UNSOLVED

ToroMata

updated

16 years ago

T

ToroMata

1 Message

0

36456

July 12th, 2007 05:00

Printer 966 Error message: printer communication system stopped working and was closed.

HI,
I just bought a new DELL printer model 966 wireless and is not working properly. This is the error message that pops on my laptop screen: Printer communication system stopped working and was closed. A problem caused working the application to stop working correctly. Windows notify you if a solution is available.
 
I called Dell about 14 times and they can not resolve the problem. The problem is fixed for one day and the same problem comes back the next day. Dell sent me a new printer and the problem still there....
 
Any suggestions?
 
Dell laptop inspiron (os vista)
Dell printer 966
 
Thanks
  • sdaa

    1 Message

    922

    0

    Posted August 8th, 2007 00:00

    I have the same problem (same printer, same OS, same message). For now I have shared the printer through my desktop. That took adding a "discovery layer" to that XP PC. This is progress? I hope we find a resolution. From the number of views this message has had we are not alone.
     
  • ritchied

    12 Posts

    922

    0

    Posted September 29th, 2007 22:00

    I have the exact same problem.  Did you find a resolution?
     
    I find if I reboot, I'm good for about 15 mins. 
  • jsharp22

    5 Posts

    923

    0

    Posted November 1st, 2007 13:00

    I have a Dell Inspiron 1721 laptop with a Dell Wireless 1505 Draft 802.11n WLAN Mini-Card #2.  Also, a Dell Photo All-In-One Printer 966 with a Dell 966 Internal Wireless and Ethernet Adapter installed.  My router is a Netgear NEXT Wireless-N Broadband WNR834B RangeMax.  My OS is Vista, 32-bit.

    I was able to install and run my 966 printer wirelessly at ONLY  54 Mbps speed, with or w/o Security (WEP, WPA, WPA2), but I kept getting the error “Printer Communication System stopped working and was closed” approximately 10 minutes after starting my system.

    I moved my 966 printer next to the router and Ethernet it to the router, since I wanted to run my router and cable modem at a higher speed than 54 Mbps, but still print remotely.  I was able to run at a higher speed and to print, but the same printer problem occurred after 10 minutes of starting my system.

    I checked the Event Log and found that very time the printer error occurred “dlcqmon.exe” was the problem.  I ran MSCONFIG and under the Startup tab, I removed the check mark for both dlcqmon.exe and DLCQCATS and restarted my system.

    I have no idea what those two things do, but my problem went away and my system is running and printing.

    Hope this helps.

  • djzrt

    6 Posts

    923

    0

    Posted July 9th, 2009 09:00

    Posted to soon I guess.  Issue has returned.

  • djzrt

    6 Posts

    923

    0

    Posted July 9th, 2009 09:00

    Amazing that 2 years later dell still doesn't have a resolution for this issue.  I just purchased a new Studio 15 with Vista 64bit.  I connected it wirelessly to my 966.  Even though I could print, I was getting the "Printer Communication has stopped working" message. I have another dell laptop with vista 32 connected that was working fine.  I disabled dlcqmon and dlcqcats in startup and the messages have gone away.  I still can't scan though.

     

    Dell Support's answer was to format and reinstall the OS.

  • PudgyOne

    11 Legend

    •

    30315 Posts

    •

    106638 Points

    923

    0

    Posted July 9th, 2009 10:00

    djzrt,

     

    Things have changed since 2007. Here are the instructions to setup the printer, I even have the Vista 64-bit drivers for you. Follow these instructions and then tell me what happens.

     

    First, let's make sure your computer has the latest Windows Updates, especially .net framework, needed to run many applications and un-install all versions of Java, restart your computer and download and install the latest Java.

     

    I recommend that you use these Recommended Wireless Router Settings for the best communications.

     

    Disconnect your printer. Download and run this patch 

    <ADMIN NOTE: Broken link has been removed from this post by Dell>

    to completely remove the printer from your computer. Run the patch, a MUST on Vista machines, until it prompts you to restart your computer.

     

    Restart your computer.

     

    Download the proper drivers.

     

    XP Drivers

     

    Vista 32-bit Drivers

     

    64-bit Drivers

     

    All other drivers

     

    Install the proper drivers, you'll be prompted when to connect your printer(powered on)

     

     

    As for scanning, if you have the disk that came with the printer, then insert the Printer disk and stop it from running. Go to My Computer and double click on it. Look for the drive with the Dell disk in it. Right click on it, left click explore. Look for the OCR Folder. In the OCR Folder, there is an Abbyy Folder. right click on setup.exe, that's in the Abbyy Folder and left click run as administrator. This will install the OCR program.

     

    You may also need to read this,  

     

     

    How Do I Connect a Dell™ Wireless Printer to a Wireless Network

     

    Choose your printer. Beneath your printer, select your operating system. You'll be redirected to another page. Then click on show all steps. It will walk you through the installation process.

     

     

     

     

    Rick

  • djzrt

    6 Posts

    923

    0

    Posted July 9th, 2009 11:00

    Done all that except for the patch, which is a 32 bit application.  If Dell intends it to work on a 64 bit installation why is it not included in 64 bit downloads?  And why doesn't Dell telephone support have this info?  All they say is reinstall the OS.  Where do I get the OCR if I don't have the disk?

  • djzrt

    6 Posts

    923

    0

    Posted July 9th, 2009 11:00

    Still can't scan, but not sure I have the correct ABBYY.  Printer is a Dell 966.  Computer is a Dell Studio 15, Vista Home Premuim 64 SP1

     

    Also, just got the dreaded "printer communication has stopped" message after doing all you advised.  However printer still prints.

  • PudgyOne

    11 Legend

    •

    30315 Posts

    •

    106638 Points

    923

    0

    Posted July 9th, 2009 13:00

    djzrt,

     

    For scanning, if you want to scan to Microsoft Word, you'll have to search the internet for a 64-bit OCR Program. You can still scan Photos without the program.

     

    Dell just didn't updat their website for Vista 64-bit drivers, yet. An old forum Liason taught me how to locate them for people to install the printers on their Vista 64-bit systems.

     

    How do you have the 966 printer connected? You can try these tweaks...

     

     

    Go to device manager(right click my computer, left click properties, left click hardware, left click device manager)


    Go to the USB Controller section and click the + sign.


    Go to each USB Root Hub and right click on it, left click properties, left click power management. Uncheck the box, allow computer to turn off this device to save power.


    Restart your computer.

    --------------------------------------

    Go to device manager(right click my computer, left click properties, left click hardware, left click device manager). Click on Network and then right click on your wireless adapter, left click properties, power management. Uncheck the box, allow computer to turn off this device to save power.

     

     

    Rick

  • Kateb030

    3 Posts

    217

    0

    Posted January 6th, 2010 06:00

    Hi Rick,

    My 966 Printer is connected via USB, any  ideas how to fix it as I am still getting the error messages.

    Thanks

    Kate