Just a note.. all I have is the CLI (no Fabric Manager) on the Cisco MDS.
I'm adding a RHEL 5.8 box to the SAN. HBA cards are configured in the server, wired up to the Cisco SAN Switch. Now I'm stuck on this whole "zoning" thing so the server can see the DMX4. On the switch:
0xb20000 N 50:06:0b:00:00:c9:a2:f2 (HP) scsi-fcp:init fc-gs
[Bog_fcd1]
0xb20100 N 50:06:0b:00:00:11:11:20 (HP) scsi-fcp fc-gs
[Tan_td2]
0xb20200 N 10:00:00:00:c9:8b:73:e2 (Emulex) scsi-fcp:init
[CSF-Mail-Zimbra_sda]
0xb20201 N 10:00:00:00:c9:4c:1f:1a (Emulex) scsi-fcp:init
[Rinse_fc0]
0xb20202 N 50:06:04:8a:d5:31:ee:17 (EMC) scsi-fcp:both 253
[Symm5528_FA8d0]
0xb20203 N 50:06:04:8a:d5:31:ee:08 (EMC) scsi-fcp:both 253
[Symm5528_FA9c0]
0xb20205 N 10:00:00:00:c9:60:0b:ed (Emulex)
[Buttercup_fcs0]
0xb20206 N 50:06:04:8a:d5:31:ee:28 (EMC) scsi-fcp:both 253
[Symm5528_FA9c1]
0xb20207 N 10:00:00:00:c9:6b:7c:33 (Emulex) scsi-fcp:init
[Straw_vmhba0]
0xb20208 N 10:00:00:00:c9:69:fb:50 (Emulex) scsi-fcp:init
[VMdmz_vmhba1]
0xb20209 N 10:00:00:00:c9:6d:58:a1 (Emulex) scsi-fcp:init
[Ginger_vmhba1]
0xb2020d N 50:06:04:8a:d5:31:ee:38 (EMC) scsi-fcp:both 253
[Symm5528_FA9d1]
0xb2020f N 10:00:00:00:c9:96:4f:10 (Emulex) scsi-fcp:init
[CSF_ESX_1_vmhba3]
0xb20210 N 10:00:00:00:c9:9e:43:3c (Emulex) ipfc scsi-fcp:init
[sp-sql-prod_Slot3]
0xb20211 N 50:01:43:80:03:ad:ba:32 (HP) scsi-fcp:init
[gisimage_Slot2]
0xb20212 N 10:00:00:00:c9:9f:4b:be (Emulex) ipfc scsi-fcp:init
[gisprod_Slot2]
0xb20400 N 21:01:00:1b:32:b3:7d:e2 scsi-fcp:target
[csf_vtl_5b]
0xb20500 N 50:06:0b:00:00:c9:a3:00 (HP) scsi-fcp:init fc-gs
[Trident_fcd2]
0xb20600 N 50:06:0b:00:00:5d:ee:74 (HP) scsi-fcp:init fc-gs
[Poseidon_fcd1]
0xb20700 N 50:06:0b:00:00:c9:a2:f8 (HP) scsi-fcp:init fc-gs
[Tartan_fcd1]
0xb20800 N 21:00:00:e0:8b:9a:75:e8 (Qlogic) ipfc scsi-fcp:init
[Newbayou_qlc2]
0xb20900 N 21:00:00:e0:8b:9a:56:e7 (Qlogic) ipfc scsi-fcp:init
[Newsewage_qlc2]
Total number of entries = 22
csf-sw1#
Basically, how do I get this server logged into the SAN? I also need to name the pwwn like he did the others. I would assume I would join the new pwwn to the 201 VSAN since thats where mostly everything is. But I'm completely lost anyway, so I probably don't even know what I'm talking about.
dynamox
11 Legend
•
20419 Posts
•
87439 Points
1741
0
Posted July 3rd, 2012 21:00
cool, so let's go through the steps:
1) Create fcalias for each HBA
config t
fcalias name newserver vsan 201
member pwwn 10:00:00:00:c9:96:XX:XX
exit
end
2) Create zone
config t
zone name zone_newserver_dmx4 vsan 201
member fcalias newserver
member fcalias dmx4alias
exit
3) Add zone to active zone set
to view current zoneset name run this command: sh zoneset vsan 201 | grep "zoneset name"
config t
zoneset name vsan 201
member zone_newserver_dmx4
end
4) Active zoneset
config t
zoneset activate name vsan 201
sh zoneset active vsan 201