UNSOLVED

JoeR10

updated

6 years ago

J

JoeR10

1 Rookie

•

1 Message

1

2770

January 26th, 2021 14:00

Aurora R10, non-Dell ram compatibility question

I’m curious to know if anyone has used Corsair vengeance lpx 32gb (2x16) 3600 cl18 intel xmp ram in their R10.

From the limited research I’ve done I know that it can only run at a max of 3400 if I do the update but my question is if the ram itself will be a good match and will it run well. I’m not looking to max it out or anything, tbh I didn’t really know what I was ordering when I ordered it and now I just want to know if the ram will cause problems and should I return it for the crucial ballistix ram (their website says 100% ryzen compatible and corsairs does not)

Thank you guys in advance and I appreciate all suggestions.

  • Doghouse Reilly

    2 Intern

    •

    396 Posts

    2007

    0

    Posted January 26th, 2021 14:00


    @JoeR10 wrote:

     the crucial ballistix ram (their website says 100% ryzen compatible and corsairs does not)

     


    Depends on how lucky you feel?  You may get the Corsair to function fine and then again you may not.

    I doubt you will have any problems with the Crucial...I didn't...highly recommended...best of luck!

    No problemsNo problems

  • markburv

    2 Intern

    •

    569 Posts

    1963

    1

    Posted January 28th, 2021 09:00

    @AlienPuppy 

    Does the R10 bios have an XMP setting? if so, enable it

     

  • AlienPuppy

    1 Rookie

    •

    9 Posts

    1968

    0

    Posted January 28th, 2021 09:00

    I got the 3200 64GB(2*32) kit. Tried couple of ways to run at 3200 but failed. 

    The ram itself is solid and good. however you probably can only run it at default 2133 and cannot oc it.

    The OC of Alienware R10 is a nightmare now...

  • markburv

    2 Intern

    •

    569 Posts

    1948

    1

    Posted January 28th, 2021 11:00

    Here, if this is your machine, it says up to 3400Mhz.

    @JoeR10 So speculation if any 3600 Ram will run at 3600Mhz.

  • markburv

    2 Intern

    •

    569 Posts

    1950

    1

    Posted January 28th, 2021 11:00

    I have Corsair Vengeance RGB 3200Mhz in my R8, no reason it would not work in R10.

    As to 3600Mhz, that's another subject, it may or may not work, costs nothing to try if it is on it's way @JoeR10 

    Start her up and check fansStart her up and check fansExample Frequency for my 3200 RamExample Frequency for my 3200 Ram

  • AlienPuppy

    1 Rookie

    •

    9 Posts

    1928

    1

    Posted January 28th, 2021 23:00

    @markburv , thanks for the advice.

    XMP option is there with two preset OC1 and OC2. None of them work with my 3200 RAM, and I tried couple of manual clock setting not work as well. After several failures.. I gave up...

    And somehow, I think after upgrading BIOS > 1.0.7, they removed the advanced tab for RAM from AWCC.

    Capture.PNG

     

  • markburv

    2 Intern

    •

    569 Posts

    1925

    1

    Posted January 28th, 2021 23:00

    Waiting for the pic

    In the meantime @AlienPuppy do you have the Corsairs with other ram modules, if so the lowest frequency rules over the higher frequency ram.

  • AlienPuppy

    1 Rookie

    •

    9 Posts

    1897

    1

    Posted January 30th, 2021 21:00

    No, that's the only RAM(32*2) kit I put in the slots.

  • markburv

    2 Intern

    •

    569 Posts

    1885

    1

    Posted January 31st, 2021 01:00

    @AlienPuppy 

    Would be nice to see CPU-Z data, Memory and SPD tabs.

    markburv_2-1609419567096.pngmarkburv_3-1609419583622.png

    My Corsairs are not the LPX ones, I have Vengeance Pro RGB on an R8 (current version here), different Auroras play differently with Memory as different motherboards/CPUs.

    I did note that on those LPX 2x16 3200 tech sheets they are only Intel compatible, same for the 3600Mhz 

    You may want to consider exchanging them, if that is still possible for you, most advise Crucial, check their site as they guarantee compatibility.

  • AlienPuppy

    1 Rookie

    •

    9 Posts

    611

    1

    Posted February 13th, 2021 13:00

    @markburv , Thanks for all the details. Actually, I have already switched to hyperX but still can only run at 2933MHZ.

     

    Screenshot 2021-02-13 131420.pngScreenshot 2021-02-13 131438.png

    Looks like my tRC and uncore Frequency is much lower than yours.