0

    0

    Posted August 5th, 2025 20:56

    @DELL-Sam L​ Hello.
    The page shows an error.
    We've reviewed several documents, but they're not helpful.
    We don't know why we can access the console, but not via HTTP or HTTPS (which was how the devices were configured a few years ago).
    Unfortunately, the person in charge of Networking no longer works for us, and we don't have anyone to replace them.
    What we need is the step-by-step commands to add ports 12, 13, 14, and 15 to the STORNEXT zone.
    Best regards.

  • Alex410

    1 Rookie

    •

    5 Posts

    •

    2 Points

    0

    0

    Posted August 6th, 2025 12:47

    Is it worth it or not ?

  • dczurbano

    2 Intern

    •

    11 Posts

    0

    0

    Posted August 6th, 2025 12:55

    @Alex410​

    I don't understand the question?
  • DELL-Sam L

    Community Manager

    •

    8150 Posts

    •

    34715 Points

    0

    0

    Posted August 6th, 2025 13:47

    How to configure zoning on Brocade SAN switches Audience Level: Customer

     

     
    This article does not apply to Connectrix DS-6505B
     
     
     

    Instructions

    Below shows the sequence to perform CLI zoning on Brocade SAN switches
    1.) Create the alias and associate a wwn to it.
    alicreate "alias", "wwn"

    2.) Create a zone and add 2 aliases as members to it.
    zonecreate "zonename", "alias;alias"

    3.) Add a created zone to the Zoneset configuration.
    cfgadd "cfg_name", "zonename"

    4.) Save the Zoneset configuration.
    cfgsave

    5.) Enable the Zoneset configuration and make it active on the SAN fabric.
    cfgenable cfg_name






    Additional Information

    Alternatively the same can be achieved using Brocade SAN Administrator GUI

    1.) Plug in the FC Connector into an open port on the switch.
    2.) Login to the server and verify the HBA connection. It should see the switch but not the storage device.
    3.) Login to the Brocade Switch GUI interface. You   ll need Java enabled on your browser.
    4.) Check the Brocade Switch Port.

    On the visual depiction of the switch, click on the port where you plugged in the FC connector.
    The Port Administration Services screen should pop up. You   ll need to enable the pop-up.

    5.) Verify that the Port Status is Online. Note the port number.
    6.) Close the Port Administration Services screen.
    7.) Find the WWN of your new device
    8.) Navigate back to the original GUI page.
    9.) Select Zone Admin, an icon on the bottom left of the screen. It looks like two squares and a rectangle.
    10.) Expand the Ports & Attaching Devices under the Member Selection List.
    11.) Expand the appropriate port number. Note the attached WWN.
    12.) Create a new alias for this device
    13.) Click New Alias button
    Follow menu instructions
    14.) Add the appropriate WWN to the alias
    15.) Select your new device name from the Name drop down menu
    16.) Expand the WWNs under Member Selection List
    17.) Highlight the appropriate WWN
    18.) Select Add Member
    19.) Add the alias to the appropriate zone
    20.) Select the Zone tab
    21.) Select the appropriate zone from the Name drop down menu
    22.) Select the appropriate alias from the Member Selection List
    23.) Click Add Member
    24.) Ensure that the zone is in Zone Config in the Zone Config tab
    25.) Save your changes by selecting ZoningActions -> Enable Config


    Prior to making any changes to your SAN you should always backup the current configuration. The steps to perform a backup of the config are as follows:

    To backup a switch, execute the following commands:

    Telnet/SSH to the switch

    Execute the command configupload

    _ _Follow the prompts with the following guidelines:

    • Name standard:  switchname-month-day-year.txt   IE: cx3-20-fc-sw1-11062010.txt
    • FTP Server: ftp.emc.com/
    • FTP account/password: username/password ] (Fabric OS (dev-DS5000B_SW1)

    If you need to do a restore, you will want to do the same thing, but this time, use configdownload and specify the file you want to use as the restore.

  • dczurbano

    2 Intern

    •

    11 Posts

    0

    0

    Posted August 6th, 2025 14:03

    @DELL-Sam L​

    Dear,
    I repeat, the Zone is already created.
    We just need to add ports to those already assigned to this Zone.

    DS_6505B-2:admin> cfgshow
    Defined configuration:
     cfg:   SW_FC02 DB; STORNEXT
     zone:  DB      DB1; DB2; DB_ARRAY
     zone:  STORNEXT
                    AST3; AST4; SNFS1; SNFS2; STR1; STR2; WKR1; WKR2; WKR3; WKR4;
                    WKR5; XCELLIS1; XCELLIS2
     alias: AST3    1,2
     alias: AST4    1,3
     alias: DB1     1,10
     alias: DB2     1,11
     alias: DB_ARRAY
                    1,9
     alias: SNFS1   1,16; 1,17; 1,18; 1,19
     alias: SNFS2   1,22; 1,23
     alias: STR1    1,0
     alias: STR2    1,1
     alias: WKR1    1,4
     alias: WKR2    1,5
     alias: WKR3    1,6
     alias: WKR4    1,7
     alias: WKR5    1,8
     alias: XCELLIS1
                    1,20
     alias: XCELLIS2
                    1,21

    Effective configuration:
     cfg:   SW_FC02
     zone:  DB      21:00:f4:e9:d4:54:c0:0f
                    21:00:f4:e9:d4:54:bf:7f
                    24:70:00:c0:ff:f0:4b:88
     zone:  STORNEXT
                    1,2
                    1,3
                    1,16
                    1,17
                    1,18
                    1,19
                    1,22
                    1,23
                    1,0
                    1,1
                    1,4
                    1,5
                    1,6
                    1,7
                    1,8
                    1,20
                    1,21

    DS_6505B-2:admin> zoneshow DB
     zone:  DB      DB1; DB2; DB_ARRAY

    DS_6505B-2:admin> zoneshow STORNEXT
     zone:  STORNEXT
                    AST3; AST4; SNFS1; SNFS2; STR1; STR2; WKR1; WKR2; WKR3; WKR4;
                    WKR5; XCELLIS1; XCELLIS2

     
  • DELL-Sam L

    Community Manager

    •

    8150 Posts

    •

    34715 Points

    0

    0

    Posted August 6th, 2025 16:55

    Hello dczurbano,

    To configure or reconfigure a switch is a paid service that is provided. Now I understand that you no longer have your network admin and you are trying to add the ports on the switch to the correct zone and restart the config. First thing, is that you work on one switch at a time. Second is that you will need to do is to create alias for the WWNN of the device that are connected to those ports that need to be added to the zone. Once you have alias created for each device that is connect to the ports, then you will need to add the aliases to the correct zone. Once you have the aliases added to the zone you will want to save the zone configuration before you reboot, reactivate, restart configuration on your switch. Once you reboot your configuration then you can check to ensure that data is flowing over the new ports. When you have confirmed that all is well then you can do the same on your second switch.