We have a Dell OEMR XL R7615 server configured with RAID 10 using 21 hard disks.
Could you please advise how I can:
Determine the fault tolerance of the current RAID 10 configuration (e.g., how many disk failures the array can tolerate)?
Identify which physical hard disk is mirrored with which other disk?
Check the RAID configuration and disk-to-disk mirroring/drive relationships using Dell management tools such as iDRAC or support assist file can identify it ?
For 3. Check the RAID configuration and disk-to-disk mirroring/drive relationships using Dell management tools such as iDRAC or support assist file can identify it ?
Standard RAID 10 (striping across mirrored sets) requires an even number of physical disks (minimum 4). In a configuration involving 21 drives on a Dell PowerEdge/OEMR R7615, the array is typically configured as:
20 Disks in RAID 10 (10 mirrored spans striped together) + 1 Hot Spare (Dedicated or Global).
1. Determine the fault tolerance of the current RAID 10 configuration (e.g., how many disk failures the array can tolerate)?
Fault Tolerance Breakdown:
Guaranteed Fault Tolerance: 1 drive failure (array remains 100% operational). If a hot spare is configured, it will immediately rebuild the failed drive’s data.
Array Failure Condition: The array will fail if two drives within the exact same mirror span fail before the hot spare finishes rebuilding.
2. Identify which physical hard disk is mirrored with which other disk?
On Dell PERC (PowerEdge RAID Controller) cards, RAID 10 is structured into Spans. Each span represents a primary mirror pair (or triplet, though PERC typically uses 2-drive spans):
Span 0: Primary Disk A + Mirror Disk B
Span 1: Primary Disk C + Mirror Disk D
(and so on...)
The exact pairing depends on how the controller configured the array
3. Check the RAID configuration and disk-to-disk mirroring/drive relationships using Dell management tools such as iDRAC or support assist file can identify it ?
I'm checking this for you. I will post back when I have a solid answer.
Regards,
DELL-Bridjet V
Social Media and Communities Professional
Dell Technologies | Enterprise Support Services
#IWork4Dell
Was your query answered? Please click Thumbs Up on the post that helped to Mark it as Accepted Answer!
(edited)
Regards,
DELL-Bridjet V
Social Media and Communities Professional
Dell Technologies | Enterprise Support Services
#IWork4Dell
Was your query answered? Please click Thumbs Up on the post that helped to Mark it as Accepted Answer!
DELL-Bridjet V
Moderator
•
118 Posts
•
338 Points
2
1
Posted September 25th, 2026 11:04
Hi @LEE888,
For 3. Check the RAID configuration and disk-to-disk mirroring/drive relationships using Dell management tools such as iDRAC or support assist file can identify it ?
We tried using iDRAC but could not check the disk membership related to the span. I found another way, but I was unable to test it. You may try this method - https://dl.dell.com/FOLDER14850384M/1/PERCCLI_7.3811.0_Windows.zip
Installation method of PERCCLI for Windows:
Alternative Windows Installation:
Using PERCCLI Command Line Interface
Basic Virtual Disk Information
bash# Show all virtual disks on controller 0perccli /c0/vall show
Detailed Span Information
bash# Show detailed information for a specific virtual disk (e.g., VD 0)perccli /c0/v0 show all
The output will include span-related information in the "VD Properties" section:
VD0 Properties: ===============Strip Size = 512 KBNumber of Blocks = 936640512Span Depth = 2 # Number of spansNumber of Drives Per Span = 4 # Drives in each spanWrite Cache(initial setting) = WriteBackDisk Cache Policy = Disk's DefaultEncryption = NoneData Protection = None
Regards,
DELL-Bridjet V
Social Media and Communities Professional
Dell Technologies | Enterprise Support Services
#IWork4Dell
Was your query answered? Please click Thumbs Up on the post that helped to Mark it as Accepted Answer!
Regards,
DELL-Bridjet V
Social Media and Communities Professional
Dell Technologies | Enterprise Support Services
#IWork4Dell
Was your query answered? Please click Thumbs Up on the post that helped to Mark it as Accepted Answer!