UNSOLVED

korman

updated

18 years ago

K

korman

25 Posts

0

741

December 9th, 2008 05:00

New ESX 3.5 u3 Cluster on DMX-1000

I will be deploying a new ESX 3.5 U3 cluster which I would expect to grow to about 8 hosts.

I am gong to be re-purposing 2 FA ports which are assigned to a now retired Mainframe which is direct attached. I was going to VCM enable the ports but am 2nd guessing this because these ports will be dedicated to this ESX cluster and every host will need to see all devices anyway. Does it make more sense not to VCM enable the ports so that every lun is visable by default after being mapped. Any technical reasons this will not work?

Configuration
Virtual Machines - RDM - SRDF/a
112 GB VMFS Configuration Volume (used for VM Configuration files container not replicated)

Thoughts?
  • dynamox

    11 Legend

    •

    20419 Posts

    •

    87439 Points

    475

    0

    Posted December 9th, 2008 05:00

    Mainframe typically connects to Ficon/Escon ports ..are you sure those are regular FA ports ?

    you can enable VCM bit on the FA and unmap VCMDB from that FA. There is no reason for ESX hosts to see VCMDB, you are not planning on doing masking from ESX hosts right ?
  • korman

    25 Posts

    475

    0

    Posted December 9th, 2008 06:00

    These are regular ports not Ficon/Escon. This was a unisys mainframe which looks to a DMX like an open system host.

    I was hoping to not have to mask. This way once a hosts hbas are Zoned to the FAs all luns would be exposed. I use RDM luns for all my production VMS so the lun count can get up there. My current cluster has about 40 luns masked to 4 hosts...

    All hosts in the cluster will need to see all luns for Vmotions
  • dynamox

    11 Legend

    •

    20419 Posts

    •

    87439 Points

    475

    0

    Posted December 9th, 2008 06:00

    These are regular ports not Ficon/Escon. This was a
    unisys mainframe which looks to a DMX like an open
    system host.


    Ohh ..good to know ..i know IBM mainframes require Ficon/Escon.

    I see what you are trying to do, but one concern that i would have is how many ESX farms are you going to have ? Do you want all ESX farms to see all LUNs on the FA ?
  • korman

    25 Posts

    475

    0

    Posted December 9th, 2008 07:00

    Yes this would be a Single Farm/cluster of up to 8 Hosts... I would probably start with 4 hosts but would grow to 8 but would want the ability to vmotion between all of them.

    I currently have 8 FA ports available since retiring the mainframe. The Unissys had 4 direct attached and 4 left un provisioned so that the Mainframe had dedicated access to the processor behind the port.
  • xe2sdc

    6 Operator

    •

    2831 Posts

    475

    0

    Posted December 9th, 2008 07:00

    If all FA ports will offer storage to the same cluster, you can avoid masking .. You'll be always able to introduce it later, if needed ... and it won't be that painful :-)
  • dynamox

    11 Legend

    •

    20419 Posts

    •

    87439 Points

    475

    0

    Posted December 9th, 2008 08:00

    if you think that you will never expand beyond this one ESX farm then you should be ok, do plan long term though ;) , it's much easier to do it now then retrofit a few months down the road. Take a look at this white paper if you have not already.

    Solutions Guide: VMware ESX Server Using EMC Symmetrix Storage