UNSOLVED

AndersN2

updated

14 years ago

A

AndersN2

13 Posts

0

3071

December 12th, 2012 16:00

VMAXe 5876 splitter and Recoverpoint 3.5.0.2

I am getting the following error message when doing the SAN diagnostics:

SAN view is empty. Check zoning and LUN masking.

However, when I do a Detect Fibre Channel targets I get the correct response (the VMAXe ports).

So from that I assume te zoning is correct.  I´m using only RPA Ports A & B.

Any help will be appreciate.

Thanks

  • AndersN2

    13 Posts

    1051

    0

    Posted December 13th, 2012 04:00

    Hi Forshr,

    I'm using this version because in the other site I've a AP7600 splitter with 6.4.1a.

    I've made the zones and I could see the RPA wwn logued in the Vmax and the RPA see the vmax wwn as a target. But it Couldn't see any lun, even the GK and the aclx.

    The FA ports are set up correctly.

    I will appreciate any help.

    Andres Nourian

    Emc Argentina

    De: forshr

    Enviado: Thursday, December 13, 2012 07:16 AM

    Para: Nourian, Andres

    Asunto: New message: "VMAXe 5876 splitter and Recoverpoint 3.5.0.2"

    EMC Community Network

    Re: VMAXe 5876 splitter and Recoverpoint 3.5.0.2

    created by forshr in RecoverPoint - View the full discussion

  • forshr

    2 Intern

    •

    1126 Posts

    1051

    0

    Posted December 13th, 2012 04:00

    Hi Andres,

    Firstly I would advise that you upgrade RP the latest version, 3.5 SP1 P1, as there are some enhancement to VMAX splitter code in this release.

    The 'SAN view is empty' message is simply implying that the RPAs cannot see any LUNs. Therefore, can you confirm that you have performed the necessary zoning requirement (all RPAs must be zoned to the same FA ports as the hosts) and the masking view configuration has been set up correctly which should include the creation of the initiator group, port group and storage group. Please note that LUNs must be exposed to the host and the RPAs through the same FA ports.

    You may want to refer to the RecoverPoint Deploying with Symmetrix Arrays Technical Notes document for reference.

    Regards,

    Richard

  • forshr

    2 Intern

    •

    1126 Posts

    1051

    0

    Posted December 13th, 2012 06:00

    Hi Andres,

    Have you created the masking views?

  • AndersN2

    13 Posts

    1051

    0

    Posted December 13th, 2012 09:00

    I'd made the Masking of the GK.

    I didn't tag the devices because the vmaxe is 5876.

    Thanks.

    Andres Nourian

    Emc Argentina

    De: forshr

    Enviado: Thursday, December 13, 2012 09:26 AM

    Para: Nourian, Andres

    Asunto: New message: "VMAXe 5876 splitter and Recoverpoint 3.5.0.2"

    EMC Community Network

    Re: VMAXe 5876 splitter and Recoverpoint 3.5.0.2

    created by forshr in RecoverPoint - View the full discussion

  • forshr

    2 Intern

    •

    1126 Posts

    1051

    0

    Posted December 13th, 2012 09:00

    You need to tag all devices exposed to the RPAs.

    Please refer to the RecoverPoint Deploying with Symmetrix Arrays Technical Notes document which is available for download from PowerLink.

    I own this document and I would advocate that you read through it at your earliest convenienve in order to asist you with this deployment. It could save you a lot time and potential issues.

  • AndersN2

    13 Posts

    1051

    0

    Posted December 13th, 2012 15:00

    You are right!

    I was confused with the Write Protect Bypass (WPBP).

    I´d read the document.  In reference to this sentence is that I made the mistake.

    "After upgrading to Enginuity microcode 5876 or later, the WPBP flag is ignored by the microcode and cannot be enabled. It may be disabled with no consequence. "

    I thought it was in reference of Device Tagging and it was about WPBP.

    Thanks for your support.  I will try Decive tagging tomorrow.

  • 1051

    0

    Posted January 27th, 2014 08:00

    hello richard.

    could you pls attach the document "RecoverPoint Deploying with Symmetrix Arrays Technical Notes"? .. I'm unable to view it on powerlink.

    thanks.

    regards

  • forshr

    2 Intern

    •

    1126 Posts

    1051

    0

    Posted January 27th, 2014 12:00

    Rev A09 attached. Rev A10 is due to be released shortly.


    1 Attachment

  • 1051

    0

    Posted January 27th, 2014 21:00

    thank you, richard.