UNSOLVED

Zd183

updated

22 years ago

Z

Zd183

24 Posts

0

3204

January 29th, 2005 03:00

Formatting?

Hey,
 
I plan on getting a new hard drive for my dimension 4300, I was wondering if after I put the drive into the computer, do I have to do anything special when I boot up the computer for the first time with the second hard drive in it. I have seen many things on "formatting" a drive. What is this, and will I have to do it, and if I do, how do I?
 
Thanks!
  • volcano11

    2 Intern

    •

    27973 Posts

    326

    0

    Posted January 29th, 2005 03:00

    If you want to end with the new drive being the C: drive, remove the old drive temporarily until you get the drive formatted and Windows is installed.  Partitioning and formatting of the new drive are part of the Windows XP installation process.  See the following:

    http://www.djdenham.com/Install%20Procedures.htm

    Steve

  • Zd183

    24 Posts

    326

    0

    Posted January 31st, 2005 21:00

    Ok, but if I do not want the new drive to be the C drive, can i just install the new one, and start up the computer and it will be all good?  Will the new drive automatically be named like the E drive or something?
  • volcano11

    2 Intern

    •

    27973 Posts

    326

    0

    Posted January 31st, 2005 23:00

    Perhaps you need to explain better what you intend to accomplish.  Do you want the new drive to be bootable? Do you want it to have the operating system on it?  Or, do you just want the new drive to be a data drive with no operating system?

    Steve

  • volcano11

    2 Intern

    •

    27973 Posts

    326

    0

    Posted February 2nd, 2005 02:00

    You will just have to partition and format the drive and then it can be used as a secondary drive.  See the following (note that although it is a Seagate site, the instructions apply to any secondary hard drive:

    http://www.seagate.com/support/kb/disc/howto/install_xp_disk_mgmt.html

    Steve

  • Zd183

    24 Posts

    326

    0

    Posted February 2nd, 2005 02:00

    I plan on it just being the data drive I guess. What I am going to do with it, is use the new hard drive to install all of my games onto it. The operating system will stay on my current drive.
     

    Thanks!
  • Zd183

    24 Posts

    326

    0

    Posted February 3rd, 2005 00:00

    Ok, thanks for the website. I appreciate it. I just have a few questions.

    First of all, what exactly is a partition?

    Secondly, how do I pick the partition type in the second step of the Partition Wizard, Primary or Extended? as it shows below.

    Partition type:
    Primary – This is the normal selection for drives with less than 4 partitions.
    Extended – This is used if the drive is split in to 4 or more partitions.

    And also, could you explain this paragraph below and what I should set it to.

    Specify partition size in Megabytes - Set the size of the partition (The full drive capacity is the default). If the full partition size is not used, right click on the remaining free space once the wizard has completed to partition that space. Repeat the partition wizard until the drive is how you want it.

    Message Edited by Zd183 on 02-02-2005 09:20 PM

  • volcano11

    2 Intern

    •

    27973 Posts

    326

    0

    Posted February 3rd, 2005 01:00

    Partioning is a way of dividing a single hard drive into more than one hard drive.   If you create 2 partitions, each will be assigned a separate drive letter and behave as separate drives.  Unless you really want to do this, my advice is to make a single primary partition using all available space.  Since this is going to be your data drive, I don't see any advantage to having multiple partitions.

    Steve