Dell XPS 15 7590 – No HDMI signal on Dell P2723D monitors
Hello,
I have a Dell XPS 15 7590 and I’m using multiple external monitors in different locations.
At work, I use a Samsung U32R590 4K, which works perfectly when connected directly via HDMI from the laptop to the monitor.
At home, I have access to two Dell P2723D monitors (one mine and one my brother’s). With both monitors I experience the same issue when trying to connect them directly via HDMI from the laptop.
If I connect through a Dell WD19S Docking Station, everything works fine. This means:
the HDMI cables are working,
the monitors are working,
the laptop is working,
but there seems to be a specific issue only with direct HDMI connection between Dell XPS 7590 and Dell P2723D.
When I connect the laptop directly via HDMI, Windows does detect the monitor (in Display Settings it shows up as “Display 2” and I can change the resolution), but the monitor itself shows no image. The P2723D displays the following sequence:
Scanning for signal
No HDMI signal from your device
Going into Standby mode
I have already installed the latest drivers and BIOS updates. I’ve been dealing with this issue for a couple of weeks and finally decided to ask for help here.
One high resolution monitor will be OK with that dock, but two will not -- the bandwidth of the dock is insufficient to drive two high resolution monitors.
That dock is USB, not Thunderbolt. If you want two high resolution displays, you will need a WD19T (or a newer T model).
Thank you for your answer, but I think I need to clarify.
At work, I don’t use a docking station, and at home I would prefer not to either, although at the moment I have to. At home I only use one monitor, not two (one is mine and the other is my brother’s—he uses a ThinkPad, and both monitors work fine with his laptop). I’ve tested with different monitors, HDMI cables, and other laptops, so I know the hardware is working properly. What I’d like to know is what I can do to avoid using a docking station at home when connecting to a P2723D monitor.
* Disconnect every cable (including power) and peripheral device from the P2723D * Press and hold in the power button for 8 seconds * Reconnect only the power cable and HDMI cable to the P2723D
* Disconnect/reconnect the provided AC power cable to the XPS 15 7590 left side power port and HDMI cable
@DELL-ChrisM2 Thank you for the suggestion and the detailed description. I tried several times, but nothing has changed. I can only add that when I connect the HDMI cable to the computer or turn on the monitor, Windows makes the usual sound indicating that a device has been connected. In the display settings I can see the device, and I am able to change the refresh rate of the P2723D monitor to 60.011 Hz, 59.998 Hz, 59.951 Hz, or 59.938 Hz and nothing helps.
Hi, I want to add my case here as it might help pinpoint this — I'm having the exact same issue on a Dell XPS 15 7590 with a direct HDMI connection to a Dell S2421HN monitor, and I've done extensive troubleshooting today that rules out most common causes:
Symptoms (identical to OP):
Windows detects the monitor correctly (correct name via EDID), shows it as active in Display Settings, allows resolution/refresh rate changes
Monitor itself shows "No signal" / goes to standby
Connection sound plays on plug/unplug — Windows registers the hot-plug event
What I've already ruled out:
Not the cable — same cable works fine on a different laptop
Not the monitor — confirmed with a Linux Live USB (Ubuntu) — HDMI output works immediately, no extra steps, no driver installation. This strongly suggests the HDMI hardware path (TMDS lines) is fully intact, and this is a Windows/driver/firmware-specific issue, not a hardware fault.
Not GPU drivers — tried both Intel.com and Dell.com Intel UHD 630 drivers (different versions), same result
Not Windows itself — tested in Safe Mode (basic VGA driver) — still no signal, which rules out the "advanced" Intel driver output path as the sole cause
Not color format/HDR — checked Intel Graphics Command Center, RGB/8-bit, nothing "fancy" enabled
Not EDID corruption — checked with CRU (Custom Resolution Utility), no extension blocks, EDID looks clean
Not a fresh-install artifact — this started after a BIOS update roughly a year ago (BIOS was ~2021/2022-era at the time), and persisted through a full clean Windows 10 reinstall via Dell OS Recovery
Current BIOS: 1.35.0 — cannot downgrade below 1.32.0 due to Dell's anti-rollback protection on security-patched versions
Workaround confirmed (matches OP's docking station finding):
USB-C/Thunderbolt output works perfectly — same monitor, same laptop, just via Thunderbolt/USB-C-to-HDMI instead of the direct HDMI port
This points to a Windows-side (driver or GOP/firmware) issue specific to the direct HDMI port on the XPS 15 7590, independent of monitor model (P2723D for OP, S2421HN for me) — since it reproduces cleanly on Linux without issue. Would appreciate if this could be escalated as a firmware/driver bug rather than treated as a monitor/cable/EDID problem, since we've now got at least two independent reports with overlapping symptoms.
ejn63
12 Elder
•
31856 Posts
•
156298 Points
0
0
Posted September 17th, 2025 12:49
One high resolution monitor will be OK with that dock, but two will not -- the bandwidth of the dock is insufficient to drive two high resolution monitors.
That dock is USB, not Thunderbolt. If you want two high resolution displays, you will need a WD19T (or a newer T model).