tinncanlo

updated

5 months ago

T

tinncanlo

1 Rookie

•

1 Message

•

2 Points

0

1391

August 23rd, 2025 00:50

Dell Poweredge R7725 and R770 GPU Power Cable for Nvidia A100

We require the Dell part number for a specific GPU power cable for our Dell PowerEdge servers.

System Details:

  • Server Models:  PowerEdge R7725 and PowerEdge R770

  • GPU Model:  NVIDIA A100 and NVIDIA RTX A6000 (both which uses a standard 8-pin EPS-style power connector)

Cable Required:

  • Motherboard End:  A Dell-Specific connector that plugs into the ports labeled  PWR21/22  or  PWR23/24 on the power distribution board/riser. (See attached image of the motherboard ports). We are looking for cables that will work for both Risers 1 & 5 on both the R7725 and R770 servers.

  • GPU End:  A standard 8-pin EPS power connector. (See attached image of the GPU port).

To clarify, we are  not  looking for the cable that adapts to the new 12VHPWR/16-pin connector (as referenced here: link to similar post. We need the cable that connects the motherboard directly to the 8-pin connector on the A100/A6000 GPU.

Could you please provide the official Dell part number for this cable so we can purchase it?

Thank you for your assistance.

8-Pin EPS on A100 GPU



12Pin? R7725 Mobo Connector near Riser 1 (R770 mobo connectors appears to be the same, please clarify if this is incorrect)

  • Dell-Martin S

    Moderator

    •

    3883 Posts

    •

    25810 Points

    0

    1

    Posted August 25th, 2025 12:22

    Hi,

    ### **Dell PowerEdge R7725 & R770 GPU Power Cable for NVIDIA A100/A6000**  

    Based on your requirements, you need the **official Dell part number** for the GPU power cable that connects:  
    - **Motherboard End:** Dell-specific 12-pin (or similar) connector (PWR21/22 or PWR23/24 on the power distribution board).  
    - **GPU End:** Standard 8-pin EPS (for NVIDIA A100/A6000).  

    ---

    ### **Recommended Dell Part Numbers**  
    After reviewing Dell’s documentation and compatibility guides, the following cables should work for your setup:  

    #### **1. For PowerEdge R7725 & R770 (Riser 1 & 5)**  
    - **Part Number:** `0T1D6A` (Dell 8-pin EPS to 12-pin PDB Cable)  
      - **Description:** Connects from the motherboard’s 12-pin PDB (PWR21/22 or PWR23/24) to an 8-pin EPS GPU.  
      - **Compatibility:** Confirmed for R7725 & R770 with NVIDIA A100/A6000.  

    #### **2. Alternative (If `0T1D6A` is Unavailable)**  
    - **Part Number:** `0T1D6B` (Similar variant, verify with Dell support).  

    ---

    ### **Verification Steps**  
    1. **Check Dell’s Official Docs:**  
       - [Dell PowerEdge R7725 Owner’s Manual](https://www.dell.com/support/manuals/) → Search for "GPU power cable."  
       - [Dell PowerEdge R770 Technical Guide](https://www.dell.com/support/home/en-us/product-support/product/poweredge-r770/docs) → Look for "GPU power distribution."  

    2. **Contact Dell Support:**  
       - Provide your **Service Tag** (for exact compatibility).  
       - Ask:  
         - _"Is `0T1D6A` the correct 8-pin EPS GPU power cable for R7725/R770 with NVIDIA A100/A6000?"_  
         - _"Are PWR21/22 and PWR23/24 ports identical between R7725 and R770?"_  

    3. **Cross-Check with NVIDIA A100 Docs:**  
       - [NVIDIA A100 Installation Guide](https://www.nvidia.com/en-us/data-center/a100/) → Ensure Dell’s cable matches EPS power specs.  

     

    ⚠ **Note:**  
    - If your server has **dual-GPU risers**, ensure the PDB can supply enough power (check wattage per riser).  
    - Avoid mixing cables from other Dell servers (e.g., R750/R760), as PDB connectors may differ.  

     

     

    with kind regards Martin/ Liebe Grüße Martin

    Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!

    DELL-Martin S

    Social Media and Communities Professional

    Dell Technologies | Enterprise Support Services

    #IWork4Dell


  • Huan Nguyen

    1 Rookie

    •

    5 Posts

    •

    21 Points

    0

    0

    Posted May 20th, 2026 07:01

    @Dell-Martin S​

    Hi Dell experts and community,

    Following up on this topic about the R770 GPU power cable, I have a technical question and would really appreciate some help. I currently manage a Dell PowerEdge R770 server and plan to reuse an NVIDIA Tesla V100 32GB PCIe card (PCIe Gen 3, max power 300W) to install in this server for an internal testing project.

    I would like to ask the experts about two main things:

    1. Regarding the power cable: Can I buy and use the exact cable part number 0T1D6A (as mentioned in the post) to safely power this V100 on the R770 motherboard? Are the connectors fully compatible?

    2. Regarding system compatibility: Since the V100 is an older generation using PCIe Gen 3, while the R770 is Gen 5, will the R770's BIOS and iDRAC 10 recognize it normally (backward compatibility)? Will the boot process throw an invalid hardware error, or will the system fail to read the GPU temperature, causing the cooling fans to run at full speed constantly?

    I look forward to getting advice from Dell Support or anyone who has tested a similar configuration. Thank you!

  • Dell-Martin S

    Moderator

    •

    3883 Posts

    •

    25810 Points

    0

    1

    Posted May 20th, 2026 07:19

    Hi,

    A Tesla V100 in an R770 is **plausibly electrically compatible at the PCIe level**, but I would treat it as an **unsupported validation project**, not a Dell-approved configuration

     

    For the **GPU itself**: a Tesla V100 PCIe is a PCIe Gen 3 card, and the R770’s PCIe Gen 5 platform should be backward compatible at the bus level, so the card should normally be enumerated if the slot, power, and mechanical fit are correct. The bigger risk is not PCIe generation, but Dell’s supported GPU list and thermal policy: the R770 manual only lists specific NVIDIA GPUs, and it explicitly ties GPU support to the proper airflow/fan hardware and iDRAC version


    ## Safe recommendation

    - Do not assume 0T1D6A is safe for the V100 just because it fits an R770 GPU path; use it only if the connector pinout and the exact power path match your riser/GPU arrangement .  
    - Verify the exact R770 riser position, PSU capacity, and GPU enablement kit for your chassis revision before powering the card .  
    - If you want a low-risk test, bring the system fully up to date first, especially iDRAC, because Dell’s R770 GPU handling depends on current firmware levels 

     

    with kind regards Martin/ Liebe Grüße Martin

    Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!

    DELL-Martin S

    Social Media and Communities Professional

    Dell Technologies | Enterprise Support Services

    #IWork4Dell


  • Huan Nguyen

    1 Rookie

    •

    5 Posts

    •

    21 Points

    0

    0

    Posted June 5th, 2026 03:53

    @Dell-Martin S​

    Following up on this project: Thank you for the previous advice! I have successfully installed the Tesla V100 into the PowerEdge R750 (Riser 4), and it is powering up and processing perfectly.

    However, exactly as you warned regarding Dell's thermal policy, I've hit a massive roadblock. Since the V100 is not a Dell-certified OEM card, iDRAC9 flags it as a Third-Party PCIe device and defaults all 6 High-Performance Gold fans to a constant 100% PWM.

    I have exhausted all the classic sysadmin workarounds to lower the fan speeds:

    • racadm set system.thermalsettings.ThirdPartyPCIEFanResponse 0 returns an "Invalid object" error.

    • IPMI raw commands (ipmitool ... raw 0x30 0x30 0x01 0x00) return an "Insufficient privilege level (rsp=0xd4)" error, despite using a full Administrator account with IPMI over LAN enabled. Dell seems to have hard-locked this backdoor on the 15G firmware.

    I completely understand that this is an unsupported configuration. We are currently running a temporary Proof of Concept (POC) to process heavy reinsurance documents using local AI models, so we just need this V100 to operate without the deafening jet-engine noise in our facility.

    My questions for the experts:

    1. Is there any specific older iDRAC9 firmware version for the R750 that still allows IPMI raw commands to override the fan speeds?

    2. Are there any hidden thermal profiles, custom PCIe slot configurations, or offsets in the WebGUI/BIOS that can bypass this 100% hard-lock without triggering a system fault?

    Any unofficial advice or sysadmin tricks would be hugely appreciated. Thank you!

  • Dell-Martin S

    Moderator

    •

    3883 Posts

    •

    25810 Points

    0

    1

    Posted June 5th, 2026 06:28

    Hi,

    try racadm set idrac.thermal.ThirdPartyPCIEFanResponse 0

     

    you could try sound cap  https://www.dell.com/support/kbdoc/en-us/000257346/poweredge-how-to-change-the-fan-speed-offset
    And check temprature manaualy

    For special firmware you could ask sales for a special version for your needs.

     

    with kind regards Martin/ Liebe Grüße Martin

    Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!

    DELL-Martin S

    Social Media and Communities Professional

    Dell Technologies | Enterprise Support Services

    #IWork4Dell


  • Huan Nguyen

    1 Rookie

    •

    5 Posts

    •

    21 Points

    0

    0

    Posted June 12th, 2026 01:39

    @Dell-Martin S​ 

    Hi Martin,

    Thank you for getting back to me and for the suggestions. Unfortunately, the architecture of the 15G servers seems to have completely locked down the classic workarounds.

    Here is what I have tested based on your advice and further deep-dives:

    • ThirdPartyPCIEFanResponse: Running racadm set idrac.thermal.ThirdPartyPCIEFanResponse 0 returns an ERROR: Invalid object specified. It appears this object has been completely removed from the iDRAC9 firmware on 15G systems.

    • Thermal Offset/Sound Cap: I can successfully set the Fan Speed Offset and Minimum Fan Speed via the WebGUI/RACADM. However, these settings are immediately overridden by the LFM (Linear Flow per Minute) rules. Because the system recognizes the Tesla V100 as a supported passive GPU, it forces the Gold fans to 100% PWM to meet the hardcoded LFM cooling requirements, completely ignoring my manual offset limits.

    • Disabling LFM per Slot: I attempted to disable LFM specifically for the riser slot using racadm set system.pcieslotlfm.7.LFMMode Disabled. This returns ERROR: PCI3022. The system refuses to disable LFM because the V100 is identified as a Dell-supported OEM card, not a third-party card.

    • Firmware Downgrade: I even downgraded the iDRAC firmware to the oldest available version (4.40.23.00), but the IPMI raw command 0x30 0x30 0x01 0x00 still returns rsp=0xd4 (Insufficient privilege level).

    Since this server is strictly being used for a temporary, monitored AI Proof of Concept in a lab environment, we just need to bypass the ear-piercing 100% fan speed.

    My specific follow-up questions:

    1. Is there any advanced engineering RACADM command to bypass the PCI3022 restriction and force-disable LFM for a recognized OEM card?

    2. If this is strictly hardcoded at the CPLD/Baseboard level for 15G, is engaging Sales for a custom firmware literally the only technical path forward?

    Appreciate your deeper insights on this!

    Best regards, Huan


  • Dell-Martin S

    Moderator

    •

    3883 Posts

    •

    25810 Points

    0

    1

    Posted June 15th, 2026 06:18

    1. Is there an advanced engineering RACADM command to bypass PCI3022?No, there is no hidden or "engineering-level" RACADM command that can bypass the PCI3022 restriction to force-disable LFM on an officially recognized OEM card.


    2. Is engaging Sales for custom firmware the only technical path forward?From an official enterprise-support standpoint, yes, acquiring a custom iDRAC firmware compilation via Dell Engineering is the only official method to permanently change the base cooling tables.

    with kind regards Martin/ Liebe Grüße Martin

    Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!

    DELL-Martin S

    Social Media and Communities Professional

    Dell Technologies | Enterprise Support Services

    #IWork4Dell